|
|
Track-mounted DH-DC1 (BTRK) 1 drill jumbo
The track-mounted DH-DC1 (BTRK 1) drill jumbo with telescopic drill boom is intended as a universal machine for high-performance drivages in medium section roadways. The crawler base also allows the machine to operate on steep gradients.
|
|
The DRILLMASTER 150 series was designed and manufactured to meet the
toughest mining environments. Featuring a Clark power shift transmission with 3 forward and 3 reverse gears allowing the drill rig to travel the mine with ease.
It is a completely equipped, high capacity drill rig for small sized tunnels and
mine production.
For ease of maintenance and repair the DRILLMASTER 150 series was
designed with the mechanic in mind. The design provides for easy access and removal of all components and hydraulic pumps.
The unit is fitted with RDH'S own unique Drill Control Manifold which features some of the newest hydraulic technology available.
The DRILLMASTER 150 series is a self contained drilling rig with an onboard
compressor and air mist drilling system.
Featuring a solid frame, unlike other single boom jumbos that lack in stability and are unable to operate on uneven surfaces or conditions.
|
|
The DRILLMASTER 100 Series was designed and manufactured to meet the toughest mining environments. Featuring a Clark Power Shift transmission with 3 forward and 3 reverse gears this jumbo travels the mine with ease. Boasting an overall width of only 1321 mm it is capable of drilling in narrow vein headings as well as large headings due to its boom coverage.
For ease of maintenance and repair the DRILLMASTER 100 Series was designed with the mechanic in mind, providing easy access and removal of all components.
|
|
Self-propelled Drilling Truck is a one working station, one extension arm, for drilling shot holes at underground headings of methane-free mines that mine non-ferrous metals ores and/or mineral raw materials.
The working system of the drilling rig is equipped with telescope extension arm of RWP type and telescope drilling frame with a hammer hydraulic drill.
Drilling rig is equipped with a cabin that ensures protection for the operator seating there; the protection against collapse during vertical stroke with the energy of 60 kJ.
Good stability and relevant power transmission system enables the use of the said machine to exploit deposits at headings with the longitudinal grade of (in the traffic direction) to 15° and at headings with across grades to 5°.
|
|
Drift Runner MTI - 1SB
The MTI SB Series single-boom Hydraulic rig is designed for drilling vertical, horizontal, and angled holes in underground production headings.
Drift Runner MTI - 2SB
The MTI SB series two-boom Hydraulic rig is designed for drilling vertical, horizontal, and angled holes in underground production headings.
Vein Runner MTI - 1XSB
The MTI XSB Series single-boom hydraulic rig is designed for drilling vertical, horizontal, and angled holes in underground production headings.
Vein Runner LONGHOLE
Hydraulic center articulated four-wheel drive unit for long-hole drilling in underground mines. It is designed for vertical plane rings, fans and rings.
Montabert HC
1964/1991 : more than 25 years of creativity and innovation. An unequalled experience in hydraulic drilling technique is now applied to the hydraulic drifters.
|
|
Pantofore, manually operated drilling jumbos
Robodrill manufactures on request new Pantofore Jumbos.These Jumbos integrate following :
- Standard available carriers or special design
- BUC universal drilling booms
- MONTABERT drills, feeds and regulation system
- Manual or Semi Automatic drilling controls.
|
|
Robofore, fully computerized drilling jumbos
Robodrill manufactures on request new multiple boom Robofore Jumbos.Our Robofore integrates following :
- CAT 980F Carrier (Alt. : Carrier - Heavy Construction Type Wheel Loader)
- BUPEC robotic drilling booms
- HC107 MONTABERT drills
- MONTABERT feed and drilling regulation system
- MONTABERT computerized drilling system.
|
|
|
|
|
|
Rock Drilling Jumbo Introduction
Among the development and research of the products, Sunward Intelligent independently researches and develops the key technologies of the control system, hydraulic control system and special mechanism of hydraulic rock drilling jumbo, which reaches the advanced level in the world. As the latest product in China, it has been included in the National Construction Machinery “15” Development Direction List. In the past, China relied on imports totally for this product, and this project effectively breaks the situation that the imported products dominate the market in the field, meanwhile it is of great significance to promote national development of large-scale construction machinery and improve technical tunnel excavation of China.
Rock Drilling JumboFeatures
·Telescopiform structure and lifting operator's cab. Ample space for loader to pass for discharging that minimize additional workload.
·High positioning accuracy, high drilling speed(up to 1.5-1.8m/min). less drilling bit wear.
|
|
|
Atlas Copco Boomer is a range of high-capacity drill rigs providing the best overall economy, production capacity and well-proven reliability. The Boomer range can meet all your demands from 6 to 206 m2 coverage area. The unique Atlas Copco boom system offers outstanding flexibility and precision to ensure straight-hole drilling performance in high-quality tunnelling and drifting for mine development and production. An extensive range of rock drills is available from 16 kW up to 30 kW impact power.
|
|
An Auger Boring Machine (ABM) is used to bore horizontally through soil or rock with a cutting head and auger. The majority of ABMs are used to install pipe casing under railroads, highways, airport runways, creeks or any area of ground that cannot be open cut or disturbed in any way.
There are many types of cutting attachments for this machine. They range from Backhoe Teeth cutters for cutting through soil to the Robbins Small Boring Unit for boring hard rock.
Initially the ABM is set up in the starting pit on a predetermined length of track. A backing plate, usually steel or reinforced concrete block, is installed in the wall opposite of the boring to withstand the thrust exerted by the boring machine. The machine bores through the earth with a cutting head and the jacking force is provided by the hydraulic thrust. The pipe casing and auger sections are added as the machine advances. Spoil is removed from the auger through the casing to a door located on the side of the machine.
|
|
Track-mounted DH-DC2 (BTRK 2) drill jumbo
The track-mounted DH-DC2 (BTRK 2) drill jumbo with two telescopic drill booms is intended as a universal machine for high-performance drivages in medium to large-section roadways. The crawler base also allows the machine to operate on steep gradients.
|
|
|
|
|
|
A Double Shield TBM consists of a rotating cutterhead mounted to the cutterhead support, followed by three shields: a telescopic shield (a smaller diameter inner shield which slides within the larger outer shield), a gripper shield and a tail shield.
In normal operation ("double shield mode"), the gripper shoes are energized, pushing against the tunnel walls to react the boring forces. The main propel cylinders are then extended to push the cutterhead support and cutterhead forward. The rotating cutterhead cuts the rock. The telescopic shield extends as the machine advances keeping everything in the machine under cover and protected from the ground surrounding it.
The gripper shield remains stationary during boring. A segment erector is fixed to the gripper shield allowing pre-cast concrete tunnel lining segments to be erected while the machine is boring. The segments are erected within the safety of the tail shield. It is the Double Shield's ability to erect the tunnel lining simultaneously with boring that allows it to achieve such high performance rates. The completely enclosed shielded design provides the safe working environment.
If the ground becomes too weak to support the gripper shoe pressure, the machine thrust must be reacted another way. In this situation, the machine can be operated in "single shield mode". Auxiliary thrust cylinders are located in the gripper shield. In single shield mode they transfer the thrust from the gripper shield to the tunnel lining. Since the thrust is transferred to the tunnel lining, it is not possible to erect the lining simultaneously with boring. In the single shield mode, tunnel boring and tunnel lining erection are sequential operations.
Regardless of the operating mode, working crews remain protected within the shields. Robbins Double Shield TBMs are capable of safely excavating a wide range of geologic conditions on a project. Our Double Shield TBMs are manufactured to suit your project requirements, in diameters from 1.6 m to 15 m (5 to 50 ft).
|
|
Earth Pressure Balance Machines (EPBM)
EPBMs are used for high powered pipe jacking with precise control of earth pressure via operator control of the cutterhead with pressure sensors, jacking speed, screw conveyor operation and foam and bentonite slurry additive system for conditioning of spoils. Akkerman manufactures EPBMs for installation of pipe in the 96"-168" OD range.
|
|
|
|
|
|
If the geology of your tunnel ranges from soft soils to weathered rock, then a Robbins Earth Pressure Balance Machine (EPBM) is the correct technical solution for your project. This is particularly true when your project is located in an urban environment and ground surface subsidence cannot be tolerated.
EPBMs are utilized in the construction of rail tunnels, metropolitan subway systems, highway tunnels, and other projects where the tunnel will be constructed either partly or completely in soft soil beneath the water table.
Robbins has integrated over 50 years of TBM design and jobsite experience into our EPBMs. Nobody has a wider range of experience designing innovative machinery to cope with difficult underground conditions. Our engineers will tailor your EPBM to handle the specific challenges of your project. From "Smooth Flow" cutterheads that reduce friction to super-reliable sealing systems and Variable Frequency Cutterhead Drives, Robbins has taken the traditional EPB design to the next level.
|
|
|
|
|
|
|
A Robbins Main Beam TBM is complex in its design, yet relatively simple in concept. The front of the TBM is a rotating cutterhead that matches the diameter of the tunnel. The cutterhead holds disc cutters (ranging from 11" to 20" in diameter) which are positioned for optimal boring of the given rock type. As the cutterhead turns, hydraulic propel cylinders push the cutters into the rock. The transfer of this high thrust through the rolling disc cutters creates fractures in the rock causing chips to break away from the tunnel face. A unique floating gripper system pushes on the sidewalls and is locked in place while the propel cylinders extend, allowing the main beam to advance the TBM. The machine can be continuously steered while gripper shoes push on the sidewalls to react the machine's forward thrust. Buckets in the rotating cutterhead scoop up and deposit the muck on to a belt conveyor inside the main beam. The muck is then transferred to the rear of the machine for removal from the tunnel. At the end of a stroke the rear legs of the machine are lowered, the grippers and propel cylinders are retracted. The retraction of the propel cylinders repositions the gripper assembly for the next boring cycle. The grippers are extended, the rear legs lifted, and boring begins again.
|
|
|
|
|
|
Robbins Small Boring Units (SBU-As)
The SBU-A is a small diameter rock cutting head (from 24"/600 mm to 72"/1.8 m) that can be used with any Auger Boring Machine (ABM) to excavate hard rock on drives less than 500 ft (150 m). The Robbins SBU-A has been proven on hundreds of jobs across the U.S. Over one hundred contractors in locations around the world have proven the SBU-A works better than any other method of excavating small diameter, hard rock bores.
Robbins Motorized Small Boring Units (SBU-Ms)
If you need to bore a small diameter tunnel in hard rock where line and grade are critical, Robbins offers Motorized Small Boring Units (SBU-Ms). These machines have been specifically designed for long bores (over 500 ft/150 m) with difficult ground conditions. They are offered in cutterhead diameters from 48"/1.2 m to 78"/2.0 m. If you are not familiar with SBU-As, we suggest you read about them before researching SBU-Ms.
Robbins Rockhead (SBU-RHSS or SBU-RHDS)
If line and grade are critical and you have a longer bore (over 1000 ft/300 m in length) for your next project, you should consider the Robbins Rockhead. The diameter range is available between 54" (1.35 m) and 78" (2.0 m). The Robbins Rockhead is a powerful mid-sized tunneling machine available in both Single Shield and Double Shield models.
|
|
|
Microtunneling is the best pipe jacking method for wet and unstable ground conditions or contaminated soils. Microtunneling is generally defined as remotely controlled pipejacking (personnel-entry is not required) whereby the soils at the cutter face are controlled to maintain balance. Some examples of microtunneling applications are crossings under existing utilities, busy highways, railroads, levees, waterways and sensitive wetlands or shaft-to-shaft pipeline installation. An Akkerman microtunneling system is made up of several pieces of machinery that function together, controlled by an operator who monitors and controls the tunneling operations from a console inside a control container on the surface. Akkerman manufactures MTBMs for installation of pipe in the 30" -96" OD range.
|
|
|
Pipejacking Systems are used to hydraulically install underground pipelines within strict alignment and grade tolerances where personnel-entry (i.e. operator located inside the boring machine and/or on the haul cart) is permissible. Akkerman manufactures TBMs for installation of pipe in the 44 "-168" OD range.
|
|
|
|
|
|
Robbins Single Shield TBMs protect workers from broken rock until the tunnel lining can be safely installed. The body of the machine is enclosed in a shield that is marginally smaller than the diameter of the tunnel. The flat, low-profile cutterhead minimizes disturbance of the face as it bores, and prevents large blocks from collapsing and causing excessive boring stresses. The front of the TBM is a rotating cutterhead that matches the diameter of the tunnel. As the cutterhead turns, a ring of hydraulic cylinders provides forward thrust through shoes that push against the tunnel lining. The cutterhead holds disc cutters (ranging from 11" to 20" in diameter) positioned for optimal boring. The transfer of high thrust through the rolling disc cutters creates fractures in the rock, causing chips to break away from the face. Boring and lining installation are performed sequentially. To steer, cylinders orient the articulated cutterhead in the required direction.
Robbins Single Shield TBMs are available in diameters from 1.6 to 15 m (5 to 50 ft). All Single Shields are equipped with high-speed segment erectors for rapid tunnel lining installation. To steer the machine, the cutterhead is articulated. The short shield length enables a small turning radius and minimizes exposure to squeezing ground forces that could potentially trap the machine.
|
|
This type of boring machine is used for tunneling in stable to unstable rock for the excavation of traffic tunnels (road and rail), supply tunnels (water, gas and electricity) and other special applications.
The main elements in the construction of the shield tunnel boring machine are the shield which gives the machine its name, a construction like a steel tube in which all other components of the machine are embedded, the cutter head and its drive housing, the advance mechanism and the robot-like device for installation of the tunnel lining, the so-called erector. The tunnel lining, usually consisting of prefabricated concrete sections, is installed with the erector, protected by the rear shield mantle, the so-called tail shield.
|
|
Earth pressure balance tunnel boring machines
Historically, EPBs were developed in order to do away with the mucking system and the reprocessing of boring slurry. To do this, the soil must ideally consist of fine elements (clay and silt) and natural water. This type of mix is rare, which is why foams were developed.
Basic principle
The earth pressure balance tunnel boring machine or EPB consists of a cutting chamber located behind the cutterhead. This chamber is used to mix the soil + water foam. It is maintained under pressure by the mucking system. The system consists of a screw conveyor whose speed is controlled so that constant pressure inside the chamber is guaranteed. The material exits the screw conveyor via a hatch that can be closed when the TBM is shut down. The material is then removed by a belt conveyor and/or train cars circulating in the tunnel.
|
|
This type of boring machine is suitable for driving in stable rock and is used for the excavation of traffic tunnels (road and rail), supply tunnels (water, gas and electricity), pressure water utility tunnels for hydroelectric plants, tunnels for cable cars high in the mountains, tunnels for geological investigations and other special applications.
The main elements in the construction of the open tunnel boring machine are the cutter head with its associated drive housing, the support construction (the so-called gripper) and the advance mechanism.
|
|
WIRTH has been involved in tunneling and mining for over 100 years, producing the largest, most powerful machines in the world. But within the last 25 years the growing demand for trenchless technology as a means for installing underground utilities, has made WIRTH develop a range of equipment to provide trenchless solutions.
At WIRTH we believe that a combination of a high installed power & superior engineering means the user is on to a winning formula. Unlike large diameter TBMs which are made project specific, microtunneling machines are modular and can be adapted to suit a variation in ground conditions and product pipe sizes. This means that a contractor having a system is able to be versatile in the work that he can compete in by either increasing the diameter of his machine, or renting the head he requires for this project. Or maybe he just needs to change the configuration of the machine for use in a harder ground formation by getting a rock head for his existing machine.
|
|
Tunneling systems for mixed ground
Dual mode - two process technologies in one
As the term 'dual mode' indicates, two process technologies are combined in these machines.
Shield machines
These machines are externally similar to shield machines and combine the functional features of a hard-rock shield tunnel boring machine and, optionally, of a slurry shield or a hydroshield machine (Bentonair, slurry shield). They are always used when tunnels have to be driven alternately in stable and unstable sections.
New style machines
Dual-mode tunnel boring machines are still a new type of machines and have been developed to meet the requirements of complex projects in strongly varying geologies. Where conventional tunneling techniques had to be used formerly, these machines now open the way to lower-risk and lower-cost tunneling in difficult geological conditions
|
|
This type of boring machine is used for tunneling in stable to unstable rock for the excavation of traffic tunnels (road and rail), supply tunnels (water, gas and electricity) and other special applications.
The main elements in the construction of the shield tunnel boring machine are the shield which gives the machine its name, a construction like a steel tube in which all other components of the machine are embedded, the cutter head and its drive housing, the advance mechanism and the robot-like device for installation of the tunnel lining, the so-called erector. The tunnel lining, usually consisting of prefabricated concrete sections, is installed with the erector, protected by the rear shield mantle, the so-called tail shield.
|
|
Slurry shield tunnel boring machines
Bentonite slurry, consisting of a specific clay and water mixture is universally used in boring and digging operations. The slurry has numerous properties: sealing of the cutting face, reduced friction on the TBM's structure, and transport of cuttings to the separation plant outside the tunnel.
The basic principle of this TBM is to maintain the tunnel's cutting face during the excavation phase by filling the working chamber, located behind the cutterhead, with slurry.
Slurry pressure is carefully controlled by a large air bubble which is maintained by a separately-controlled air supply system. This air bubble acts as a damper by absorbing sudden variations in mucking output.
|
|
All-new hydraulic wheel jumbo features high capacity HD210 drifter with a new dual damper mechanism attains the extremely highly drilling performance and prolongs the service life of drilling tools.
Experience how smooth and speedy drilling can be.
|
|
All-new hydraulic wheel jumbo features high capacity HD210 drifter with a new dual damper mechanism attains the extremely highly drilling performance and prolongs the service life of drilling tools.
Experience how smooth and speedy drilling can be.
|
|
|
Our Long Tom rigs have been around for over twenty years, and are still in demand due to their simplicity and cost effectiveness. Designed to alleviate the negative aspects of hand held drilling and to improve drilling productivity.
|
|
Terex® MK65 Jumbo Drills
The MK65HE is an electric drill, diesel tram, rubber tired, two boom Jumbo designed to drill drifting holes, crosscut holes, bench holes and rockbolt holes.
SPECIFICATIONS MK65 JUMBO DRILL
Maximum hole depth: 12' 5" (3.81m)
Boom face coverage height: 21.25' (6.48 m)
Boom face coverage width: 35' (10.67 m)
Maximum tram speed: 6 mph (9.60 kph)
Length (depending on feed): 43' (13.15 m)
Width: 7' (2.13 m)
Overall height - Tramming: 8' (2.44 m) w/canopy
Overall height - Drilling: 11' (3.35 m) w/canopy
Maximum gradeability: 35%
Ground clearance: 1.25' (.38 m)
|
|
|
|
