|
|
Partial Profile
Partial profile threading inserts are available in two types with thread angles of 60° and 55°.
- 60° TYPE (ISO and Unified)
- 55° TYPE (British Standard Whitworth)
The partial profile inserts cut without machining the crest of the thread. The same insert can be used for a range of different thread pitches. |
|
Brake actuators
More safety, performance & reliability
Brake pressure proportional effort
For single & dual circuit
Small, lightweight package
|
|
The brake system onboard a vehicle is vital for the safety of the vehicle. It is therefore important that the design of the vehicle and the design of the brake system are co-ordinated to give the optimal safety and good performance and that complements other modern cab ergonomics to reduce operator fatigue and give good machine feel.
The valves may be used in open centre, closed centre and load sense hydraulic systems.
The high flow capability of the valve permit use with wet brakes, which typically require more flow for actuation.
Reduced mechanical drag and power loss by allowing the wet brake discs to be further apart when not applied.
A wide range of actuating forces can be specified, including stagemodulating springs for more progressive feel.
A floor-mounted pedal is available in a range of pre-set angles, with optional heel plates.
The valve may be mounted vertically or horizontally beneath the pedal. |
|
Quality screws
We offer a vast range of screws in order to sadisfy the customer needs.
Self drilling screw, self tapping screw
ITEM
L001 |
|
The bush with its cutting slot is a self-tapping attaching part which ensures screwed assemblies for high loads, without wear in case of frequency disassembly of the screw and resisting vibrations in materials with low shearing strength:
light alloys
cast iron, brass, bronze,
non-ferrous metals,
plastics,
laminates, hard woods,
chipboard panels.
Material:
Cemented steel
quenched, zinc plated
yellow bichromate treated
S 250
U-Z36Pb3 brass
Stainless steel
18.9
Other dimensions and materials on request.
Tolerances on tapping 6H over the full length ± 0.2 mm. |
|
| ... products without technical information |
| |
| The press is used for splitting adjusting, maintenance and try-out operations on dies and molds (thermoplastics, die casting, thermosetting, rubber and blanking) and it is possible to inject special waxes, at low pressure, into the mold. |
|
Our electronic mold spotting try-out presses are innovative and unique. Appreciated world-wide for their high quality and precision, they continue to provide maximum reliability years after purchase. Consistently the Millutensil presses offer outstanding advantages to all die and mold manufacturers.
ADVANTAGES:
- Quality dies and molds are produced quickly
- Fast checking, adjustment and die and mold injection testing
- Remarkable savings in labour costs
- Easy to use; error proof operation
- Movements can be repeated with absolute precision
- The upper half of the die or mold can be rotaded 100° or 180° (option)
- The lower half of the die or mold can be shifted and turned 70° to either the left or the right.
|
|
| ... products without technical information |
| |
... see all the products in the category
Presses
|
| ... products without technical information |
| |
Re-circulate metered amounts of exhaust gas into the engine's intake system to help limit the formation of nitrogen oxides (NOx) emissions. Delphi offers a family of Diesel Exhaust Gas Recirculation Valves based on a proven electronically actuated diesel exhaust gas recirculation valve technology.
Delphi Diesel Exhaust Gas Recirculation Valves are available with single poppet, dual poppet, and butterfly valve designs to help meet all ranges of flow requirements for diesel engines. They are available with solenoid, torque motor, or direct current motor actuators to help meet individual customer requirements for force, response, cost and leak.
Delphi Diesel Exhaust Gas Recirculation Valves are designed for engine programs targeted to meet future exhaust emissions requirements in Europe, North America, and Asia. They are designed for both highway and off-highway applications. |
|
An advanced variable valve actuation technology that changes valve lift, duration and timing when opening and closing intake and/or exhaust valves during engine operation. The Delphi 2-Step Valve Lift System is designed specifically for overhead cam engines that include hydraulic lash adjusters and roller finger followers.
Delphi's 2-Step Valve Lift System is a simplified design that provides manufacturers with a high benefit-to-cost ratio, especially when compared to other powertrain strategies.
Delphi's in-depth understanding of the combustion process and its vast research and development capabilities have enabled continuing innovation. |
|
| ... products without technical information |
| |
Specification:
Capacity: Mild steel up through 10 gauge (3.5 mm). Application: Punch mild steel, aluminum, fiberglass and plastic. Hole Sizes/Conduit Sizes - Hole size is outside diameter of US conduit sizes. Example: 1/2" conduit size punch actually makes a 7/8" hole. Pg Sizes: European standard pipe sizes. ISO Sizes: International Standards Organization pipe sizes. Operation: Battery, hydraulic, ratchet or manual drivers. When used with ratchet, hydraulic or battery drivers, buy the punch and die only; the draw stud is part of the driver kit.
Description:
- Round Standard Metal Punch Units are complete units consisting of punch, die and draw stud.
- Use with battery-powered, hydraulic, ratchet or manual drivers.
- Properly assembled through pilot holes, they will make clean, fast and accurate holes. |
|
Landis Thread and Form Rolling program includes:
Thread rolling heads, rolls, consumables and spares
Machine rolls
Replacement rolls - all makes
Along with our range of standard items shown on our site, we can produce a number of special products for your application. |
|
Landis Reamer Program
Landis Reamers for reaming, chamfering, and facing come in four basic styles - solid, detachable blade, insert blade and composite. The style supplied will depend upon the operation to be performed and the type of Landis die head in which it will be used. They can be identified by a symbol number stamped or etched on one of the flutes of the solid and composite reamers and on each one of the blades of detachable and insert blade-type reamers. |
|
| Create stronger threads faster with better finishes using Landis CNC Thread Rolling Tools. Compact in size, with a small working envelope, they’re ideal for large and small lot production on automatics and CNC machines. Landis CNC Thread Rolling Tools are designed for thread sizes from #0 to 5/8" and material hardness to 24 Rockwell C. |
|
|
|
see the results for the following category
