|
|
It's ideal for flow troubleshooting, balancing and checking performance of permanent flow meters. The new PDFM 5.0 is fast and easy to operate – you can mount the sensor on the outside a pipe in less than a minute. Use the built-in keypad and calibration menu to set up the flowmeter for your application. The PDFM 5.0 works on any liquid containing bubbles or solids and is recommended for "difficult liquids" like wastewater, slurries, sludge, chemicals, viscous liquids and abrasives. Measures flow through most metal and plastic pipes including PVC, ductile iron, carbon steel and stainless steel.
- Strap-on Ultrasonic Sensor works on 12.5 mm to 4.5 m diameter pipes
- Internal Battery and/or AC Powered
- Fast, Easy Set-up with Built-in 5-Key Calibrator
- Large Backlit LCD Display
- Programmable Totalizer
- 300,000 point Data Logger
- USB Output and Windows Software
- 4-20mA Output
|
|
Recommended for clean fluids like water, glycol, oil and most chemicals. Portaflow PT500 ultrasonic sensors strap-on the outside of vertical or horizontal pipes from 13 to 2000 mm pipe materials. Sensors can be mounted without shutting down flow and there is no obstruction or pressure drop. Flow rate and totalizer are displayed continuously along with battery status, signal strength. Press one key to instantly change the units of flow measurement. Real time flow can be displayed in large numeric values or as a graph.
- Strap-on Ultrasonic Sensors
- Internal Battery and/or AC Powered
- Large Backlit LCD Display
- Easy Calibration and Set-up
- 98,000 point Data Logger
- USB and 4-20mA Outputs
|
|
|
|
|
|
Stingray Portable Open Channel Flow Logger
A new, portable logger for area-velocity flow surveys in sewers, open pipes and channels. Stingray is designed for municipal stormwater, combined effluent, raw sewage, irrigation water and stream flow.
Stingray uses a submerged ultrasonic sensor to measure both Velocity and Level in the channel. It is mounted in the channel with a stainless steel bracket or a pipe band. No calibration is required. It operates up to 4 years powered by standard Alkaline D-cell batteries. Electronics are housed in a watertight IP67 enclosure and rated for operation from –15° to 60°C.
Each Stingray includes Greyline Logger software to retrieve and display logged data by RS232 or modem connection. The software calculates flow for round, rectangular, trapezoid and egg shaped channels plus flumes and weirs. After the data is downloaded, the software automatically creates a flow chart based on the pipe or channel size. The software displays it as a graph or a table, or you can export it to a spreadsheet program.
|
|
Measure flow from outside a pipe. The Greyline DFM 5.0 is designed for "difficult liquids" that would damage regular flow meters - wastewater, slurries, sludge, chemicals, viscous liquids and abrasives. There is no obstruction to flow and no pressure drop. The standard, strap-on ultrasonic sensor fits any pipe 1/2" (12.5 mm) Inside Diameter or larger. The electronics/display enclosure can be mounted nearby.
- Non-Contacting Ultrasonic Sensor
- Large, Backlit LCD Display
- 12-Digit Totalizer
- Reverse Flow Measurement
- Isolated 4-20mA (1000 ohm)
- 2 Programmable Control Relays
- Automatic Sensitivity Adjustment
- New Signal Processing System
- Built-in 5-Key Calibrator
- RFI Rejection Filters
- Optional 2 million point Data Logger with USB output to Flash memory
|
|
|
Dynasonics hybrid ultrasonic flow meters utilize both Doppler and transit time sound techniques and automatically select the correct technology to calculate the flow rate. This dual technology provides an accurate measurement of the volumetric flow of clean, solids-bearing or gaseous liquids on full pipes. Adverse flow conditions - surges, particulate, gas pockets, etc. - will not clog, damage or influence accuracy of the "flow-through" meter design.
|
|
FLUXUS® ADM 8027 is an ultrasonic flowmeter with IP66 enclosure for permanent installation in explosion-hazardous areas. It is ATEX certified for use in explosion hazard zones 1 and 2. All electronic components are in a flameproof enclosure. Terminals and terminal boxes are designed in protection type "increased safety".
|
|
The 2151P Flow System is similar to the 2151 intrinsically safe Area Velocity Flow Meter, but is designed to operate from AC power for long-term or permanent applications rather than from battery power for shorter-term, portable applications. Like all 2100 Series modules, the 2151P is set up via connection to a computer running Flowlink Software.
The intrinsically safe design of the 2151P module and flow sensor allows them to be installed in Class I, Division 1, Groups C and D hazardous locations. The concept of intrinsic safety is to limit the energy available to a given circuit or device to a level where electrical discharge (sparking) cannot ignite the hazardous (flammable or explosive) atmosphere. With no spark ignition possible, the equipment can operate safely in areas with hazardous atmospheres.
|
|
2150EX Flow Meter for Zone 0 locations
Area Velocity meter - Baseefa approved as ATEX Group II, Category 1G
The 2150EX is an intrinsically safe Area Velocity Flow Meter that is specifically designed and Baseefa-approved for use in Zone 0 and Zone 1 potentially explosive atmospheres under ATEX Directive 94/9/EC.
The AV 2150EX smart Area Velocity probe is built on digital electronics, so the analog level is digitized in the sensor itself. The probe is also factory-calibrated for 3 meter span at different temperatures. This superior built-in calibration eliminates temperature drift in the level signal, providing long-term level stability that reduces recalibration frequency and completely eliminates span recalibration.
The 2150EX is powered by two lithium or rechargeable lead acid battery packs, or by the 2194EX network interface module. Highly efficient power management provides battery life up to 8 months with two-minute data storage interval.
|
|
|
Dynasonics TFX Ultra ultrasonic flow and energy meter clamps onto the outside of pipes and do not contact the internal liquid. Available in stand alone flow meter or as an energy flow meter used in conjunction with dual clamp-on RTDs measuring energy usage. Available in integral and remote mount systems, both in a rugged, aluminum enclosure. Reduced material costs, installation time and maintenance costs make this the ideal flow meter for nearly all liquid applications.
|
|
|
|
|
|
Clamp-on ultrasonic flowmeters
The SITRANS F US clamp-on ultrasonic flow technology offers several advantages, number one being the utilization of external transducers. These are quickly and easily mounted on the outside of the pipe, making them the perfect choice for retrofit applications and applications where corrosive, toxic or high pressure liquids and gases rule out the option of cutting the pipe.
With the use of the WideBeam technology, clamp-on flowmeters from Siemens have proven their superiority in both the field and the lab. They offer several benefits such as measurement of practically any liquid and gas; performance unaffected by viscosity, flow rate, pipe size, solids and aeration content; high accuracy and repeatability through automatic temperature compensation and zero drift correction; and installation flexibility on pipe sizes up to DN9140 (360 inches). They are available in six families: two geared towards general industry solutions and four tailored to energy, liquid hydrocarbon, gas and portable installations.
Combine this with flexible configuration options that allow you to either customize your flowmeter or to order complete systems, you can rest assured that we have the right solution for you.
|
|
|
The Series TFXL ultrasonic transit time flow meter is a reliable and cost-effective flow meter designed to replace mechanical meters where liquid conditions damage or impede operation. This non-invasive flow meter requires no maintenance, as it clamps on to the outside of the pipe. It provides a 4-20mA analog and simulated turbine meter frequency output, interfacing with a variety of monitoring equipment. The TFXL is available in an integral mount system for pipes size .5" (12mm) to 2” (50mm), and a remote system for pipes size .5" [12mm] and larger.
|
|
|
|
|
|
The battery-powered ultrasonic flowmeter FLUXUS® F601 is an ideal tool for service work and quick control measurements. Its clamp-on flow transducers are simply mounted onto the pipe from the outside and are thus quickly installed, without process interruption.
The measurement is pressure independent and can take place on pipes of almost any materials and on almost any liquid. Transducers are available for pipe diameters from 6 mm to 6500 mm and for temperatures ranging from -40°C to 400°C (more). Two pairs of transducers usually are enough to realize all standard industrial applications. FLUXUS F601 is thus highly flexible and can be used on the most various applications on totally different measuring points.
FLUXUS® F601 has been engineered for the harsh conditions of industrial installations. Its housing is water and dust tight and resistant against oil, many liquids and dirt. The meter and its many accessories are delivered in a sturdy waterproof transport case which dimensions fulfil the airline requirements for carry-on luggage.
Thanks to advanced battery management and Lithium ions battery, F601 allows for more than 14 hours of battery-powered measurement. The remaining battery capacity is displayed and helps planning measuring campaigns realistically.
Beside the standard version, F601 can also be delivered with a wider range of signal inputs and outputs (Multifunctional version), as well as in the Energy version with high precision temperature probes making the energy measurement more powerful than ever.
|
|
|
|
|
|
Our Innova-Sonic digital liquid flow meters are state-of-the-art universal transit-time instruments incorporating the latest advances in digital signal processing. The Innova-Sonic™ Portable Model 210 clamp-on features an industry-unique Bluetooth® wireless PDA interface for a truly flexible and convenient liquid flow measurement tool. Innova-Sonic™ Model 205 is our dedicated/fixed display readout version with non-invasive clamp-on transducers.
Our Innova-Sonic™ Insertion Model 205 features insertion transducers resulting in high signal strength in challenging applications and extremely large pipes.
While principally designed for clean liquid applications, all instruments in our Innova-Sonic family are tolerant of liquids with small amounts of air bubbles or suspended solids common in most industrial environments. All Innova-Sonic liquid flow meters offer low power consumption, high reliability and outstanding applicability at an economical cost.
UNIQUE PRODUCT FEATURES
- Accuracy better than +/-1%
- Wide operating temperature range -40F to +212F (-40C to 100C) (210 Innov-Sonic)
- One meter for a wide range of pipe sizes 1-200” (25mm-5000mm)
- 256MB Tungsten™ T5 PDA interface with Bluetooth wireless
- Numerical and graphical display interface
- Battery power supply with battery recharge port (including spare battery)
- Low installation effort and costs
- Wide bi-directional Flow range of 0 to 40 fps
-Measurement is independent of fluid conductivity
|
|
|
The Series TFXP Portable Transit Time Flow Meter features an advanced non-invasive flow measurement technology, providing a system with unsurpassed accuracy, versatility and ease of installation. Although designed for cleaner liquids, the flow meter can reliably measure liquids containing moderate amounts of suspended solids or aeration. Designed for long or short-term flow measurement surveys on full pipe liquid systems.
|
|
|
Series UFX Hand-held Doppler Flow Meters provide accurate and reliable flow velocity assessments in closed pipe, liquid systems. UFX requires that the liquid be either solids-bearing or aerated at a minimum of 100 ppm. The product utilizes a single, hand-held transducer which is placed on the outside of metal or plastic pipe. Within seconds after placing the transducer, the large LCD will provide a velocity reading in either FPS (feet per second) or MPS (meters per second). The UFX comes with a flow calculator/slide chart for conversion of velocity measurements to popular volumetric measurements.
|
|
|
|
|
|
Portable ultrasonic flowmeter FLUXUS F601 is ideal for troubleshooting, plant optimisation and for control of permanent meters.
Features
* Wide application range thanks to the ability of the transmitter to work with shear wave AND lamb wave transducers at all frequencies
* A single pair of shear wave transducers fits a wide pipe diameter range
* Rapid installation without process interruption
* Bi-directional measurement
* High measurement dynamics
The FLUXUS ® G ultrasonic flowmeters use the proven "clamp-on" technology. The flow transducers are simply clamped onto the outside of the pipe. The measurement can hence be put into operation without cutting into the pipe and without production stop. The installation costs are low, retrofitting is not a problem.
Since the transducers are not in contact with the gas, there is no possibility of chemical attack. There are no moving mechanical or pressure loaded parts and thus no wear an tear. FLUXUS G is ideal for measurements at high pressures or on lines with pressure peaks.
Two transducer types for a uniquely wide application range
All FLUXUS® G transmitters support both lamb wave and shear wave transducers at all transducer frequencies. In this way the measuring system can be optimized to even the most demanding applications.
The Lamb wave transducers are ideal for measurement at high flow velocities, in natural gas pipelines for example, or at low pressures, amongst others in compressed air circuits. The shear wave transducers cover a wide range of pipe diameters and wall thicknesses. They are the best choice for mobile measurement or for high pressure systems.
|
|
|
|
|
|
The FLUXUS F601 is a portable ultrasonic flowmeter. With its clamp-on transducers and its rechargeable battery, it is an ideal tool for service work.
The clamp-on flow transducers are simply mounted onto the pipe from the outside. Measurement is therefore non-invasive, and no process interruption is necessary for the installation. The transducers are not in direct contact with the medium to be measured and thus in no way submitted to pressure and wear and tear.
All transducer pairs are factory calibrated. All calibration data (including the transducer identification and parameters) is stored permanently in the transducers and is transferred to the transmitter automatically upon connection. This facilitates operation and a zeroing procedure is not necessary.
The user interface is adapted to the detected transducers. The instruments simply asks in a logical sequence for the pipe and medium parameters. The physical properties of a large number of pipe materials and media are stored in an internal data base. The status display enables even the inexperienced user to judge online the quality and precision of the measurement.
|
|
AVFM-II Area-Velocity Flow Meter
Monitor flow through open channels, partially full sewer pipes and surcharged pipes without a flume or weir. Ideal for stormwater, combined effluent, raw sewage, irrigation water and streams.
The AVFM-II uses a submerged ultrasonic sensor to continuously measure both Velocity and Level in the channel. The sensor is a completely sealed ultrasonic unit with no orifices or ports. It mounts inside a pipe or at the bottom of a rectangular, trapezoid or egg-shaped channel. Calibration is simple: enter the pipe diameter or channel width and the AVFM-II computes the flow volume and displays the flow rate.
- For Open Channels and Pipes
- Ultrasonic - Measures Velocity + Level to Calculate Flow
- No Flume or Weir required
- 3 Isolated 4-20mA Outputs (Flow, Level and Velocity)
- Totalizer and 2 Programmable Control Relays
- Simple 3-key Calibration - Password Protected
- Optional Intrinsically Safe Sensor
- Optional built-in 50,000 point Data Logger and Software
|
|
|
The Dynasonics Series 902 portable ultrasonic flowmeter is an excellent tool for measuring liquids containing 25 ppm or more suspended solids or aeration. The instrument also features a 4-20 mA output, rechargeable battery (8 hours continuous operation), and two-line display of rate and total. For full pipes of 1" (25 mm) to 120" (3050 mm) diameter.
|
|
Hot Tap provides accurate flow rate measurement in full and pressurized pipe applications in pipes 18" (460 mm) diameter or larger.
Hot Tap combines ADFM pulse Doppler velocity profiling technology with a unique sensor assembly suitable for insertion into full, operating 18” and larger diameter pipes. It measures flow rate to within ±2% of actual flow rate, even in difficult applications such as installations near bends, short straight runs, near pumps, etc. Applications include:
- Wastewater collection systems
- Combined sewer systems
- Wastewater treatment facilities
- Irrigation canals and channels
- Industrial process
- Stormwater outfalls
|
|
The Heat Calculator Option of FLEXIM's non invasive FLUXUS ADM flow meter allows the easy determination of the energy flow in a system.
With temperature measurements made at the inlet and at the outlet of a system as well as flow measurement at the outlet , FLUXUS calculates the Heat Flow or energy usage within that system. All this is done with temperature and flow measurement devices mounted on the outside of a pipe.
FLUXUS will display the actual heat flow through the system, and if needed, totalize the heat flow in order to obtain the heat quantity.
The values can easily be transmitted to a PC for display and analysis. The data obtained can be used for energy flow balancing or it can be transmitted to a process control system.
|
|
FLUXUS® G709 is an ultrasonic flowmeter for permanent installation in 19" rack systems.
In addition to the flow channels, FLUXUS® G709 can be equipped with up to 4 process inputs. With its wide range of electrical inputs and outputs, it can handle and process a great variety of process parameters.
The integrated flow calculator can perform a standard volume flow or mass flow correction according to ISO 12213-1. The connection of external process pressure and temperature measurements is needed for the calculation.
An extended status display helps the user to judge the measuring situation and current measuring precision directly during the measurement.
|
|
The solution for extreme temperatures
The WaveInjector® enables flow measurement at both very low and very high temperatures (400°C), even in explosion-hazard areas. It offers you the well known advantage of the clamp-on ultrasonic technology: a non-invasive, pressure and medium independant measurement with a high dynamic range and a high flexibility.
No special transducers are needed for the high-temperature measurement. The standard transducers are simply fixed to the WaveInjector®. For very large pipes, a special WaveInjector® version with chains guarantees a robust fixation on the pipe and a high surface pressure on the coupling point.
|
|
Hybrid
Blue-White introduces Sonic-ProTM Hybrid Ultrasonic Flowmeters.
Sonic-Pro has the ability to measure fluid flow using either Doppler or Transit Time methods. Additional features include: Non invasive clamp-on transducers; Custom metric algorithms and DSP technology ensures reliable, accurate measurement; easy reading LCD; data is logged to a standard SD card format supplied with each unit; isolated 4-20 mA output is fully configurable; 0 - 1000Hz Pulse Output is fully configurable; computer connection permits remote access to, and control of, all functions including: real time display, system configuration, data logging, remote data capture and process control functions. Sonic-Pro is IP66.
|
|
Electonic Flow Switch for flow monitoring with ultrasonic sensor, digital display, 2 set points and analog output, linearity error 2,5% m.v.
Features:
7-segment LED dispaly, microprocessor-controlled, self monitoring with error display. All prameteers are configured by keypad, tamper proof, keypad lock, rugged construction, vibration- and shock-proof, long term stability
Applications:
OEM-applications, automotive, automobile industry, cooling
|
|
Series PSX2 Portable Ultrasonic Flowmeter Detector -- Compact and Lightweight
Series PUX Portable Ultrasonic Flowmeter Converter -- Compact and Lightweight
Series PUX2 Portable Ultrasonic Flowmeter Converter -- Data Logging and BTU Capability
Series SX2 Portable Ultrasonic Flowmeter Detector -- Compact and Lightweight
Series SX3 Ultrasonic Flowmeter Detector -- Quick and Easy Mounting
Series UXF1 Ultrasonic Flowmeter Converter -- Excellent Performance and Easy Operation
Series UXF2 Ultrasonic Flow Converter -- Excellent Performance and Easy Operation
Series UXF3 Ultrasonic Flowmeter Converter -- Excellent Performance and Easy Operation
|
|
|
Dynasonics manufactures transit time and Doppler ultrasonic flow meters, in fixed-position, portable and multi-channel versions. These meters are totally non-invasive and easy to install and operate. For clean or dirty liquids, Dynasonics products provide high accuracy measurements on a wide range of pipe materials, diameters and temperatures.
|
|
The FLUXUS ® ADM 5107 ultrasonic flowmeter for permanent installation was designed for the water- and wastewater industry.
The watertight transducers are small and practical, fast to install They are watertight and equipped with fixed transducer wiring. On request, the instrument can be pre-configured at the factory so as to reduce commissioning work to a minimum. Thanks to the clamp-on technology, no cutting or welding work is needed to mount the transducers on the pipe.
|
|
The SONOFLOW sensors, detecting the flow of liquids in thin tubes, constitute a new sensor series for the device automation. The newly developed method serves for a fast and safe identification of the flow rate or the flow volume of liquids respectively. The SONOFLOW is used in the medical technology, automation industry, device- and machine construction as well as in the pharmaceutical plant construction sector.
In order to be able to offer cost-effective flow sensors, we aimed for a modular construction of the measuring cell. It consists of 2 ultrasonic sensors, the metering box and the evaluation electronics. The measuring cell is integrated in the tube.
Due to the use of special inert materials for the measuring cell and the sterile measuring method the system provides great advantages in areas with strict hygienic standards.
Besides standardized applications there is also the opportunity to produce customized SONOFLOW sensors.
|
|
|
|
|
|
Our Innova-Sonic digital liquid flow meters are state-of-the-art universal transit-time instruments incorporating the latest advances in digital signal processing. The Innova-Sonic™ Portable Model 210 clamp-on features an industry-unique Bluetooth® wireless PDA interface for a truly flexible and convenient liquid flow measurement tool. Innova-Sonic™ Model 205 is our dedicated/fixed display readout version with non-invasive clamp-on transducers.
Our Innova-Sonic™ Insertion Model 205 features insertion transducers resulting in high signal strength in challenging applications and extremely large pipes.
While principally designed for clean liquid applications, all instruments in our Innova-Sonic family are tolerant of liquids with small amounts of air bubbles or suspended solids common in most industrial environments. All Innova-Sonic liquid flow meters offer low power consumption, high reliability and outstanding applicability at an economical cost.
UNIQUE PRODUCT FEATURES
- Accuracy better than +/-1%
- Wide operating temperature range -40F to +212F (-40C to 100C) (210 Innov-Sonic)
- One meter for a wide range of pipe sizes 1-200” (25mm-5000mm)
- 256MB Tungsten™ T5 PDA interface with Bluetooth wireless
- Numerical and graphical display interface
- Battery power supply with battery recharge port (including spare battery)
- Low installation effort and costs
- Wide bi-directional Flow range of 0 to 40 fps
-Measurement is independent of fluid conductivity
|
|
|
|
