|
|
|
Dynasonics hybrid ultrasonic flow meters utilize both Doppler and transit time sound techniques and automatically select the correct technology to calculate the flow rate. This dual technology provides an accurate measurement of the volumetric flow of clean, solids-bearing or gaseous liquids on full pipes. Adverse flow conditions - surges, particulate, gas pockets, etc. - will not clog, damage or influence accuracy of the "flow-through" meter design.
|
|
|
Dynasonics TFX Ultra ultrasonic flow and energy meter clamps onto the outside of pipes and do not contact the internal liquid. Available in stand alone flow meter or as an energy flow meter used in conjunction with dual clamp-on RTDs measuring energy usage. Available in integral and remote mount systems, both in a rugged, aluminum enclosure. Reduced material costs, installation time and maintenance costs make this the ideal flow meter for nearly all liquid applications.
|
|
|
The Series TFXL ultrasonic transit time flow meter is a reliable and cost-effective flow meter designed to replace mechanical meters where liquid conditions damage or impede operation. This non-invasive flow meter requires no maintenance, as it clamps on to the outside of the pipe. It provides a 4-20mA analog and simulated turbine meter frequency output, interfacing with a variety of monitoring equipment. The TFXL is available in an integral mount system for pipes size .5" (12mm) to 2” (50mm), and a remote system for pipes size .5" [12mm] and larger.
|
|
|
|
|
|
The battery-powered ultrasonic flowmeter FLUXUS® F601 is an ideal tool for service work and quick control measurements. Its clamp-on flow transducers are simply mounted onto the pipe from the outside and are thus quickly installed, without process interruption.
The measurement is pressure independent and can take place on pipes of almost any materials and on almost any liquid. Transducers are available for pipe diameters from 6 mm to 6500 mm and for temperatures ranging from -40°C to 400°C (more). Two pairs of transducers usually are enough to realize all standard industrial applications. FLUXUS F601 is thus highly flexible and can be used on the most various applications on totally different measuring points.
FLUXUS® F601 has been engineered for the harsh conditions of industrial installations. Its housing is water and dust tight and resistant against oil, many liquids and dirt. The meter and its many accessories are delivered in a sturdy waterproof transport case which dimensions fulfil the airline requirements for carry-on luggage.
Thanks to advanced battery management and Lithium ions battery, F601 allows for more than 14 hours of battery-powered measurement. The remaining battery capacity is displayed and helps planning measuring campaigns realistically.
Beside the standard version, F601 can also be delivered with a wider range of signal inputs and outputs (Multifunctional version), as well as in the Energy version with high precision temperature probes making the energy measurement more powerful than ever.
|
|
KROHNE’s OPTISONIC 6300 stands for continuity and long term reliability. Flow measurement can be done anywhere and start-up is immediate. The new OPTISONIC 6300 clamp-on flowmeter with its robust industrial construction and regreasing concept provides a revolutionary solution for easy handling.
|
|
|
|
|
|
Our Innova-Sonic digital liquid flow meters are state-of-the-art universal transit-time instruments incorporating the latest advances in digital signal processing. The Innova-Sonic™ Portable Model 210 clamp-on features an industry-unique Bluetooth® wireless PDA interface for a truly flexible and convenient liquid flow measurement tool. Innova-Sonic™ Model 205 is our dedicated/fixed display readout version with non-invasive clamp-on transducers.
Our Innova-Sonic™ Insertion Model 205 features insertion transducers resulting in high signal strength in challenging applications and extremely large pipes.
While principally designed for clean liquid applications, all instruments in our Innova-Sonic family are tolerant of liquids with small amounts of air bubbles or suspended solids common in most industrial environments. All Innova-Sonic liquid flow meters offer low power consumption, high reliability and outstanding applicability at an economical cost.
UNIQUE PRODUCT FEATURES
- Accuracy better than +/-1%
- Wide operating temperature range -40F to +212F (-40C to 100C) (210 Innov-Sonic)
- One meter for a wide range of pipe sizes 1-200” (25mm-5000mm)
- 256MB Tungsten™ T5 PDA interface with Bluetooth wireless
- Numerical and graphical display interface
- Battery power supply with battery recharge port (including spare battery)
- Low installation effort and costs
- Wide bi-directional Flow range of 0 to 40 fps
-Measurement is independent of fluid conductivity
|
|
|
|
|
|
Clamp-on ultrasonic flowmeters
The SITRANS F US clamp-on ultrasonic flow technology offers several advantages, number one being the utilization of external transducers. These are quickly and easily mounted on the outside of the pipe, making them the perfect choice for retrofit applications and applications where corrosive, toxic or high pressure liquids and gases rule out the option of cutting the pipe.
With the use of the WideBeam technology, clamp-on flowmeters from Siemens have proven their superiority in both the field and the lab. They offer several benefits such as measurement of practically any liquid and gas; performance unaffected by viscosity, flow rate, pipe size, solids and aeration content; high accuracy and repeatability through automatic temperature compensation and zero drift correction; and installation flexibility on pipe sizes up to DN9140 (360 inches). They are available in six families: two geared towards general industry solutions and four tailored to energy, liquid hydrocarbon, gas and portable installations.
Combine this with flexible configuration options that allow you to either customize your flowmeter or to order complete systems, you can rest assured that we have the right solution for you.
|
|
|
GE Panametrics' GC868 flowmeter is a fixed-installation flowmeter comprised of the GC868 electronics, a pair of advanced clamp-on ultrasonic transducers, a clamping fixture, a preamplifier located near the transducers and coaxial cables to connect the transducers to the preamplifier and GC868 electronics. The DigitalFlow™ GC868 flowmeter can be used to measure the flow of any gas or steam.
|
|
|
The Preso ThermoTrack is a non-invasive ultrasonic flow meter combined with non-invasive temperature sensors, to measure energy use in water-based HVAC systems. No sensors come in contact with the liquid and there are no moving parts, so downtime and maintenance are eliminated. The flow meter utilizes transit time ultrasonic technology and the temperature sensors are Pt1000 RTDs. The flow rate, supply line temperature and return line temperature measurements provide the necessary inputs to calculate energy use, displayed in BTUs, Calories or Watts. The ThermoTrack is available for pipe sizes 1/2" (12 mm) and larger, with a variety of power supply and output options available.
|
|
The MINISONIC P & P-B flowmeters are THE new portable metering tools.
Features include :
- a massive battery life : up to 40 h
- very light weight at 850 g
- Ingress protection IP 67
New measurement technology 'ESC' (or Echo Shape Control), this is an automatic function, essentially an ultrasonic auto-focus, which offers the warranty of quick, sure and accurate flow measurement.
The dual pipe version can calculate, display and transmit a QT flow value equal to the sum or the difference of the two flows that device measures on two independent pipes. It is possible to install the two set of transducers on a same pipe and closed to each other to improve the measurement reliability or better at two different locations and do a line balance or a leak detection.
The portable MINISONIC offer other important advantages :
- measurement resolution < 0.1 ns
- A higher amplification gain range and noise rejection
- an ergonomic keypad and menu calibration, back-lighted display
|
|
|
|
|
|
Clamp-on Ultrasonic Flowmeter with DSP Technology
The MUL-310 is a "Time of flight" type Ultrasonic Flowmeter for liquids. Since the ultrasonic receiver required for the flow measurement is installed by the clamp-on system on the exterior of the pipe, it does not contact the measuring fluid at all, and also there are no concerns about particle generation or contamination of metallic ions in the fluid as it is truly non-invasive. It is suitable for the flow rate measurement of pure water and ultra pure water for the semiconductor industry. The resistance to bubble interference in the signal has been sharply improved by the new signal process method "DSP"(Digital Signal Processor). If bubbles are contained in the fluid, the transmission of the ultrasonic signal is impeded and signal recognition becomes difficult resulting in a loss of signal. Digital Signal Processing technology has been adopted for MUL-310, and even if the bubbles are contained in the fluid, the stable measurement of signal can be achieved. This product does not have limitations in terms of volume of bubbles by air volume being less than 10%. (It is not possible to recognize the signal in case of fluid streams with excessive bubbles)
|
|
Static compact energy meter using ultrasonic technology
highly accurate recording of all billing data in local and district heating and cooling systems
|
|
|
The newcomer in the Ortlinghaus line of products for press drives is our hydraulically actuated form - fit linear motion lock, featuring electronic monitoring. This WORLD NOVELTY is used to lock the press ram regardless of it`s current position and can be integrated into the clutch itself. The activation of the linear motion lock can be implemented into the press control or can be activated by the machine operator from his panel. This easy to operate lock presents a maximum amount of safety for manual work within the area of the ram of presses and is regarded as a vital component for modern on the job safety.
|
|
Actuation
Safety Locks are held open by hydraulic (100 bar min) or pneumatic (3,5 bar min) mean and clamp when pressure drops.
Direction of load
In most applications Safey Locks are mounted on a baseplate, so that the load causes a compressive force to the mounting surface. But if the application requires an upward absorption of the load, a flange for attachment is required as well as a special design of the Safety Lock housing regarding the tensile load.
|
|
Hydraulic heavy load brake:
The Braking and Clamping Element with spring-loaded energy storage KBHS.
The KBHS series is a hydraulically operated heavy load brake featuring spring-loaded energy storage.
This function is based on the toggle lever principle. Pre-tensioned stress bolts provide holding force in case of pressure drop. Here the large-surface contact sections, which are equipped with a special brake lining, are pressed directly onto the free surfaces of the section rail.
At a hydraulic opening pressure of 150bar a holding power of up to 40,0000N is achieved.
The KBHS series features a compact design and is suitable from sizes 35 to 125.
The KBHS series is designed for braking and clamping on linear guides. Because of the material combination of the linear guide/contact section, the linear guide won't be damaged by the contact section
|
|
PClamp clamps and brakes rod loads safely amd quickly. It can be adapted to standard systems such as pneumatic cylinders from leading manufactures (e.g. SMC, Festo= or to individual solutions. Rotatory clamping can also be achieved with PClamp. Certified systems from Employer's Liability Insurance Association can be realised.
Area of application:
Linear rails and guide ways
Clamping of linear axis
Swivel tables
Rotary tables
Spindles, feeders
Rod, piston, spindle clamping
Elevating devices
Hydraulic presses
Hydraulic lifts and elevating tables
Safety catches
Blocking systems
High-lifting devices
|
|
Nexen's RBR-series rail brakes are ideal for clamping and power-off holding applications. The unique piston design allows high clamping forces and low release pressures.
The RBR is engineered for dependable performance, easy set up and low maintenance.
|
|
Active without pressure:
The Clamping and Braking Element including spring-loaded energy storage MB
The MB series is based on a dual-effective wedge slide gear with spring-loaded energy storage for clamping and braking without pressure.
As a specific feature it has three pistons connected in a line.
This arrangement allows use of a stronger spring at 4.5 bar than the BW series does. The stronger spring-loaded storage permits holding forces up to 3,800 N.
The MB series is designed for braking on linear guides.
Because of the material combination of the linear guide/contact section,the linear guide won't be damaged by the contact section.
|
|
Active without pressure – flat design:
The Clamping Element for torque take-up with spring-loaded energy storage TP
The TP series is a pneumatic clamping element for torque motors or for rotational axes.
It works with a newly developed spring-loaded energy storage system.
Torque take-up occurs inside the TP which excludes wear on the driven shaft.
TP achieves high holding torques at a pneumatic opening pressure of >4 bar.
Due to high rigidity, positioning accuracy is exact in use.
The zero maintenance TP is suitable for shaft diameters of
Ø50 to Ø320 mm.
It is characterised by easy assembly and a flat design.
|
|
|
|
|
|
Active without pressure - compact and powerful:
The Clamping and Braking Element with spring-loaded energy storage UB.
The UB series combines the technology of our BW, TK and MB series. The rigid housing and central position of the wedge slide gear achieve very high supporting forces. The mounting hole template enables the BW, TK and MB series to be substituted. The UB series is based on a dual-effective wedge slide gear with spring-loaded energy storage for clamping and braking without pressure.
This arrangement of three pistons connected in a line allows use of a stronger spring at 5.5bar.
The stronger spring-loaded storage permits holding forces up to 9,000 N. Positive fit contact sections mounted within a strong casing guarantee high axial and horizontal rigidity.
The UB series is designed for braking on linear guides. Because of the material combination of the linear guide/contact section, the linear guide won't be damaged by the contact section.
In order to exclude damage from contamination with chips (chips between contact section and linear guide), the elements can be fitted with original seals (seal kit) from the respective linear guide manufacturer and longitudinal seals as accessories.
When used in harsh work environments or with cooling liquid, the seal kit should be used as well.
|
|
The clamping elements react in the shortest possible response time by the patented pneumatic pre-loading of the system of the spring plates in the diaphragm.
These safety systems are permanently operational for the maximum machine protection.
|
|
Mechanical edging grip :
- Lifting power 900kgs
- Maximum holding width from 50 up to 500mm
- Width of jaws 450mm
- Maximum holding depth 170mm
- Automatic system for opening/closing
- Handles for easy handling
- Weight 56kgs
|
|
Manhole Clamp
Simple applying and disconnecting by means of holdfast application: clamp must not be lifted manually
No adjustment of the clamping range
Huge multiplication guarantees optimum safety
One clamp for manholes and cones according to DIN 4034 Part 1 and 2
With spring tension
With web sling or high-strength chains
|
|
Grab for Angular Concrete Products WEZ
Specially developped for handling L-stones and similar products. The lifting eye can be adjusted to the center of gravity of the product being lifted to let it hang vertically.
Standard Specifications:
Lifting eye for attaching to crane hook.
Highly durable and exchangeable rubber grippers.
Automatic release for the fully automatic change over from “full” to “empty”.
|
|
Fork Lift Grab STAZ
Specially designed for heavy duty work with fork lift trucks. Light-weight, yet with a high carrying capacity
due to the use of high-tensile steel for loadbearing parts.
Fully hydraulic parallel opening range.
Low-maintenance steel-polyamide sliding guides.
Standard Specifications:
Manually adjustable pressure relief valve.
Oil Pressure Gauge
Can fit all the usual packs of building materials due to a large opening range and to the exchangeable grippers
which come in various lengths and designs.
Polyamide sliding guides come with a 5 year guarantee.
All Forklift Grabs can also be used as cubing grabs in fully automatic cubers for blocks and pavers.
Besides the hydraulically operated grabs also purely electrically operated grabs can be offered on request.
|
|
|
|
|
|
Block Loading Grabs – with Adjustable Height AKZ-H unigrip / AKZ-N unigrip / AKZ-S unigrip
This has the same design and characteristics like the AKZ-unigrip but comes with adjustable height for differing pack heights. This universal type of grab is suitable for the transport of building materials of all types and sizes. By the adjustable height and the large opening width it can be used for all building materials on pallets and without pallets.
A choice of various heights.
The vertical height adjustment bar is equiped with 4 drillings which are situated on different height levels, each shifted by 90°.
The different levels are for the following heights:
level 1 (turning 0°) 1.100 mm
level 2 (turning 90°) 1.280 mm
level 3 (turning 180°) 1.470 mm
level 4 (turning 270°) 1.650 mm
Height Adjustment with a choice of fixed or floating position.
Now even more simple handling of the height adjustment - just move one lever.
Higher pressure – finely adjustable, for example to grip material which is sensitive against pressure.
Low overall height of equipment.
Standard Specifications:
Hydraulically and smoothly operable and works in parallel.
Robust gear rack balance for the absolute synchronous running of the hydraulic cylinders.
Large low-maintenance polyamide sliding guides with 5-year guarantee.
Automatic pressure control. Carrying capacity of height-adjustable versions in retracted position will be increased as per positive working automatic pressure control up to the respective figure indicated in brackets.
Manually adjustable pressure-reducing valve.
Oil pressure gauge.
4 hanging eyes for cables or straps/belts.
Light-weight construction in high-tensile steel.
|
|
Paver laying and transportation
VM 401 is an innovative, state-of-the-art paver installation machine setting new standards due to its special comfort, high carrying capacity and modular design. Established VM-features such as the robust chassis and the double articulated steering have also been integrated.
A powerful 4-cylinder diesel engine offers sufficient output reserve. The spacious driver's cabin is separated from the chassis and the easy to use joystick operation was improved for driving comfort.
The modular configuration of the cabin and hydraulic system allow for customized equipment matching individual demands, including an optional scratch-resistant safety glass in the driver's cabin.
|
|
Concrete Highway Devider Clamp BSZ-KH
With this mechanical grab barrier walls can begripped absolutely safe without leaving any marks on the concrete elements.
High rationalisation of staff costs.
Rapid repetitive sequences
Standard Specifications:
Lifting eye for attaching to crane hook.
Automatic release for the fully automatic switch over from “full” to “empty”.
Leaves no black marks.
|
|
1504 Kerbstone grip
Ruggen tubular steel construction for the hand-transport and placement of kerbstones, edging blocks and natural stone blocks.
Replaceable rubber gripping surfaces.
Options:
painted
galvanised
|
|
|
|
see the results for the following category : 
