|
|
GIA Utility/Service Truck. Three models are manufactured today i.e. GIA 111 and GIA 211 which is articulated trucks and GIA TT 24 which is a rigid truck. All three models are 4-wheel driven in order to be able to operate in steep inclinations.
The models can be equipped with e.g. boom and basket, scissors platform for ANFO charging, scaling, different kinds of installations and service works. The trucks can also be used as e.g. small dump truck or shotcreting rig. A combination of several equipments on cassettes makes one truck useful in many different applications.
The main feature with GIA Utility/Service Truck is:
• High productivity
• High safety
• Low investment and service cost
• Well known components
|
|
Diesel-powered elevated work platform for safer, more productive overhead maintenance and construction
A-64 scissor lift general features:
* Large, solid, safe elevated work platform for roof-bolting, screening, surveying, cable and vent or water pipe hanging and many other back and rib projects.
* Fully sealed electrical circuits maintain circuit continuity, extend component life and minimize downtime.
* Computer-designed scissor mechanism satisfies structural design standards recognized throughout the world.
* Numerous configurations available for a variety of applications, including a portable palletized ANFO charging system, to meet your specific needs.
|
|
SL-3 Scissor Lift
Designed to provide a safe work platform for installation of services in tunnel headings up to twenty feet (six meters) high. The Mine-Mate™SL-3 Scissor Lift is fully equipped as standard for the multi-tasking required in today’s underground trackless mining environment.
|
|
The RDH All Purpose Scissor Lifts have been designed to exceed the most stringent engineering criteria. With RDH’s solid steel arms we are able to offer a level of safety and durability that has yet to be matched.
The RDH 500N, 500R & 600R are built on the RDH carrier which offers a four wheel drive fully articulated power shift vehicle. The units offer excellent maneuverability with superior handling and good visibility from the cab position. They have been designed with the same criteria as our larger series. These Scissor Lifts make mining safe, productive and cost effective. The complete line of RDH Scissor Lifts can be custom built in order to meet individual requirements.
|
|
Service platforms
AMV Service Platforms are supplied in many configurations. The most popular version is the AMV 10,5. This unit is built on a lorry chassis, it has a maximum working height of the platform floor of 10,5 m. and a lifting capacity of 1500 kg. over the whole working range. It is equipped with four hydraulic support legs. The standard version has a p.t.o. driven hydraulic pump. An electric powerpack can be supplied as an option. Other options are diesel driven compressors and generators for tool operation. All operations are radio operated.
|
|
|
|
|
|
Utilift scissors lifts on our famous mining carrier are designed for lifting and installations in mining and low-profile tunnelling. Utilifts are suitable for roof reinforcement work, charging explosives, hanging cables and installing pipes, ventilation equipment, etc. Typical standard options include a side-shift platform, platform tilt, crane, pipe changing equipment, air compressors, an electric-driven power pack for platform hydraulics, ANFO charging kits and helper platforms. The vehicle’s driving ergonomics can be enhanced with an optional, fully enclosed, high-comfort operator’s cab.
Himecs are the product of long-term collaboration between Normet engineers and global tunnelling customers and experts. This has generated a holistic understanding of customers’ lifting and access equipment needs in both hard and soft rock environments. The wide range of Himecs is ideal for medium to heavy-duty load lifting and work coverage in practically any tunnel profile. With a large variety of platform configurations and standard options, they can be perfectly customized for specific lifting applications. Our new platform load sensing system and other built-in man-lifting safety features comply with the latest safety rules and regulations. Himecs are also CE-approved and feature the famous Normet mining carrier.
|
|
P1 SL6000 Features
Heavy-duty scissor mechanism and deck provide a stable elevated mobile work platform.
Four totally enclosed stabilizers with built-in hydraulic safety locks for leveling machine and higher reach.
6 000 lb or 2 720 kg safe lift capacity.
Proven powertrain with integrated torque converter and three gears in forward and reverse.
Four-wheel totally enclosed wet multi-disc brakes with POSI-STOP feature for emergency/parking.
Articulated heavy-duty frames made to withstand the high impact and torsional stress associated with mining application, frames come with a five-year unlimited guarantee. Large high tensile alloy steel pins located in replaceable anchor bushings
|
|
P1 SLP5000N Features
Heavy-duty scissor mechanism and deck provide a stable elevated mobile work platform.
Compact 6-foot (1,83 m ) wide articulated carrier with 16'-1" (5.13 meter) outside turning radius is extremely well suited for very narrow drifts and confined areas.
Pipe handler system facilitates installation of pipes and ducts.
Four totally enclosed stabilizers with built-in hydraulic safety locks for leveling machine and higher reach.
5 000 lb or 2 268 kg safe lift capacity.
Proven powertrain with integrated torque converter and three gears in forward and reverse.
Four-wheel totally enclosed wet multi-disc brakes with POSI-STOP feature for emergency/parking.
Articulated heavy-duty frames made to withstand the high impact and torsional stress associated with mining application, frames come with a five-year unlimited guarantee. Large high tensile alloy steel pins located in replaceable anchor bushings
|
|
|
|
|
|
Utilift scissors lifts on our famous mining carrier are designed for lifting and installations in mining and low-profile tunnelling. Utilifts are suitable for roof reinforcement work, charging explosives, hanging cables and installing pipes, ventilation equipment, etc. Typical standard options include a side-shift platform, platform tilt, crane, pipe changing equipment, air compressors, an electric-driven power pack for platform hydraulics, ANFO charging kits and helper platforms. The vehicle’s driving ergonomics can be enhanced with an optional, fully enclosed, high-comfort operator’s cab.
Himecs are the product of long-term collaboration between Normet engineers and global tunnelling customers and experts. This has generated a holistic understanding of customers’ lifting and access equipment needs in both hard and soft rock environments. The wide range of Himecs is ideal for medium to heavy-duty load lifting and work coverage in practically any tunnel profile. With a large variety of platform configurations and standard options, they can be perfectly customized for specific lifting applications. Our new platform load sensing system and other built-in man-lifting safety features comply with the latest safety rules and regulations. Himecs are also CE-approved and feature the famous Normet mining carrier.
|
|
PRONAL lifting cushions can be used to lift loads of over 70 tonnes and are particularly useful in areas such as civil protection, security and defence.
They are also used in maintenance operations on construction sites and in various industries for moving, blocking and handling operations... Made from elastomer-coated fabrics, the cushions are vacuum vulcanised at a temperature of 140°C, thus ensuring that they are extremely tough.
Advantages :
- easy to install, thin when empty,
- uniform lifting power,
- high degree of control during lifting, progressive lifting process,
- high lifting force.They are also used for maintenance purposes on site and in industries for some operations as moving, stalling, handling...
|
|
|
If an ECO-Jack toe jack can not be operated, the load can be lifted with an ECO-Jack AIR lifting bag ranging from 1.000kgs (2,200lbs) to 42.000kgs (92,800lbs). Fitting into the tightest areas with a collapsed height of 30mm (1.1-1.2inches), all models are light weighted and equipped with serrated lifting surfaces, markes centers, reinforced edges and safety instructions.
|
|
To be able to achieve a maximum lifting movement with only a minimum insertion space available, lifting bags are the appropriate tools to use. With 12 models, Holmatro has a lifting bag for every job. Thanks to their unique low profile edges the lifting bags can easily be inserted under all circumstances.
The deflated height of our lifting bags is 22 or 25 mm. Using compressed air (maximum 8 bar), the largest model, the HLB 67, reaches a maximum inflation height of 520 mm. Another feature of the lifting bags is their ability to adjust to the lifting surface. The applied pressure is divided over a large surface compared to the use of hydraulic jacks.
|
|
The distinguishing feature of Vetter Mini Lifting Bags 8.0 bar/116 psi is the noiseless, jolt-free, and smooth lifting of the heaviest loads. They lift, push, press, prise and split, even on sloping surfaces. The surface profile improves grip on slippery ground such as grass, sand etetc.
They are produced in two versions. Both versions have a multi-layer construction which covers each side of the bag. This is either steelcord or aramide reinforcement.
|
|
INFLATABLE JACK
1-74 Ton
Highly flexible and lightweight jacks only require an air supply of 8 bar maximum. Any non-explosive gas or water can also be used for inflation.
Uninflated jacks are only 25,4 mm thick, making seemingly impossible lifting tasks routine.
Space age reinforced, multi-layer aramid construction, widely overlapping on all sides. Tested at 8 bar.
In rugged testing, jacks withstood tens of thousands of inflate/deflate cycles at 12 bar.
Large surface area and material flexibility allow jacks to lift loads on soft or ompressible surfaces without support cribbing being necessary.
|
|
Lifting devices
Lifting - Freeing - Cleaving
Mustlift is able to lift safely heavy loads on the ground or in water. Their compact size, allowing to place them quite everywhere, is obtained by a simple vulcanization of a high resistant elastomer coated fabric. They can be used on irregular surfaces thanks to their positive grip surface.
Mustlift lifting bags can be inflated with air or water at maximum 8 bar.
High-pressure flat lifting bag, made from coated fabric (polyester or aramid) vulcalized in one operation. Lifts up to 76 T in the standard range. Anti-slide coating
|
|
for quick application in close space!
- Multi-layer design with Armid material.
- Fill time with 8 bar within seconds.
- Extensive accessories, like suitable case etc.
|
|
Extruded Flat Lift Table
EF1-based, guided cylinder with four shafts for maximum rigidity. It is designed for lifting applications where other non-rotating cylinders cannot handle an overhung load and space is at a premium.
Four-shaft support withstands offset loads and moments.
Simple, efficient design provides economical alternative to other costly guided actuators.
Joins the EF family of products, so shares all the same benefits--long service life, low friction operation, fast delivery.
Convenient wide tooling mounting surface.
Intended for vertical lifting applications (should not be mounted horizontally or with tooling plates facing down).
|
|
For guided lifting and lowering of the workpiece.
The lifting movement is effected power-supported by a hydraulic or electrical actuator against the weight of the workpiece.
The lowering movement is a defined lowering by use of the weight.
For maximum workpiece weights of 100 to 1,000 kg.
Maximum strokes from 200 to 940 mm.
|
|
|
|
|
|
LINAK has launched a wide range of lifting columns to be used in various sectors with the purpose of improving ergonomics at different kinds of workplaces.
LINAK lifting columns allow applications such as
desks
tables
beds
kitchen units and
heavy-duty industrial workbenches
to be raised, lowered or tilted by means of a button. With the LINAK lifting columns it is possible to install sophisticated motorised systems that provide optimum ergonomics at a modest price.
Compared to the lifting columns mentioned, LINAK does manufacture columns used for vertical lift of hospital and care beds where design, easy cleaning and ergonomics are important factors.
LINAKs several different types of lifting columns are for instance LC2, LP2, LP3, DL1, DL2, DL4, DL5 and DL6.
LP2 and LP3 are used in the hospital and care sector for height adjustment of e.g. stretchers, incubators and surgical chairs. The LC2 is a further development of the LP2 and LP3. Besides the applications mentioned above LC2 is also a good choise in more industrial applications.
DL1, DL2, DL4, DL5 and DL6 are part of LINAK's DESKLINE® system for ergonomic sit/stand office desks. DL1, which set the standard of the market, is compact and avaiblable in more colours. The DL2 system offers a progressive speed control, meaning you have the same speed level both upwards and downwards. The DL5 and DL6 are further developing the DL1. DL4 is also called the DESKPOWER™ system.
At the touch of a button the DESKPOWER system can adjust desks within a range of adjustment from 60-125 cm at a high speed level irrespective of load. At the same time the noise level is extremely low.
|
|
Lifting columns are the ideal drive elements when a motor setting is required in addition to the stable guidance. The whole technology is integrated and not visible from the outside. These lifting columns do not need any additional coverings. Usually, no special electrical knowledge will be required for the commissioning. Various versions are available as standard for the application in the field of medical technology.
Several lifting columns can be combined and synchronised and offer further impressive application possibilities. The MultiControl-units can be linked by a BUS-system and enable the synchronization of maximal 32 lifting columns.
|
|
Electric Lifting Columns from LINAK
In the lifting column, the guide and electric linear actuator are integrated. With the electric lifting columns from LINAK it is possible to install the sophisticated motorised system that provides optimum ergonomics in a range of applications. Electric lifting columns from LINAK are designed to raise, lower or tilt:
beds (hospital beds, care beds and home beds)
desks
incubators
industrial workbenches
kitchen units
tables
stretchers
surgical chairs
and more
Lifting columns for hospitals, care, industry, office and home
Some series of electric lifting columns are in particular designed to meet the needs of the hospital and care sectors, the office furniture market, the industry and the comfort furniture market.
|
|
|
|
|
|
LINAK has launched a wide range of lifting columns to be used in various sectors with the purpose of improving ergonomics at different kinds of workplaces.
LINAK lifting columns allow applications such as
desks
tables
beds
kitchen units and
heavy-duty industrial workbenches
to be raised, lowered or tilted by means of a button. With the LINAK lifting columns it is possible to install sophisticated motorised systems that provide optimum ergonomics at a modest price.
Compared to the lifting columns mentioned, LINAK does manufacture columns used for vertical lift of hospital and care beds where design, easy cleaning and ergonomics are important factors.
LINAKs several different types of lifting columns are for instance LC2, LP2, LP3, DL1, DL2, DL4, DL5 and DL6.
LP2 and LP3 are used in the hospital and care sector for height adjustment of e.g. stretchers, incubators and surgical chairs. The LC2 is a further development of the LP2 and LP3. Besides the applications mentioned above LC2 is also a good choise in more industrial applications.
DL1, DL2, DL4, DL5 and DL6 are part of LINAK's DESKLINE® system for ergonomic sit/stand office desks. DL1, which set the standard of the market, is compact and avaiblable in more colours. The DL2 system offers a progressive speed control, meaning you have the same speed level both upwards and downwards. The DL5 and DL6 are further developing the DL1. DL4 is also called the DESKPOWER™ system.
At the touch of a button the DESKPOWER system can adjust desks within a range of adjustment from 60-125 cm at a high speed level irrespective of load. At the same time the noise level is extremely low.
|
|
Light, elegant aluminium profile with a very quit run (<40db)
Are used especially in the medical sector (Ophthalmology, Ultrasound)
Columns of these types can also run in parallel (large tables, ergonomic work)
Big Advantage: Plug and Play
Most of our columns, we call Plug and Play. After receiving the column, attach it to the network power and with the delivered hand switch, you can use the column immediately.
Application: Adjustable chairs and tables, adjustable tables for computer, lecterns and so on
Force: up to 2200 N
Electric current: 230V / 50 Hz
120V / 60 Hz
100V / 60 Hz
Multifunction (all Electric current are possible in one column)
Custom Option: on request
EN 60601-1 certificated
All Materials are recyclable
|
|
| ... products without technical information |
| |
The application needs in practice are so manifold like the bandwidth of the lift gates and lift fields from the HGB GmbH.
Within the different type series widths up to 9.000 mm and lift heights up to 6.000 mm can be realized. Hereby, we especially focus on the aspect of security. An electronic chain breakage monitoring, a connecting block along the closing edge, and a mechanical fall arrester of multiple supporting appliances according to the norm EN 12604 (Appendix B) serve as a safety device in context with the power operated lift gates and lift doors. A complete documentation self-evidently belongs to a complete project perimeter.
|
|
Advantages
Pneumatic clamping with high forces
Optimum safety clamping - if the pneumatic fail the system is locked
The values of hydraulic clamps are reached and exceeded
Low system costs in comparison to hydraulics
Simple installation
Compact design
Wide range for many shaft sizes can be delivered
|
|
The SITEMA Safety Brake type KSP is designed to hold a vertical moved mass in one direction (against gravity). The holding is done on a round shaft. This could be an already existing cylinder rod or a separate rod. The Safety Catcher can also be used to catch the falling load in case of an emergency-stop. The holding force is relatively big in one direction (downwards) and in the other direction (upwards) relatively small.
Safety brakes are already used in the following applications
- vertical or diagonal machine tool axes
- vertical axes of loaders
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
