|
|
RDH 1.25, 2.25 LHD’S
Engine: Deutz BF4L914/BF4M2012C
Transmission: Clark 20000/24000 Series
Carrier: RDH 100/150 Series
Axles: Ford D45N / 14D2149
Electrical: 24 volt
Bucket 1.25: 1.25 yd³ (1 m³)
Bucket 2.25: 2.25 yd³ (1.75 m³)
Options:
Side-dump bucket
Quick dis-connect
|
|
Automated LHD Independent
These vehicles were built, in order to increase within endangered production areas the safety of the personnel.
Because these vehicles are central controlled, the operating time per shift can be increased also within areas with high work temperatures the productivity. A reduction of the personnel cost results from the possibility to control up to three units by one operator at his control desk.
Long distances between loading and unloading can be cover by the vehicle independently.
|
|
The LF-6.3 is the excellent equipment for tunnelling with
minimum drift sizes from 3.0 x 3.0 m. In combination with the
dump truck MK-A20.1 a powerful advance in tunnelling is
guaranteed. The design is special made for rough conditions
and the LF-6.3 convinces with high capacity tramming
|
|
The newly designed SLP12 is a 12 tonne LHD and is the
synonym for productivity and reliability in low profile mines. The
LHD is designed for minimum drift heights of 1.900mm. The
driver’s compartment is made designed for anti fatigue
operations of the driver with high comfort and excellent visibility.
|
|
The newly designed SLP12 is a 12 tonne LHD and is the
synonym for productivity and reliability in low profile mines. The
LHD is designed for minimum drift heights of 1.900mm. The
driver’s compartment is made designed for anti fatigue
operations of the driver with high comfort and excellent visibility.
|
|
The LF-4.5 is a powerful loader for narrow mines with a max.
drift width of 2.5m. This machine is developed for Hard-Rock
mining and tunnelling. It has an excellent performance, due to
of the magnificent dead weight/payload ratio.
|
|
The LF-17/21 is an LHD with a capacity range from 17t up to
21t. One type of chassis is made for three different tonnage
classes. The LF17/21 is specially designed for high productivity
mines and could be operated in hard rock/potash mining.
|
|
The LF-12.3 is the excellent equipment for tunnelling and
mining for minimum drift sizes of 4.0 x 4.0 m. In combination
with the dump truck MK-A30.1 a powerful advance in tunnelling
is guaranteed. The LF-12.3 is designed for application where
high productivity and availability is requested.
|
|
Load Haul Dump Vehicles LT-210
4,500 lbs. (2,041 kg) Rated Load Capacity
1.0 yd³ (0.76 m³) Bucket Capacity
4' - 6" (1372 mm) OA Width
Load Haul Dump Vehicles LT-270
6000 lbs.(2,722 kg) Rated Load Capacity
1.5 yd³ (1.2 m³) Bucket Capacity
4' - 11 15/16" (1523 mm) OA Width
Load Haul Dump Vehicles LT-350
8,000 (3,636 kg.) Rated Load Capacity
2.5 yd³ (1.9 m³) Bucket Capacity
5' - 4 1/8" (1625 mm) OA Width
Load Haul Dump Vehicles LT-650
14,500 lbs. (6,591 kg.) Rated Load Capacity
4.0 yd³ (3.1 m³) Bucket Capacity
6' - 11 1/2" (2121 mm) OA Width
Load Haul Dump Vehicles LT-950
24,000 lbs. (10,909 kg) Rated Load Capacity
7.0 yd³ (5.4 m³) Bucket Capacity
10' (3048 mm) OA Width
|
|
| ... products without technical information |
| |
Electric Vehicle for Waste Collecting ATX200E AR
The ATX E range of Alkè electric vehicles includes the AR version, a special machine equipped with waste collection body, designed for use in cities and towns, sport centres, railway stations, airports, camping sites and tourist villages.
The AR version has a waste collection body built with anti-corrosion aluminium and may be integrated with an optional automatic bin lifting system for 120 and 240 litre bins. The waste body has a 2 cubic metres capacity (410 kg of nominal capacity) with a tipping angle of 90° that allows the waste to be dumped directly into the auto-compacting machines.
|
|
Marrel has extensive experience in designing and producing tipper equipment mounted on industrial vehicles from 3.5 to 32 metric tons.
The Marrel range includes rearside tippers, two-side tippers and three-side tippers suiting customer needs up to the most rigorous uses.
Additional hydraulic functions are available to improve operating conditions.
Marrel's strong reputation is based on the performance and reliability of its products.
The design teams at Marrel meticulously address each and every relevant detail to make its tipper products easier to use.
Product durability is guaranteed through careful material selection (very high tensile steels) and total control of sheet metal working.
|
|
Marrel has extensive experience in designing and producing tipper equipment mounted on industrial vehicles from 3.5 to 32 metric tons.
The Marrel range includes rearside tippers, two-side tippers and three-side tippers suiting customer needs up to the most rigorous uses.
Additional hydraulic functions are available to improve operating conditions.
Marrel's strong reputation is based on the performance and reliability of its products.
The design teams at Marrel meticulously address each and every relevant detail to make its tipper products easier to use.
Product durability is guaranteed through careful material selection (very high tensile steels) and total control of sheet metal working.
|
|
Public Works Tippers
An all aluminium Public Works Tipper that provides the highest payload...
In a constant search for innovation, BENALU proposes his new Public Works Tipper : the Siderale
If your requirements of use lead you to privilege the highest payload to transport materials such as sand, gravel, coal, beets, the SIDERALE will answer your needs perfectly...
Equipped with an aluminium chassis and an aluminium body, the Siderale presents an exclusive, innovative and patented design. Its smooth side walls offer many advantages such as the facility of washing, gasoline (better aero dynamism) and sign writing surface.
Very well equipped, the Siderale is available in volumes from 22 m3 to 26 m3. The Siderale can be equipped with a side rolling cover sheet system or with a longitudinal rolling up on cables.
|
|
With the Astrorunner, BENALU proposes a Public Works Tipper made of aluminum, which design – round and smooth body – is specially thought for the ground transports, sand , gravel, the supplying of power stations or asphalt and finisher, and also for the small and medium demolition.
The smooth side walls of the Astrorunner facilitate the flow of the product and avoid product retention. Its design "half pipe Tipper" is made to get a controlled and centred flow of the product.
With capacities between 22.5 m3 and 24.5 m3, this tipper offers you several advantages like for example the increased resistance to the impacts and to the abrasion, an optimal payloads or an excellent stability obtained thanks to the step frame chassis and a low centre of gravity.
For a better comfort of use, this vehicle is equipped with a pneumatic door unlocking device allowing the protection of the air bags.
On the other hand, its innovating design will facilitate the body cleaning.
|
|
Mega Multitruck Skip Tipper
Equipped with an aluminium skip with a 2m3 capacity, a double lever hydraulic system, tipping to an angle of 90° and a low loading height, that makes loading, unloading and cleaning of the skip very simple.
With a width of 1.4m the MeGA skip tipper can go into the narrowest of streets without compromising the carrying capacity.
The automatic CVT transmission specially developed for small trips provides driver comfort and a reduced maintenance. And because the waste bins are often situated at either side of the road, the flat cabin floor enables the driver to leave the cab from either side.
Silent, the electric version is ideally suited to early morning work and to busy pedestrian streets.
The MEGA skip tipper: loading height of only 1m
Tipping Angle: approx. 90º
Operation Time: < 8 seconds
Electric / hydraulic pump: 12 V - 700 W
Remote switch on lead
High resistance aluminium skip
Access door on right side of skip
|
|
Marrel has extensive experience in designing and producing tipper equipment mounted on industrial vehicles from 3.5 to 32 metric tons.
The Marrel range includes rearside tippers, two-side tippers and three-side tippers suiting customer needs up to the most rigorous uses.
Additional hydraulic functions are available to improve operating conditions.
Marrel's strong reputation is based on the performance and reliability of its products.
The design teams at Marrel meticulously address each and every relevant detail to make its tipper products easier to use.
Product durability is guaranteed through careful material selection (very high tensile steels) and total control of sheet metal working.
|
|
CONTRACTOR TIPPER (fixed panels)
Solid (lengthwise floor runners, all in special E36-3/S355JO breaking point 60kg/mm2, continuous weld), adapted (minimum dead weight, maximum pay load), user friendly (variable distributor controlling raising/lowering from cab), reliable and efficient (large pump flow, double effect compass, sanding before painting), secure (oil temperature and level gauges, quality of hydraulic components)…. What is more, equipped according to the EC NORMS corresponding to the 98/37/EC directive (ram with piloted valve), your security is ensured.
|
|
|
For anyone who works with articulated dumpers, nothing is more important than their vehicles' capacity to go everywhere, no matter what the terrain or weather conditions. The MICHELIN range for articulated dumpers allows you to find the solution best suited to your requirements of mobility and all-purpose operation. Being fitted with MICHELIN tires extends your machines' availability even further and makes them more productive.
|
|
These machines operate in a wide variety of environments: quarries, construction sites and mines. While the conditions in which they are used may vary greatly, the operational requirements remain the same: performance, reliability and cost-effectiveness.
In the MICHELIN range of tires for medium-capacity site dumpers, you are sure to find a solution that is specifically adapted to the conditions in which your vehicles operate. This extensive range is MICHELIN's contribution to the productivity of your machines.
|
|
|
To enhance the competitiveness of mining operations, the payload of rigid dumpers has increased dramatically. MICHELIN innovations, the product of extensive experience in the field, and our ongoing commitment to the customers have always accompanied this increase. The "series 80" concept, for instance, enabled the development of giant dumpers. Backed by this experience, MICHELIN is a partner recognized for its expertise by the major vehicle manufacturers. The entire range of MICHELIN tires for large-capacity site dumpers relies on this expertise. And it is this expertise that MICHELIN makes available to you, to reduce your operating costs.
|
|
|
With the hot-vulcanized retreads for construction vehicle tyres, Rodos provides tyre expertise for standard sizes up to 33" as well for as smaller speciality tyres. Again, quality is also a top priority here. Just as is the case with Schelkmann, Rodos offers application-specific compounds combined with intelligent profiles for optimum tyre solutions. For all Rösler products, it is always the balance of performance, reliability and price that takes centre stage.
|
|
The new radial tyres from Winstone are a logical consequence of Rösler’s retread expertise. Not all carcasses used meet our quality standards. Winstone falls back on new carcasses which are purchased with the highest quality standards applied by European brand manufacturers. Our retread expertise is then applied to the finishing process. Rösler stands for: quality, value for money tyres.
Winstone radial tyres are produced in the sizes 15.5 R25 to 26.5 R25 for various profiles.
|
|
|
|
|
|
Process Solutions manufacturers various types of material handling equipment:
Omega Lifts are our line of stationary lifters and dumpers.
Omega Mover 100-Series are our portable lifters and dumpers.
Omega Mover 1-Series are our pallet jacks, powered pallet jacks and weighing pallet jacks.
Omega Blenders are our drum and bin blenders
In addition, we also can provide the following:
Sanitary hoists/trolley systems.
Hoist attachments.
Fork Lift Attachments
External construction of the various equipment range from Stainless Steel, Painted Steel, Hastelloy, Aluminum, Iconel, Titanium and Polyethylene.
Our material handling equipment can be used with any type of item ranging from drums to bins to bowls, mixers, tanks, or boxes.
Units are available that range from completely manual in operation to units that are fully automated.
Units are available fully manual or powered by pneumatics (90 psi), standard electric (110/208/460/575) or to meet hazardous/explosion-proof environments.
Our equipment is customized to meet your requirements for capacity and functionality.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|
