|
|
|
Our Atlantic Fluidics axial flow liquid ring vacuum pumps are highly efficient and rugged. Their "abuser-friendly" shrouded rotor design allows starting even in a flooded state without fear of damage. Single and multistage pumps are available, capable of achieving ultimate pressures of 4 Torr (5.3 mbar). Close coupled and separate drive configurations are available.
|
|
|
Kinney SDV Dry Screw vacuum pumps operate without any sealing liquid in the pumping chamber. Without metal-to-metal contact inside the pumping chamber, wear is greatly reduced.
|
|
|
KINNEY KLRC liquid ring vacuum pumps are ideally suited for pumping wet mixtures and even slugs of liquid. These rugged vacuum pumps are available in various construction materials such as stainless steel, cast iron, and bronze fitted.
|
|
|
Kinney KC & KTC Series Multi-stage rotary piston vacuum pumps provide pumping speeds of 5-112 CFM (8-190 m³/h) with ultimate pressures of 0.2 milliTorr (0.027 Pa). Our KTC series vacuum pumps include our exclusive triplex piston design to eliminate vibration.
|
|
|
KINNEY rotary piston vacuum pumps provide vacuum levels to 0.2 milliTorr (0.027 Pa) with long operating life. Our triplex piston designs are inherently balanced to eliminate vibration.
|
|
|
Kinney Rotary Vane vacuum pumps provide an economical vacuum source for those applications where the process is relatively clean or filtered. Gas ballast valves for vapor handling applications are included as standard equipment.
|
|
|
Kinney & M-D Pneumatics vacuum boosters from Tuthill Vacuum & Blower Systems provide additional capacity and vacuum range to vacuum pumps.
|
|
|
Engineered Dry Screw vacuum systems incorporate Kinney Dry Screw vacuum pumps into complete vacuum systems with vacuum boosters, custom controls and accessories to combine high pumping speed with deep vacuum levels. Flows range to 10000 CFM (17000 m³/h) with vacuum levels to 10 microns and below.
|
|
|
Our Liquid Ring Vacuum Systems are ideal for pumping wet gas mixtures at low pressures. A wide variety of configurations are available, incorporating Kinney or atlantic fluidics liquid ring vacuum pumps. Performance ranges to 560 CFM (950 m³/h) in standard systems, or to 10000 CFM (17000 m³/h) in Engineered Solution Vacuum Systems.
|
|
|
Booster/Piston vacuum systems combine a rugged, oil-sealed Kinney vacuum pump with a vacuum booster to supercharge the pump, allowing for deeper vacuum or greater throughput. Performance ranges to 2000 CFM (3400 m³/h) in standard systems, or to 10000 CFM (17000 m³/h) in Engineered Solution Vacuum Systems
|
|
|
Kinney Rotary Vane vacuum pumps provide an economical vacuum source for those applications where the process is relatively clean or filtered. Gas ballast valves for vapor handling applications are included as standard equipment.
|
|
|
Allied is the western Canadian representative of dust collection filter bags for Albarrie Canada Ltd. Allied’s Parts Department will specify the bag material and style for specific application. Certain common bag sizes are kept in inventory for emergency supply. Special solutions are offered for difficult conditions such as high temperature, chemical composition and high moisture situations. Albarrie's continuous research and development efforts allow us to offer many unique fabric combinations for effective filtration in a wide variety of challenging applications.
|
|
Sludge Drying
Sludge from paper making and de-inking processes can be efficiently used as a fuel in the energy system of the paper mill if properly dried to improve the energy content. Allied offers complete sludge drying process with rotary dryers and wet precipitators with engineering, supply and installation services
|
|
|
Tuthill Vacuum & Blower Systems supplies its own proprietary lines of lubricants for blowers and vacuum pumps, to keep your blowers and vacuum pumps in top running condition.
|
|
|
Kinney SDV Dry Screw vacuum pumps operate without any sealing liquid in the pumping chamber. Without metal-to-metal contact inside the pumping chamber, wear is greatly reduced.
|
|
|
Catalytic Thermal Oxidizers (CTO) and Regenerative Thermal Oxidizers (RTO) are efficient ways to thermally treat pollutants and volatile organic compounds (VOC). Single valve RTO technology developed by Eisenmann in the 1990’s offers 100% uptime with energy efficiency and guaranteed cleaning results.
|
|
|
Series A Junior is offered in unit sizes 280, 410, 510, 610, 730 and 860 based on a single universal case for each size, giving a high degree of common parts and interchange ability. Units can be mounted in the under driven, over driven and vertical mounting positions and provide a choice of shaft arrangements for either motorised or reducer versions. Motors can be close coupled in various frames and powers.
|
|
|
|
|
|
The Series G helical parallel shaft and bevel helical right angle drive industrial gearbox have been introduced to meet the requirements of today's demanding applications in the medium and heavy-duty sector of the power transmission market. Innovative modular design technology has minimized manufactured part count to maximize availability of product.
Product Specification:
Gear tooth geometry design combines maximum efficiency with high load carrying capacity and minimal noise generation. Serviceability of the product was key in the design of the Series G range allowing easy maintenance for long life and reliability, which are synonymous with our field reputation.
- Unit Sizes: 14, 15, 16, 17, 18, 19, 21 and 22
- Input Power: Up to 1,500 kW (2,000 HP)
- Output Torque: Up to 162,000 Nm (1,433,821 lb.in.)
- Gear Ratios: Up to 315:1 in two stages and up to 70,000:1 in combined form
- Output Shaft:Up to 240mm (9.45 in.)
- Motor Sizes: IEC Frames from 200 to 315; NEMA Frames from 254 to 445
Features & Benefits:
This product takes advantage of our many years of accumulated design expertise together with the use of high quality materials and components, and has the following features & benefits:
- Case hardened and ground helical gears, and hard finished spiral bevel gears have optimised gear geometry to maximise strength and efficiency, and to minimise noise and vibration.
- Horizontal split case design for ease of maintenance.
- Large diameter output shaft and bearings to maximize overhung load capacity.
- Innovative modular construction has minimised part count to maximise availability of product.
|
|
|
Series K3 is a right angle helical bevel helical gear head providing an economical solution for your general automation applications. Built around the high efficiency helical gear and spiral bevel gear technologies developed by our sister company David Brown the Series K3 will provide you with complete flexibility in design.
|
|
|
Our worm gear drives have a compact design with high torque capacity. Series BS can be sold as a gearbox or complete geared motor. These units have proven very reliable in tough applications again and again.
|
|
|
This range is offered in 3 basic unit types. Under-driven worm, over-driven worm and vertically mounted with output shaft. The units provide power capacity up to 839 kW in 6 sizes from size 10 to size 24 with worm gear centres from 254mm to 609mm. All are offered with a choice of 14 standard ratios from 5:1 to 70:1. Motorised versions of all units are also available.
|
|
The Series M geared motor has been developed with many years of design proficiency which results in a series of speed reducing geared motors offering high load carrying capacity, high efficiency, quiet running and reliability.
Product Specification:
Series M in line geared motors and reducers can meet a wide range of engineering demands offering a very efficient and compact drive solution offering input power up to 90Kw and a maximum output torque capacity of 11,000 Nm.
- Unit Sizes: 01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 13, 14
- Input Power: Up to 90kW (121HP)
- Output Torque: Up to 11,000Nm (97,350 lb.in)
- Gear Ratios: 1.2 to 8:1 single reduction, 1.4 to 70:1 double reduction, up to 250:1 triple reduction 16,200:1 in combined units
- Motor Sizes: IEC Frames from 63 to 280; NEMA Frames from 56 to 405
|
|
Series C Right angle helical worm geared motors and reducers provide a highly efficient and compact solution to meet most requirements up to 45 kW with maximum output torque capacity of 10,000Nm.
Product Specification:
The Series C product adds to the growing family of new drives which has taken advantage of our many years of accumulated design expertise, together with the use of high quality materials and components. The end result is a series of speed reducing and geared motors offering high load carrying capacity, increased efficiency, quiet running and reliability.
- Unit Sizes: 03, 04, 05, 06, 07, 08, 09, 10
- Input Power: Up to 45kW (60HP)
- Output Torque: Up to 10,000Nm (88,500 lb.in)
- Gear Ratios: From 8:1 to 250:1 in a double unit and 60,000:1 in combined units
- Motor Sizes: IEC Frames from 63 to 225; NEMA Frames from 56 to 326
|
|
The units are also available with rubber torque bushes, output flanges, output shafts and KIBO® sleeves to allow for trouble free maintenance. All variants can be fitted with standard IEC motors. Input shaft assemblies are available up to and including F10.
* Unit Sizes: 02,03,04,05,06,07,08,09,10,11,12
* Input Power: Up to 110kW (147HP)
* Output Torque: Up to 16,500Nm (146,000 lb.in)
* Gear Ratios: From 5:1 to 100:1 in double reduction form and in combined unit form up to 5,600:1.
* Motor Sizes: IEC Frames from 63 to 225
|
|
The Series K geared motor is designed with integral cast feet for base or end mounting and can be offered with single or double extended output shafts. Units are also available shaft mounted or with output flanges and are available for mounting horizontally or vertically. The units can also be offered with a bolt on torque reaction bracket and all variants are available either motorised or with an input shaft assembly.
* Unit Sizes: 03, 04, 05, 06, 07, 08, 09, 10 and 12
* Input Power: Up to 90 kW (121 HP)
* Output Torque: Up to 12,300 Nm (109,000 lb.in.)
* Gear Ratios: Up to 160:1 in three stages, 10,000:1 in five stages, and 36,000:1 in six stages
* Motor Sizes: IEC Frames from 63 to 280; NEMA Frames from 56 to 405
|
|
Maag Pump Systems gear pumps are displacement pumps for high pressure environments. Their performance and long lifespan increase the efficiency of your manufacturing plant. They are used in diverse processes as feed, reactor discharge and booster pumps for low and high-viscosity applications.
The new extrex® 70-5 HV gear pump has a maximum ∆p of 200 bar and a 25% higher specific volume due to its wider gear design. The new extrex® gear pump is also available in models such as HP for ∆p up to 400 bar, RB for rubber processing, and the standard GP for regular extrusion process applications.
|
|
|
Maag Pump Systems gear pumps are displacement pumps for high pressure environments. Their performance and long lifespan increase the efficiency of your manufacturing plant. They are used in diverse processes as feed, reactor discharge and booster pumps for low and high-viscosity applications.
|
|
Maag Pump Systems Textron builds its gear pumps to a modular design that adapts easily to customers’ requirements and industrial standards.
Housings are available in iron, steel or stainless steel, with or without heating jackets. Bearings, shafts and gears offer a similarly wide choice of materials and configurations.
Five classes of axial clearance and eight classes of radial clearance, coupled with Maag’s expertise in simulation, allow individual pumps to be specified for the highest possible efficiency. A wide choice of seals ensures safety in demanding applications.
|
|
|
“Wall Mounted Mechanical Filter Units are constructed for the use at fixed welding workingplaces, in welding cabins and training shops. It can be easily mounted to the wall or a pillar or a console. It is constructed with very strong steel sheet and painted with powder paint durable to stroke and scratch. Airflow is suctioned by acrobat arms and reversed into the media as purified with a %99,9 filter efiiciency through of 4 stages filter equipment.
|
|
Notes:
1. Element diameter is 63.5 mm with cover.
2. Pressure drop calculations based on 20 micron elements.
3. Element length is for mesh pack and does not include end fitting.
4. Polymer viscosity is 250 Pas (2500 Poise).
5. Design conditions are 241.5 Bar (3500 psi) and 343.5C (650F).
6. Vessel material is 304SS and system is designed per ASME Code.
7. System configuration is MPST's patented close-coupled design.
8. System includes manual vent valves and hydraulically automated diverter valves with control panel.
9. System prices are Ex Works Maag Factory.
Options Available:
A. Actuated Vent Valves
B. Drain Valves (manual and actuated)
C. Plunger and spool valves available upon request
|
|
|
|
see the results for the following category : 
