|
|
The EcoDry M incorporates a dry sliding mechanism without the need for oil or hydrocarbons.
Through the further developed and optimised compression processes, the EcoDry M 15/30 attains with three compression stages a base pressure (total) in the low 10-2 mbar range.
Since the EcoDry M 15/20/30 may be operated either vertically (as normally delivered) or horizontally, this pump is highly flexible when it has to be integrated into the customer’s system.
Advantages to the User
Low maintenance, free of oil and bearing lubrication, free of hydrocarbons
Extremely low particle emissions on the intake and exhaust sides
Rugged and most reliable
Low power consumption
Service friendly
Air cooling
Plug & play
Good pumping speed at low base pressure
High water vapour tolerance (gas ballast standard)
No grease lubricated bearings in the vacuum section
Leak tight
Compact size
Runs at 1000/1200 rpm (50/60 Hz mains)
Rugged full cross section exhaust valves
For both horizontal and vertical operation
Typical Applications
Applications in physics
Loadlock chambers
Transfer chambers
Mass spectrometers
Electron microscopes
Lighting
Thinfilm coaters
Freeze drying
Forevacuum pump for dry high-vacuum systems
Pumping of oxygen concentrations over 21 percent by volume upon request
|
|
|
Kinney KC & KTC Series Multi-stage rotary piston vacuum pumps provide pumping speeds of 5-112 CFM (8-190 m³/h) with ultimate pressures of 0.2 milliTorr (0.027 Pa). Our KTC series vacuum pumps include our exclusive triplex piston design to eliminate vibration.
|
|
Advantages to the User
Gas ballast facility
Easy maintenance
Good ultimate pressure with and without gas ballast
High pumping speed at low intake pressures
Compact design with flange mounted motor
High water vapor tolerance
Reliable continuous operation
Tolerant and rugged, due to non-contact rotary piston within the pump chamber
Very smooth operation due to dynamically balanced masses
Separate oil filling for the gear protects the gear against contaminated pump oil
Oil is used for sealing, lubrication and cooling
A built-in anti-reverse lock prevents incorrect rotation of the piston and also stops it being pulled back when the pump is switched off while under vacuum
Air cooling makes the pump environmentally- friendly and economic
Clear design and service-friendly due to the modular design
Typical Applications
Chemical, metallurgical and electronic vacuum processes
Impregnating, degassing and drying process-es in experimentation systems, in drying cabinets, extrusion etc.
Pressure range down to 4 x 10 E-2 mbar (2.4 x 10-2 Torr) without gas ballast or to 5 x 10 E-1 mbar (3 x 10 E-1 Torr) with gas ballast
Backing pump for Roots vacuum pumps at intake pressure down to 10 E-3 mbar (0.75 x 10 E-3 Torr)
Supplied Equipment
With DN 65 DIN flanges on the intake and exhaust sides for direct connection of DN 63 ISO-K flange components
Ready for operation, complete with oil filling
Special models for different motor voltages, motor frequencies and other protection class ratings are available - Details on these upon request
|
|
|
KINNEY rotary piston vacuum pumps provide vacuum levels to 0.2 milliTorr (0.027 Pa) with long operating life. Our triplex piston designs are inherently balanced to eliminate vibration.
|
|
These small rocking piston pumps are specifically designed for a very wide range of applications (dentistry, medical devices, hobbies and light industry). The design structure requires the installation of the pump in safe environments. Before starting up the unit, the user must make it compliant with the specific product directives (only within EU).
Standard supply includes:
- Shock mounts
- Silencer
- Thermal circuit breaker (140°C)
|
|
Shelf Dryers
Vacuum Shelf Dryers
The Edwards range of Vacuum Shelf Dryers provide rapid drying of heat sensitive, air sensitive, pyrophoric, and other materials that require drying without agitation or oxidation. Utilizing a fully sealed vacuum chamber and heated shelves, the Vacuum Shelf Dryers offer the ideal solution for batch drying of delicate materials.
|
|
|
Booster/Piston vacuum systems combine a rugged, oil-sealed Kinney vacuum pump with a vacuum booster to supercharge the pump, allowing for deeper vacuum or greater throughput. Performance ranges to 2000 CFM (3400 m³/h) in standard systems, or to 10000 CFM (17000 m³/h) in Engineered Solution Vacuum Systems
|
|
| ... products without technical information |
| |
For the dosing of liquid chemicals, Alltech Dosieranlagen GmbH has developed the piston diaphragm metering pumps of the FKM series.
These metering pumps meet the highest requirements in operational reliability and accuracy.
Alltech piston diaphragm metering pumps are built in a modular concept. This guarantees high flexibility in combining the pump elements for various areas of applications.
By using different materials and designs for the liquid end, Alltech metering pumps may be used for the dosing of almost all kinds of chemicals.
To find an optimal solution for your dosing tasks, we offer various dosing capacities and pressure ranges.
The integrated pressure relief valve guarantees maximum security.
A wide range of accessories (stroke actuators, pulsation dampers e.g.) completes the range of our production.
|
|
The MultiFertic® injection pump are heavy duty, high precision pumps for chemicals products and additives, made up of one driving module and 1 to 4 injection modules for 25 to 500 l/h. - 7.5 to 150 GPH
In the same injector can be connected several injection modules to apportion different products (INDEPENDENT INJECTION) or to increase the injection flow. By increasing the number of modules in the same injector, a higher flow regularity is obtained, whereby in the 4 modules model an actually continuous flow is obtained.
|
|
|
For corrosive and abrasive media, which have to be dosed against higher pressures than 16 bar piston pumps can be fitted with a piston-diaphragm system. The KMS system combines the advantages of leakage-free diaphragm dosing pumps and precise piston dosing pumps and thus ensures reliable dosing.
|
|
Reliability and accuracy: the elaborate combination
High dosing accuracy and exact reproducibility of the dosing flow. The deviations in dosing flow constancy and linearity are below 2%.
High degree of functional safety by standardised diaphragm breakage system and overpressure valve.
The pumps can be universally employed due to the full Teflon dosing diaphragm and optimum material combinations of the parts in touch with the media.
Very easy adjustment of the dosing flow: the dosing flow can be adjusted accurately, even if the system is not running.
|
|
Reliability and accuracy guarantee optimum process safety:
High dosing accuracy and exact reproducibility of the dosing flow. The deviations in dosing flow constancy and linearity are below 1%.
High degree of functional safety by standardised diaphragm breakage system, overpressure valve and vent valve of the hydraulic system.
The pumps can be universally employed due to the full teflon dosing diaphragm and optimum material combinations of the parts in touch with the media.
Very easy adjustment of the dosing flow: the dosing flow can be adjusted accurately, even if the system is not running.
|
|
Reliability and accuracy: the elaborate combination
High dosing accuracy and exact reproducibility of the dosing flow. The deviations in dosing flow constancy and linearity are below 2%.
High degree of functional safety by standardised diaphragm breakage system and overpressure valve.
The pumps can be universally employed due to the full Teflon dosing diaphragm and optimum material combinations of the parts in touch with the media.
Very easy adjustment of the dosing flow: the dosing flow can be adjusted accurately, even if the system is not running.
|
|
Piston pumps are precise and – compared to diaphragm dosing pumps – almost pressure-independent metering units. The flow rate changes in proportion to the stroke length and can thus be adjusted to very small values. Fields of application are – among others – process engineering and chemical processes, i.e.: wherever the medium must be metered precisely.
The FEDOS E / DX piston dosing pumps from Lutz-Jesco are available at flow rates between 0.17 and 31.5 l/h, with or without microprocessor control. Depending on the size of the pump, maximum pressures between 30 and 200 bar are admissible.
If no control is required for constant metering, the motor is connected directly to the terminal box. In this case, FEDOS E pumps are used. To change the flow rate, either the stroke length can be adjusted mechanically, or the speed of the motor is controlled by means of a separate frequency converter.
FEDOS DX pumps are used if an integration in controls or automatic control systems is requested.
FEDOS DX pumps allow the adaption to a large number of different control systems and system monitoring equipment. The signals required for the external avtivation of the pump can be simple voltage-free closing contacts from water meters or controllers or analog 0(4)...20 mA signals.
|
|
GENERAL SPECIFICATIONS
/- 1% Steady State Accuracy over a 10:1 Turndown (w/constant speed drive)
Continuous Duty / Severe Service Design
Polar Crank Drive Design
Rugged Cast Iron Gear Housing
Modular Design
Multiplex Capability
Variable Stroke Length (non-last motion)
Integral Pressure Lubrication System
Double Ball Check Valves
Pressures up to 10,000 psig (690 bar g)
Flows up to 1,225 gph (4,637 lph)
Meets API Standard 675
|
|
| ... products without technical information |
| |
For the dosing of liquid chemicals, Alltech Dosieranlagen GmbH has developed the piston diaphragm metering pumps of the FKM series.
These metering pumps meet the highest requirements in operational reliability and accuracy.
Alltech piston diaphragm metering pumps are built in a modular concept. This guarantees high flexibility in combining the pump elements for various areas of applications.
By using different materials and designs for the liquid end, Alltech metering pumps may be used for the dosing of almost all kinds of chemicals.
To find an optimal solution for your dosing tasks, we offer various dosing capacities and pressure ranges.
The integrated pressure relief valve guarantees maximum security.
A wide range of accessories (stroke actuators, pulsation dampers e.g.) completes the range of our production.
|
|
The MultiFertic® injection pump are heavy duty, high precision pumps for chemicals products and additives, made up of one driving module and 1 to 4 injection modules for 25 to 500 l/h. - 7.5 to 150 GPH
In the same injector can be connected several injection modules to apportion different products (INDEPENDENT INJECTION) or to increase the injection flow. By increasing the number of modules in the same injector, a higher flow regularity is obtained, whereby in the 4 modules model an actually continuous flow is obtained.
|
|
|
For corrosive and abrasive media, which have to be dosed against higher pressures than 16 bar piston pumps can be fitted with a piston-diaphragm system. The KMS system combines the advantages of leakage-free diaphragm dosing pumps and precise piston dosing pumps and thus ensures reliable dosing.
|
|
Reliability and accuracy: the elaborate combination
High dosing accuracy and exact reproducibility of the dosing flow. The deviations in dosing flow constancy and linearity are below 2%.
High degree of functional safety by standardised diaphragm breakage system and overpressure valve.
The pumps can be universally employed due to the full Teflon dosing diaphragm and optimum material combinations of the parts in touch with the media.
Very easy adjustment of the dosing flow: the dosing flow can be adjusted accurately, even if the system is not running.
|
|
Reliability and accuracy guarantee optimum process safety:
High dosing accuracy and exact reproducibility of the dosing flow. The deviations in dosing flow constancy and linearity are below 1%.
High degree of functional safety by standardised diaphragm breakage system, overpressure valve and vent valve of the hydraulic system.
The pumps can be universally employed due to the full teflon dosing diaphragm and optimum material combinations of the parts in touch with the media.
Very easy adjustment of the dosing flow: the dosing flow can be adjusted accurately, even if the system is not running.
|
|
Reliability and accuracy: the elaborate combination
High dosing accuracy and exact reproducibility of the dosing flow. The deviations in dosing flow constancy and linearity are below 2%.
High degree of functional safety by standardised diaphragm breakage system and overpressure valve.
The pumps can be universally employed due to the full Teflon dosing diaphragm and optimum material combinations of the parts in touch with the media.
Very easy adjustment of the dosing flow: the dosing flow can be adjusted accurately, even if the system is not running.
|
|
HydraCell piston diaphragm pumps are very compact and low-maintenance. By their almost pulsationsfreie and run-calm mode of operation differ this poetryless pumps substantially from conventional pump systems.
The most promotion and dosing tasks are mastered by rotary pumps, multi-level centrifugal pumps, Exenterschneckenpumpen or diaphragm metering pumps only with a very small efficiency.
VERDER HydraCell pump does not only supply to you with an efficiency of over 80%, but is also a economical alternative to well-known reciprocating and rotary pump systems. The high efficiency our VERDER HydraCell pumps is the crucial factor for the small life cycle costs (LCC).
|
|
| ... products without technical information |
| |
|
|
see the results for the following category
