|
|
|
Engineered Dry Screw vacuum systems incorporate Kinney Dry Screw vacuum pumps into complete vacuum systems with vacuum boosters, custom controls and accessories to combine high pumping speed with deep vacuum levels. Flows range to 10000 CFM (17000 m³/h) with vacuum levels to 10 microns and below.
|
|
The combination of oilfree chemistry diaphragm pumps with roots pumps allows for a pumping unit series with greatly increased pumping speed and an ultimate vacuum that is improved by one order of magnitude in comparison to diaphragm pumps. VACUUBRAND roots pumping units distinguish themselves with high specific corrosion-resistance. Due to the dry, oilfree operation and high pumping speed especially in the pressure range of 50 - 0.2 mbar the roots pumping units can pump large quantities of vapour.
VARIO roots pumping units have automatic workload-dependent motor speed control. This allows for operation also at high pressure levels (> 50 mbar) with limited heat release.
|
|
The units of HYDROSYS series consist of a liquid-ring vacuum pump of our series TRH, TRS, TRM, TRV, of an air-liquid cyclone separator, of a heat exchanger, all units being mounted on one compact frame.
Several accessories are available to meet particular requirements of plant, of process and of maintenance, and furthermore, it is possible to design particular units, upon request, in co-operation with our Sales Office.
The HYDROSYS series can also be used to work as a compressor up to a maximum pressure of 2 bar, higher than the suction pressure by using tanks and accessories according to ISPESL standards.
|
|
|
Our Liquid Ring Vacuum Systems are ideal for pumping wet gas mixtures at low pressures. A wide variety of configurations are available, incorporating Kinney or atlantic fluidics liquid ring vacuum pumps. Performance ranges to 560 CFM (950 m³/h) in standard systems, or to 10000 CFM (17000 m³/h) in Engineered Solution Vacuum Systems.
|
|
|
Booster/Piston vacuum systems combine a rugged, oil-sealed Kinney vacuum pump with a vacuum booster to supercharge the pump, allowing for deeper vacuum or greater throughput. Performance ranges to 2000 CFM (3400 m³/h) in standard systems, or to 10000 CFM (17000 m³/h) in Engineered Solution Vacuum Systems
|
|
General description
HINDHIVAC manufactures three models of Direct Driven Vacuum Roots Blowers model RD 150, RD375, RD 500 and RD 1450.
These Roots Pumps are compact with a very advanced impeller design for operation at maximum differential pressure around 60 m.bar. These Roots Pumps are ideal for use in Industrial Vacuum Systems where high degree of pumping speed and ultimate vacuum are desired.
Roots Pumps are specially balanced on dynamic balancing machines to ensure vibration free running at high RPM's. The perfect functioning of the roots pump with a favorable compression ratio of 1:3 & 1:10 depending upon the conditions can be achieved by selecting suitable backing pump.
|
|
|
ANVER TT Series Transfer Tubes instantly provide air movement the moment compressed air is applied and their transfer speed and output flow can be infinitely adjusted by regulating the input pressure. Made from aluminum with a durable anodized finish, they come in a wide variety of bore sizes from 0.375” to 1” (9.5 to 25.4 mm) I.D., with air flows from 15 to 145 SCFM.
|
|
|
Electric and Compressed Air Powered Vacuum Pumps, Vacuum Generators and Vacuum Stations, Vacuum Valves and Switches, Vacuum Filters and Exhaust Mufflers, Air Movers and Transfer Tubes, and a wide range of Vacuum System Accessories, all available at competitive prices.
|
|
|
Our Atlantic Fluidics axial flow liquid ring vacuum pumps are highly efficient and rugged. Their "abuser-friendly" shrouded rotor design allows starting even in a flooded state without fear of damage. Single and multistage pumps are available, capable of achieving ultimate pressures of 4 Torr (5.3 mbar). Close coupled and separate drive configurations are available.
|
|
The Benefits of SIHI dry at a Glance
PERFORMANCE
• Range m160 up to m1000
• Suction Volume:- 160 to 1000 m3/h
• End Pressure < 1 to < 0.01
LOW LIFE CYCLE COSTS
• No need for service liquids:-
- totally dry principle of operation
- no gears for rotor syncronisation
- no waste disposal
• Low energy cost:-
- reduced power consumption
• Wear free:-
- non contacting rotors
- no mechanical shaft seals
- electronic rotor synchronisation
- no rotor coatings
QUIET
• No gear box
ROBUST and RELIABLE
• For wet processes
- vertical, self draining
- no stagnant ares in pump casing
- liquid carry-over/flushing capability
• For tough operating conditions
- optimised rotor clearance
- torque monitoring
- liquid flushing during operation
- cleaning without dismantling pump
• For explosive gases
- low internal gas temperature
- Ex-rating
- explosion proof design
- ATEX certified
• For thermally sensitive substances
- optimum temperature / compression profile
- uniform temperature profile
|
|
|
Kinney SDV Dry Screw vacuum pumps operate without any sealing liquid in the pumping chamber. Without metal-to-metal contact inside the pumping chamber, wear is greatly reduced.
|
|
|
|
|
|
The comprehensive Sterling SIHI range of liquid ring vacuum pumps is available in single and two stage designs, with suction capacities up to 12000 m3/h and suction pressures in the range 33 to 1013 mbar. In addition, above atmospheric pressure these pumps can be used as compressors.
SIHI FULL RANGE PERFORMANCE
Capacity - 12,000 m3/h
Suction pressures - 33 to 1013 mbar
The latest addition to this is the SIHI LPH-X range, which is available in one and two stage variants and able to operate at 50Hz and 60Hz.
It has been designed for interchangeability with the well established LPHA range and offers the lowest cost of ownership.
SIHI LPH-X PERFORMANCE
Single stage:- Suction pressures - 120 to 1013 mbar
Suction volume flow - 50 to 850 m3/h
Two stage:- Suction pressures - 33 to 1013 mbar
Suction volume flow - 44 to 800 m3/h
FEATURES
• Interchangeable with previous LPH range
• Complies with ATEX legislation
• Single and two stage
• Modular construction
• Compact design
• Fewer components
• Extensive range of sizes, materials and
sealing combinations
• Seal accessibility
• Engineered systems
|
|
|
KINNEY KLRC liquid ring vacuum pumps are ideally suited for pumping wet mixtures and even slugs of liquid. These rugged vacuum pumps are available in various construction materials such as stainless steel, cast iron, and bronze fitted.
|
|
|
Kinney KC & KTC Series Multi-stage rotary piston vacuum pumps provide pumping speeds of 5-112 CFM (8-190 m³/h) with ultimate pressures of 0.2 milliTorr (0.027 Pa). Our KTC series vacuum pumps include our exclusive triplex piston design to eliminate vibration.
|
|
Sterling Service has more than 200 specialised service centres around the world. These are supported by a network of manufacturing centres and 50 wholly owned sales operations. All of this ensures the highest level of service is provided to our customers at a local level.
WHATEVER THE SOURCE OF YOUR ORIGINAL VACUUM EQUIPMENT - STERLING SERVICE SUPPLIES THE SOLUTION FOR YOUR PUMPS & COMPRESSORS.
- Replacement vacuum pumps
- Replacement compressors
- Emergency breakdown cover Repair
- Extended warranty
- Refurbishment
- Service contracts
- Original spare parts
- On-site service
- Re-engineering
- Commissioning-
- Installation
|
|
|
KINNEY rotary piston vacuum pumps provide vacuum levels to 0.2 milliTorr (0.027 Pa) with long operating life. Our triplex piston designs are inherently balanced to eliminate vibration.
|
|
|
Kinney Rotary Vane vacuum pumps provide an economical vacuum source for those applications where the process is relatively clean or filtered. Gas ballast valves for vapor handling applications are included as standard equipment.
|
|
The Kavac series of vacuum products includes a wide variety of conventional vacuum components, as well as more specialised items such as variable vacuum pumps, material transfer and air amplification units. KV's vacuum division is also able to deliver customer-specific vacuum solutions; often developing customised pumps or completely integrated vacuum control systems. A comprehensive range of vacuum cups complements the Kavac range.
|
|
| ... products without technical information |
| |
Series 750/760 - Consistent Pressure Booster Systems
Features:
- Completely assembled and prewired for easy installaion
- Compact design allows unit to be moved thru standard 30" doorways
- Pressure sensing control panel has been specifically designed by Aurora pump for pressure boosting applications
- Pressure reducing valves automatically reduce higher inlet pressure to a constant downstream pressure regardless of changing flow rate or inlet pressure
- Feature Aurora Pump Model 342A vertical centrifugal end-suction pumps in bronze fitted construction
- Galvanized piping for corrosion resistance.
|
|
|
|
|
|
ALTI-NEXIS V/VE and N-ALTI V/VE
BEACH Of USE:
Flow: 360 m3/h
HMT: 240 mCE
APPLICATIONS:
Clear water overpressure for the following applications:
- Maintenance with constant pressure of the high pressure networks water supply subjected to variation of flow
- Water conveyance and overpressure (drinking water or slightly chlorinated)
- Agriculture, horticulture, aquiculture (Irrigation, washing...)
- Systems of cleaning, washing in industry
- Water supply industrial
ADVANTAGES:
Modular systems compact from 2 to 4 vertical pumps, preset and ready to be installed
Very top-outputs hydraulics and engine (EFF1 out of standard)
Total pressure loss of the booster (valves, valves, collectors...) lower than 2,5mCE
Quiet valve between supports (pressure loss of only 0,7mCE), drainer on pressure gauge
Easy disassembling of the valves (without having to move back piping)
Collectors aspiration and stainless 304 repression (out of request 316 or galvanized)
Adjustable antivibratory studs
Order and protection gathered in the cupboard which ensures the integral automatism of operation: cascade, permutation, lack of water
Choice of the type of cupboard: electronics advanced (CE+), electromechanics managed by programmable automat (CA) or with variable speed transmission (CV)
|
|
| ... products without technical information |
| |
These hydraulic pump units are for the closed circuit lubrication of special machines.
They are tailor-made to designs developed with the design offices of our industrial clients.
The CMtec positive-displacement pump carries the lubricant in a closed circuit between the machine to be lubricated and the oil sump of the lubrication unit. The assembly forms a self-contained unit that may be mobile.
These units are fitted with :
· Closed oil sump
· Filler breather
· Suction tube with oil strainer
· Visual level indicator with thermometer
· Motor-pump unit
OPTIONAL EXTRAS
· Air cooler
· Filtration system
· Heated tube
· Pressure control gauge
· Other tailor-made options available on request
|
|
The Lubeplus GX is ideally suited to mechanical applications and plant used in the food processing, packaging and printing industries. Can accommodate systems with up to 200 lubrication points.
Lubeplus GX is designed to operate with Positive Dsplacement Units (PDU) or with Metering Flow units . The lubricator is available with a wide combination of condition monitoring features and a choice of 'with' or 'without' microprocessor control.
Gear Pump operation
Max. operating pressure 25 bar
Can pump Oil or fluid grease
Available in 3 or 6 litre reservoirs.
Supply voltages 110v or 240
|
|
The New HDI Product Range - suitable for medium to large machine tools, fixed plant in quarries, steel works, coal mines, cement works and large cranes where a choice of lubricant from SAE 90 oil to NLGI grade 2 grease is required.
The Progressive Grease pump is an electrically operated pump, supplied with a 12/24v DC Internal controller with external digital display, which can be fitted with up to three pumping units. Available with 3, 6 ,9 and 15 KG reservoirs, delivering precise amounts of lubricant through progressive distribution blocks, providing the user with lubrication point versatility and reliability.
Progressive HDI Pump
Pumps Lubricants including and up to Heavy Grade 2 greases
Delivery pressure: 350Bar Maximum
Output: 4.2cc per minute per outlet.
|
|
| ... products without technical information |
| |
These 150 to 200 hp power units have hydraulic flows from 70 to 90 GPM (265 to 340 LPM). These units will drive our high performance submersible pumps and other hydraulically driven equipment. We offer skid frame and trailer mounted units with diesel engines or electric motor drives. Shown here are many of our standard models. If you need a custom power unit with features or performance other than standard, please contact us with your requirements.
Standard engines Deutz and John Deere.
Electric drive models available on request.
Hydraulic flows up to 340 lpm (90 gpm).
Hydraulic pressure up to 170 bar (2,500 psi).
Available with either fixed gear or variable piston hydraulic pumps.
|
|
These portable hydraulic power units have hydraulic flows from 1 to 10 GPM (4 to 38 LPM). These units will drive our smaller submersible pumps and also power most hydraulic tools on the market today. We offer portable units with gas (petrol) engines, diesel engines and electric motor drives. Shown here are many of our standard models. If you need a power unit with features or performance other than standard, please contact us with your requirements.
Engine fuel diesel and gasoline
Fuel tanks up to 56 liters (15 gallons)
Hydraulic flow up to 38 lpm (10 gpm)
Horsepower up to 15 horsepower
Hydraulic pressures up to 142 bar (2,100 psi)
Custom configurations including twin circuits and other pressure and flow combinations are available.
Available with electric start and optional wheel kit.
|
|
The mid-size units shown here have hydraulic flows from 25 to 55 GPM (95 to 208 LPM). These units will drive most of our contractor, municipal and industrial submersible pumps. We offer skid frame and trailer mounted units with diesel engines and electric motor drives. Shown here are many of our standard models. If you need a power unit with features or performance other than standard, please contact us with your requirements.
Available with John Deere and Deutz engines.
Electric powered units available.
Hydraulic flows up to 200 lpm (53 gpm).
Hydraulic pressure up to 170 bar (2,500 psi).
Available with fixed gear or variable piston hydraulic pumps.
Custom twin circuit and other flows and pressure configurations are available.
|
|
|
|
see the results for the following category : 
