|
|
Available in double-acting and spring-return configurations The RC range is an extremely compact pneumatic actuator. Its scotch yoke design is particularly suited for valves with high start or end torque requirements. With torque output up to 4,400Nm (38,700 lbf-in)
The RC200 range is available in a variety of configurations and an extensive range of options and accessories is available.
|
|
|
|
|
|
Description standard features
• intermittent duty S4 / S5 min.25% duty cycle, 1200c/h
acc. to DIN EN 60034, protection class IP67
• motor insulation class F, temp. range -20°C to +60°C
(-4°F to +140°F)
• „non intrusive“ for PROFITRON (after adjustment of the
end positions of the valve)
• hand wheel for emergency operation (disconnected
during normal operation)
• PROFITRON: 3 reference force-stroke of the valve can
be stored
• electronic motor protection, automatic phase sequence
correction
• frequency range of the power supply 47 to 63 Hz
• 24 V DC supply for electronics unit possible
• analog actual position value (0/4...20mA)
• travel limits continuously adjustable
• force dependent cut-off adjustable in 10% steps from
70% to 100% Fmax.
• travel speed adjustable in 7 steps,
step-up distance factor 1.4
• self-acting cut-off (depending on cut-off force, travel
distance, etc.)
• soft starting for high positioning accuracy (starting
current less then rated current)
• indication that actuator is in operation
• separate mounting of the electronics unit possible
• external screws stainless steel
• documentation in German/English: operating instructions
• programming by customer possible
|
|
Modulating actuator 2SB6...
• Force 2 to 25 kN
• Stroke 10 to 100 mm
• positioning speeds 13,5 to 50 mm/min
Standard design
• intermittent duty S4 min. 30% duty cycle max 600 c/h
S5 min. 30% duty cycle max 600 c/h
• optional: short-time duty S2-2 min for open-loop control
• duty acc. DIN VDE 0530, part 1
• Temperature range –20 to +60°C
• Protection class IP 65 acc. to DIN 40050 / IEC529
• hand wheel for emergency operation (disconnected
during normal operation)
• preloaded belleville springs to maintain the closing force
->Minimum axial driving rod vibration in case of
unfavorable flow conditions in the valve
• double-acting, coercive controlled, load dependant
tripping in the end positions and the stroke
->Damage protection for the valve in case of eg.g debris
between the valve seat and the valve trim
• absolute self-locking of the driving rod
• optional position electronics
|
|
Standard actuators 2SC50.. 150 to 4300 Nm
Modualting actuators 2SC55.. 250 to 3400 Nm
Positioning speed ranges: 20 to 160 sec/90°
Mechanical connection: ISO 5211, base & lever
For torques exeeding the standard ranges, combinations of 2SA5 rotary actuators and larger
worm gearboxes are utilized (up to 360,000 Nm).
SIPOS 5 Flash
• Integrated frequency converter
• Upgradeable functionality
• Valve protection
• High positioning accuracy
• Variable positioning times
• Modular design
• minimal type variance
|
|
The Skilmatic range is a self-contained electro-hydraulic valve actuation solution available for both quarter-turn and linear applications. The actuators incorporate sophisticated electronics that provide non-intrusive set-up and interrogation via an infra-red hand held remote. They are suitable for on/off, modulating and emergency shutdown duties in applications up to SIL 3.
•Linear thrust output 1.7 to 5500kN.
•Quarter-turn torque output 65 to 600,000Nm.
•Single-, three-phase or 24Vdc power supply options.
•Non-intrusive infrared setting & configuration.
•LCD display for position, pressure, diagnostics and fault indication.
•Optional bus communications via all major protocols.
•Partial stroke test capability.
•Watertight or explosionproof.
•Double-sealed terminal compartment.
•ATEX, FM, CSA, IEC and GOST certified.
|
|
Actuators
Pneumatic and motorized actuators for quarter turn and linear valves (butterfly valves, ball valves, diaphragm valves, gate valves), complete control actuators available, field bus connection and integration into automation systems available
|
|
|
Electric linear actuators, also called thrust drives, are mostly applied to automate globe valves. They are also suitable for the operation of butterfly valves with lever arrangements. AUMA linear actuators consist of the combination of a multi-turn actuator SA and a linear thrust unit LE.
|
|
|
AUMA multi-turn actuators of the type SA operate reliably in various industries worldwide for OPEN-CLOSE as well as modulating service. One of the main applications lies in the automation of gate valves and globe valves. A multitude of further applications are possible in combination with valve gearboxes (worm, bevel and spur gearboxes).
|
|
|
The increasing importance of part-turn valves for automation also reflects in AUMA’s range of products. The further development of the reliable SG type range and the newly developed AS type range with integrated electronic controls VARIOMATIC offer customers a multitude of possibilities to integrate actuators into the process control system/DCS.
|
|
The RC range is an extremely compact pneumatic actuator. Its scotch yoke design is particularly suited for valves with high start or end torque requirements. It is available in double-acting and spring-return configurations with torque output up to 4,400Nm (38,700 lbf-in).
The RC200 range is available in a variety of configurations and an extensive range of options and accessories is available.
|
|
type ST 0
Max. load thrust: 4 000 [N]
Switching-off thrust: 4 500 [N]
Operatings speed: 4 to 40 [min-1]
Operating stroke: 8 to 40 [mm]
Ambient temperature: -25 to +55 [°C]
Protection enclosure: IP 54 (67)
Operating position: any position
Weight: 2,5 to 4,5 [kg]
Standard equipment
· Voltage 230 V AC
· Terminal board connection
· Control part executions:
o 1 thrust switch + 1 position switch
o 2 thrust switches
· Pillar mechanical connection
· Mechanical position indicator
· Manual control
|
|
|
|
|
|
PNEUMATIC ACTUATOR EB-EW, SINGLE-ACTING
FEATURES
- Maintenance-free, continious lubrication
- Suitability for valves with an angle of 90°
- Blow-proof shaft bearing
- Torques in agreement with EN ISO 5211
- Control pressure min. 2 bar, max. 10 bar
- Good visible elastic position indicator
- Function return by turning the supply plate:
Currentless - close
Currentless - open
- All elements of connection are made of stainless steel.
Possibilities of mounting and accesories are shown in chapter 4.3.
GENERAL APPLICATIONS
- Water and wastewater technology
- Shipbuilding
- Swimming pool technology
- Bulk handling
- Pneumatic conveying systems
- Chemical industry
TECHNICAL DATA
Torque: 35-1368 Nm (control air pressure 6 bar)
Final position: adjustable to +/- 3°
Limit switch and solenoid
valve mounting: VDI / VDE 3845
Control pressure: min. 3 bar, max. 10 bar
Control air: clean and dry air
at circuits $ 2/min please lubricate
Temperature range: - 20/+85 °C
Valve interface: EN ISO 5211
Actuator cylinder: Aluminium, hard anodized.
Other coatings upon request.
|
|
New in 2008, the J3 Series part turn electric rotary valve actuators from J+J, the leaders in actuator innovation, introduces an LED status light in the cover to give continuous visual status information advising if the actuator is functioning correctly, is in manual mode, or has stopped because the valve is blocked.
The J3 also offers plug & play function conversion kits to change the standard on-off function to either failsafe or modulating, or both.
|
|
type SP 1
Max. load torque: 80 [Nm]
Switching-off torque: 90 [Nm]
Operating time: 10 to 80 [s/90°]
Operating angle: 60° to 360°
Ambient temperature: -25 to 55 [°C]
Protection enclosure: IP 65
Operating position: any position
Weight: 6,5 to 8,3 [kg]
Standard equipment
¤ Voltage 230 V AC
¤ Terminal board connection
¤ 2 torque switches
¤ 2 position switches
¤ Mechanical stop ends
¤ Connection with valve flanged ISO 5211
¤ Mechanical position indicator
¤ Manual control
Additional equipment
¤ Voltage 24 V AC, 24 V DC, 3x400 V AC
¤ Connector connection
¤ 2 additional position switches
¤ Position transmitter with the following type of signal:
- resistive 1x100 [ohm], 1x2000 [ohm], 2x100 [ohm], 2x2000[ohm]
- current from R/I converter 4 to 20 [mA] with/without power supply
- current (a capacitive transmitter) 4 to 20 [mA]
¤ Position controller 0/4 to 20 [mA], 0 to 10 [V]
¤ Space heater
¤ Space heater's thermal switch
¤ Electric local control
¤ Version with stand
¤ Version with lever
¤ Pull-rod
|
|
|
Electro-hydraulic valve actuators for positional, modulating and stepping control of globe, choke, plug, gate, ball, and butterfly valves, for hazardous areas and severe environments, these can be self contained with their own power packs and tank systems or be fitted into an existing hydraulic ring main circuit.
|
|
|
|
|
|
Actuators (90° quarter turn actuators) for ball valves and butterfly valves, explosion proof
Electrical, explosion proof quarter turn actuators series ExMax and RedMax, for ball valves, butterfly valves and mixing valves, from 5 Nm to 100 Nm, in acc. with ATEX 94/9/EC for installation in hazardous areas zone 1, 2, 21 and 22, for all kind of gas, vapours, mixtures and dust. Actuators with or without fail safe spring return function. 24 to 230 VAC/DC multivoltage supply, 5 motor running times adjustable on site, on-off, 3-pos, 0...10 VDC, 4...20 mA mode, 100 % overload protected. Robust aluminium housing with IP 66 protection, optional stainless steel version, integrated heater for use from -40°C to +40°C/+50°C, cable connection, approx. 1 m cable, manual override, squared shaft connection 12 × 12 mm (size S) and 16 × 16 mm (size M). Series ExMax-... for use in zone 1, 2, 21 and 22. Series RedMax-... for use in zone 2 and 22. Optional accessories like external adaptable aux. switches, terminal boxes and mounting brackets available. Adaptations for all typical quarter turn valves available.
|
|
Honeywell’s HercuLine® 2000 series actuators are low-torque (50 to 400 lb-in), precision electric actuators incorporating all of the easy-to-use, high-quality and reliable features of traditional HercuLine actuators, ensuring processes operate at maximum efficiency with minimal downtime and lowest lifetime cost. They are industrial rated and engineered for very precise positioning of dampers and valves. They perform especially well in extremely demanding environments requiring continuous duty, high reliability and low maintenance.
HercuLine 2000 series actuators incorporate all of the high quality and reliable features of the traditional HercuLine actuators with the added benefits of a microprocessor-based Enhanced Electronics Unit (EEU). These benefits make it easier to set up and maintain the actuator and allows the customer to monitor the health of the actuator for proactive maintenance planning
|
|
-Explosion Proof linear Actuators with spring return
-Explosion Proof linear Actuators without spring return
-Torque: 800-1000-1600-2000 up to 40000N
-For globe valves
-Power Supply from 24V AC up to 240V AC
-On-Off, 3 Point, Modulating- MFT Multifunction Technology
-Spindle stroke self-adjusting
-Several valve adapter available
-Suitable for zone 1,21
-II 2GD EEx d IIC T6
-IP54
|
|
Explosion-proof linear electric actuator ST 1-Ex
Technical data
Max. load thrust: 8 700 [N]
Switching-off thrust: 10 000 [N]
Operating speed: 8 to 80 [min-1]
Operating stroke: 8 to 80 [mm]
Ambient temperature: -25 to +55 [°C]
Protection enclosure: IP 54
Operating position: any position
Weight: 11 to 15 [kg]
Standard equipment
# Voltage 230 [V] AC
# Terminal board connection
# 2 thrust switches
# 2 position switches
# Space heater
# Space heater's thermal switch
# Local position indicator
# Flange mechanical connection
* substitution pillar version
# Manual control
Additional equipment
# Voltage 24 [V] AC
# 2 additional position switches
# Position transmitter with the following type of signal:
* resistive 1x100 [ohm], 1x2000 [ohm]
* current from R/I converter 4 to 20 [mA] with/without power supply
* current (a capacitive transmitter) 4 to 20 [mA]
# Position controller 0/4 to 20 [mA], 0 to 10 [V]
|
|
Explosion-proof multi-turn actuator MO 5-Ex
Technical data
Max. load torque: 600 [Nm]
Switching-off torque: 250 to 1000 [Nm]
Operating speed: 15 to 100 [min-1]
Number of revolutions: 1 to 150
Ambient temperature: -20 to +55 [°C]
Protection enclosure: IP 55
Operating position: the motor axis should be in horizontal position
Weight: 110 to 130 [kg]
Standard equipment
# 3x400 [V] AC - Terminal board connection
# 2 torque switches
# 2 position switches
# 2 additional position switches
# Space heater with thermal switch
# Flange mechanical connection
# Mechanical position indicator
# Manual control
# switching-off from torque blocking
|
|
Explosion-proof part-turn electric actuator SP 2-Ex
Technical data
Max. load torque: 125 [Nm]
Switching-off torque: 145 [Nm]
Operating time: 5 to 80 [s/90¡Æ]
Operating angle: 60¡Æ to 360¡Æ [¡Æ]
Ambient temperature: -50 to +40 and -25 to +55 [¡ÆC]
Protection enclosure: IP 54
Operating position: any position
Weight: 16 to 16,5 [kg]
Standard equipment
# Voltage 230 [V] AC
# Terminal board connection
# 2 torgue switches
# 2 position switches
# 2 additional position switches
# Space heater
# ¬´hermal switch
# Mechanical stop ends
# Connection with valve flanged ISO 5211
# Manual control
Additional equipment
# Voltage 3x400 [V] AC, 24 [V] AC, 24 [V] DC
# Position transmitter with the following type of signal:
* resistive 1x100 [§Ù], 1x2000 [§Ù], 2x100 [§Ù], 2x2000 [§Ù]
* current from R/I converter 4 to 20 [mA] with/without power supply
* current (a capacitive transmitter) 4 to 20 [mA]
# Position controller 0/4 to 20 [mA], 0 to 10 [V]
# Version with stand
# Version with lever
# Pull-rod
|
|
-Explosion Proof rotary Actuators without spring return with torque from 10Nm up to 4500Nm
-For ball valves
-Power Supply from 24V AC up to 240V AC
-On-Off, 3 Point, Modulating
-Auxiliary switches
-Suitable for zone 1,21,2,22
-II 2GD EEx d IIC T6
-IP66
|
|
Electric ATEX explosion proof Oden P30 actuator for linear or turning control valve applications.
High precision through the Oden Gear System.
Fits most types of valves using ASAB standardised modules and assembly kits
Voltage 24 VDC
Analogue control 4-20 mA
Speed 400 mm/min
Linear Force up to 24 kN
Turning Torque up to 30 Nm (added gear up to 4500 Nm)
|
|
Valve actuators, explosion proof
Electrical, explosion proof linear motion actuators series ExRun, RedRun (NEW from I. quarter 2009) and ExVent, for valves and other linear motion armatures , from 500 N to 10.000 N, in acc. with ATEX 94/9/EC for installation in hazardous areas zone 1, 2, 21 and 22, for all kind of gas, vapours, mixtures and dust. Actuators with or without fail safe spring return function. 24 to 230 VAC/DC in acc. to type, 5 motor running times adjustable on site, on-off, 3-pos, 0...10 VDC, 4...20 mA mode, 100 % overload protected. Robust aluminium housing with IP 66 protection, integrated heater for use from -40°C to +40°C/+50°C, integrated Ex-terminal box, manual override. Series ExVent and ExRun-... for use in zone 1, 2, 21 and 22. Series RedRun-... for use in zone 2 and 22. Optional accessories like external adaptable aux. switches, terminal boxes and mounting brackets available. Adaptations for all typical linear valves available.
|
|
type MO 3
Max. load torque: 120 [Nm]
Switching-off torque: 150 [Nm]
Operatings speed: 10 to 63 [min-1]
Number of revolutions: 1 to 380
Ambient temperature: -40 to 55 [°C]
Protection enclosure: IP 55 (65)
Operating position: the motor axis should be in horizontal position
Weight: 26,5 to 29,5 [kg]
Standard equipment
¤ Voltage 3x400 V AC
¤ Terminal board connection
¤ 2 torgue switches
¤ 2 position switches
¤ Space heater
¤ Flange mechanical connection
¤ Local position indicator
¤ Manual control
¤ Torque switches blocking in limit position
Additional equipment
¤ Voltage 3x380 V AC
¤ 2 additional position switches
¤ Position transmitter with the following type of signal:
- resistive 1x100 [ohm], 2x100 [ohm]
- current from R/I converter 4-20 [mA] with/without power supply
- current (a capacitive transmitter) 4-20 [mA]
¤ Position controller 0/4 to 20 [mA], 0 to 10 [V]
¤ Electric local control
¤ Mechanical connection with connect adapter
|
|
IMPACT 2000ª is a high integrity modular pneumatic actuator controlassembly in 316 Stainless Steel. Lighter, stronger and more compact than panel mounting. IMPACT 2000ª offers a significant reduction in total installed cost in both CAPEX and OPEX over panel mounted assemblies.
The modular system does away with comple arrangements using panels, pipes and additional fittings. Using a range of field proven components, valves, spool, poppet or direct acting, and filter regulators are connected in series using a universally compatible interface block and mounted directly onto the valve actuator.
|
|
Series 700 actuators are pneumatic diaphragm operators that offer spring return in either direct or reverse acting styles, offering fail-open and fail-closed modes respectively.
The actuators may be fitted with a variety of springs in order to overcome the wide range of forces that may exist on a valve plug. An adjusting mechanism is incorporated into the actuator design to allow for adjustment of the spring pre-compression.
The series 700 actuator is available in 60, 100 and 160 square inches of effective diaphragm area and may accommodate up to five inches of travel.
|
|
Double acting actuors PETRAS
Double acting pneumatic actuators up to 10 000 Nm at 5 barg supply pressure.
rotation : 90° - 120° -180° - 240°
Materials
- high grade aluminium
- cast iron
- carbon steel
- stainless steel
Hydraulic version available up to 200 barg supply pressure
Established in 1966, PETRAS is a pioneer in the design and manufacture of high performance pneumatic and hydraulic actuators for quarter turn valves.
|
|
Electric Oden P30L, P50L and P220L control valve actuators for linear applications.
High precision through the Oden Gear System.
Fits most types of valves using ASAB standardised linear modules and assembly kits
Voltage 24 VDC.
Analogue control 4-20 mA or digital.
Force up to 40 kN.
Standard stroke 40/100
|
|
Part-turn Actuator AVAT/AVATM01 - AVATM06 are installed on the automation of ball valves and butterfly valves.
Part-turn Actuator AVAT/AVATM01 - AVATM06 can be combined with lever if it is required.
Part-turn Actuator AVAT01 - AVAT06 torque range is from 125Nm to 2000Nm (90ft-lbf to 1475ft-lbf)
·Voltage Supply: 220Vac ~ 460Vac, 50Hz/60Hz, single or three phase.
·Enclosure Protection: IP68, Double-seated structure.
·Isolation: Class F, Class H (optional)
·Optional Function:
Modulating I/O signal 4-20mA
Explosion Proof
Fieldbus System: Modbus, Profibus, etc.
|
|
|
|
