|
|
Double motor actuator M76348
Torques: 750, 1500 or 3000 Nm
• with control and high-speed motor
Speeds: Modulating for 5 or 10 rpm
High speed for 20 or 40 or 80 rpm
• mode of operation to DIN VDE 0530, Part 1,
in closed-loop control operation: intermittent duty
S4/S5 -10%ED - 1200c/h for control motor < 3 kW
S4/S5 -10%ED - 600c/h for control motor > 3 kW
in high-speed operation: short time duty S2 – 5 min
• hand wheel for emergency operation
• mounting flange and drive shaft, type D to DIN 3210
(free end shaft with featherkey)
• Temperature range –20 to +60°C
• self-locking
|
|
type ST 0
Max. load thrust: 4 000 [N]
Switching-off thrust: 4 500 [N]
Operatings speed: 4 to 40 [min-1]
Operating stroke: 8 to 40 [mm]
Ambient temperature: -25 to +55 [°C]
Protection enclosure: IP 54 (67)
Operating position: any position
Weight: 2,5 to 4,5 [kg]
Standard equipment
· Voltage 230 V AC
· Terminal board connection
· Control part executions:
o 1 thrust switch + 1 position switch
o 2 thrust switches
· Pillar mechanical connection
· Mechanical position indicator
· Manual control
|
|
Description standard features
• intermittent duty S4 / S5 min.25% duty cycle, 1200c/h
acc. to DIN EN 60034, protection class IP67
• motor insulation class F, temp. range -20°C to +60°C
(-4°F to +140°F)
• „non intrusive“ for PROFITRON (after adjustment of the
end positions of the valve)
• hand wheel for emergency operation (disconnected
during normal operation)
• PROFITRON: 3 reference force-stroke of the valve can
be stored
• electronic motor protection, automatic phase sequence
correction
• frequency range of the power supply 47 to 63 Hz
• 24 V DC supply for electronics unit possible
• analog actual position value (0/4...20mA)
• travel limits continuously adjustable
• force dependent cut-off adjustable in 10% steps from
70% to 100% Fmax.
• travel speed adjustable in 7 steps,
step-up distance factor 1.4
• self-acting cut-off (depending on cut-off force, travel
distance, etc.)
• soft starting for high positioning accuracy (starting
current less then rated current)
• indication that actuator is in operation
• separate mounting of the electronics unit possible
• external screws stainless steel
• documentation in German/English: operating instructions
• programming by customer possible
|
|
Modulating actuator 2SB6...
• Force 2 to 25 kN
• Stroke 10 to 100 mm
• positioning speeds 13,5 to 50 mm/min
Standard design
• intermittent duty S4 min. 30% duty cycle max 600 c/h
S5 min. 30% duty cycle max 600 c/h
• optional: short-time duty S2-2 min for open-loop control
• duty acc. DIN VDE 0530, part 1
• Temperature range –20 to +60°C
• Protection class IP 65 acc. to DIN 40050 / IEC529
• hand wheel for emergency operation (disconnected
during normal operation)
• preloaded belleville springs to maintain the closing force
->Minimum axial driving rod vibration in case of
unfavorable flow conditions in the valve
• double-acting, coercive controlled, load dependant
tripping in the end positions and the stroke
->Damage protection for the valve in case of eg.g debris
between the valve seat and the valve trim
• absolute self-locking of the driving rod
• optional position electronics
|
|
New in 2008, the J3 Series part turn electric rotary valve actuators from J+J, the leaders in actuator innovation, introduces an LED status light in the cover to give continuous visual status information advising if the actuator is functioning correctly, is in manual mode, or has stopped because the valve is blocked.
The J3 also offers plug & play function conversion kits to change the standard on-off function to either failsafe or modulating, or both.
|
|
type SP 1
Max. load torque: 80 [Nm]
Switching-off torque: 90 [Nm]
Operating time: 10 to 80 [s/90°]
Operating angle: 60° to 360°
Ambient temperature: -25 to 55 [°C]
Protection enclosure: IP 65
Operating position: any position
Weight: 6,5 to 8,3 [kg]
Standard equipment
¤ Voltage 230 V AC
¤ Terminal board connection
¤ 2 torque switches
¤ 2 position switches
¤ Mechanical stop ends
¤ Connection with valve flanged ISO 5211
¤ Mechanical position indicator
¤ Manual control
Additional equipment
¤ Voltage 24 V AC, 24 V DC, 3x400 V AC
¤ Connector connection
¤ 2 additional position switches
¤ Position transmitter with the following type of signal:
- resistive 1x100 [ohm], 1x2000 [ohm], 2x100 [ohm], 2x2000[ohm]
- current from R/I converter 4 to 20 [mA] with/without power supply
- current (a capacitive transmitter) 4 to 20 [mA]
¤ Position controller 0/4 to 20 [mA], 0 to 10 [V]
¤ Space heater
¤ Space heater's thermal switch
¤ Electric local control
¤ Version with stand
¤ Version with lever
¤ Pull-rod
|
|
Standard actuators 2SC50.. 150 to 4300 Nm
Modualting actuators 2SC55.. 250 to 3400 Nm
Positioning speed ranges: 20 to 160 sec/90°
Mechanical connection: ISO 5211, base & lever
For torques exeeding the standard ranges, combinations of 2SA5 rotary actuators and larger
worm gearboxes are utilized (up to 360,000 Nm).
SIPOS 5 Flash
• Integrated frequency converter
• Upgradeable functionality
• Valve protection
• High positioning accuracy
• Variable positioning times
• Modular design
• minimal type variance
|
|
RACO's turn and part-turn valve actuator is a completely electromechanical final control element for operating fittings, valves and flaps, etc. with rotational movement ranging from less than 1 revolution to several revolutions.
The DM IV is assembled from components of the same proven building block system from RACO's electric actuators. This allows us to offer every customer the special turn and part-turn valve actuator for his needs at a low price.
The DM IV consists of the gear, motor and accessories.
|
|
Standard 2SA50.. 10 to 4000 Nm
Modulating 2SA55.. 15 to 2800 Nm
Speed ranges 1,25 bis 160 1/min
mechanical connection DIN ISO 5210 oder
DIN 3210
SIPOS 5 Flash
• Integrated frequency converter
• Upgradeable functionality
• Valve protection
• High positioning accuracy
• Variable positioning times
• Modular design
• minimal type variance
|
|
- Model Number : 72014284216
- Product Name: AVA06(AK35)
- Remarks: 380V 3Phase 50HZ
Output Speed(RPM):18/24/36/48/72/96/144
Rated Torque(Nm):650/650/540/454/430/350/235
Motor poles:4/4/4/2/2/2/2
Rated Output(Amps):5.4/6.8/8.6/9.2/12.5/12.5/12.5
Rated Output power(KW):1.12/1.49/1.78/1.9/2.7/2.7/2.7
(33%Wrated Load):
Current Amps:3.1/3.1/3.3/3.9/4.3/4.4/4.5
Power Factor:0.89/0.89/0.92/0.91/0.96/0.96/0.96
Locked Rotor(Amps):25/25/25/36/36/36/36
Weight:75/75/75/75/75/75/75
|
|
AUMA offers a range of actuators meeting virtually any valve automation requirement. A wide range of multi-turn actuators from 10 Nm through 32,000 Nm, part-turn actuators from 25 Nm to 360,000 Nm or linear actuators from
3,8 kN to 217 kN are available.
Various types of valves can be operated by rotation, swivel and linear movements.
|
|
EAU Series
For use with Ball Valves up to 2"
Series EVR
For use with all sizes of Ball Valves and Butterfly Valves up to 4"
Series EJM
For use with all sizes of Ball Valves and Butterfly Valves up to 24"
Series EVS / EVT
For use with all sizes of Ball Valves and Butterfly Valves up to 12"
|
|
J+J are first to market in their class with the new J3 Series IP65 weatherproof reversible part-turn electric actuators, introducing an LED light in the cover to provide continuous visible actuator status information, and with different flash sequences, provides simple and instant fault diagnosis. Also a first, is the function conversion kits which retro-fit to covert on-off function to either failsafe or modulating, or both.
The features compliment the retained functionality from the J2 Series actuators including multi-voltage capability and electronic torque limiting with auto gear relaxing, which were firsts in 2003 when the J2 was launched
|
|
Actuators for ball valves and butterfly valves, explosion proof
Electrical, explosion proof quarter turn actuators seriess ExMax and RedMax, for ball valves, butterfly valves and mixing valves, from 5 Nm to 100 Nm, in acc. with ATEX 94/9/EG for installation in hazardous areas zone 1, 2, 21 and 22, for all kind of gas, vapours, mixtures and dust. Actuators with or without fail safe spring return function. 24 to 230 VAC/DC multivoltage supply, 5 motor running times adjustable on site, on-off, 3-pos, 0...10 VDC, 4...20 mA mode, 100 % overload protected, robust aluminium housing with IP 66 protection, optional stainless steel version, integrated heater for use from -40°C to +40°C/+50°C, cable connection, approx. 1 m cable, manual override, squared shaft connection 12x12 mm (size S) and 16x16 mm (size M). series ExMax-... for use in zone 1, 2, 21 and 22. series RedMax-... for use in zone 2 and 22. Optional accessories like external adaptable aux. switches, terminal boxes and mounting brackets available. Adaptations for all typical quarter turn valves available.
|
|
The EXNM is a compact actuators. These are intended for the operation of:
-air control damper in ventilation and air condition systems up to approx 2mq.
Features:
Weight: only 4Kg
Mode operating:3Point or Modulating
3 point operating: The actuator moves the damper to its working position until it is powered. If the power supply is interrupted the motor locks the damper position.
Modulating operating: Just powered, the actuator moves the damper to its start position, then it moves to the position set by the control signal.
If the control signal is interrupted the Actuators return the damper to its original position.
The actuator is overload protected. The actuator can be mounted directly on the damper shaft if square, 12 x 12 mm or 10 x 10 mm (adaptor included); Several mounting brackets are available for applications where the actuator cannot be directly coupled to the damper shaft.
|
|
|
Explosion-proof eletrico servo-control for shutters tagliafuoco, explosion-proof eletrico Servo-control for shutters tagliafuoco, explosion-proof eletrico Servo-control for shutters tagliafuoco, explosion-proof eletrico Servo-control for shutters tagliafuoco, explosion-proof eletrico Servo-control for shutters tagliafuoco, explosion-proof eletrico Servo-control for shutters tagliafuoco, explosion-proof eletrico Servo-control for shutters tagliafuoco
|
|
Actuators for air dampers and smoke extraction dampers, explosion proof
Electrical, explosion proof quarter turn actuators series ExMax and RedMax, for air dampers and smoke extraction dampers, from 5 Nm to 100 Nm, in acc. with ATEX 94/9/EG for installation in hazardous areas zone 1, 2, 21 and 22, for all kind of gas, vapours, mixtures and dust. Actuators with or without fail safe spring return function. 24 to 230 VAC/DC multivoltage supply, 5 motor running times adjustable on site, on-off, 3-pos, 0...10 VDC, 4...20 mA mode, 100 % overload protected, robust aluminium housing with IP 66 protection, optional stainless steel version, integrated heater for use from -40°C to +40°C/+50°C, cable connection, approx. 1 m cable, manual override, squared shaft connection 12x12 mm (size S) and 16x16 mm (size M). series ExMax-... for use in zone 1, 2, 21 and 22. series RedMax-... for use in zone 2 and 22. Optional accessories like external adaptable aux. switches, terminal boxes and mounting brackets available.
|
|
-Explosion Proof linear Actuators with spring return
-Explosion Proof linear Actuators without spring return
-Torque: 800-1000-1600-2000 up to 40000N
-For globe valves
-Power Supply from 24V AC up to 240V AC
-On-Off, 3 Point, Modulating- MFT Multifunction Technology
-Spindle stroke self-adjusting
-Several valve adapter available
-Suitable for zone 1,21
-II 2GD EEx d IIC T6
-IP54
|
|
Explosion-proof linear electric actuator ST 1-Ex
Technical data
Max. load thrust: 8 700 [N]
Switching-off thrust: 10 000 [N]
Operating speed: 8 to 80 [min-1]
Operating stroke: 8 to 80 [mm]
Ambient temperature: -25 to +55 [°C]
Protection enclosure: IP 54
Operating position: any position
Weight: 11 to 15 [kg]
Standard equipment
# Voltage 230 [V] AC
# Terminal board connection
# 2 thrust switches
# 2 position switches
# Space heater
# Space heater's thermal switch
# Local position indicator
# Flange mechanical connection
* substitution pillar version
# Manual control
Additional equipment
# Voltage 24 [V] AC
# 2 additional position switches
# Position transmitter with the following type of signal:
* resistive 1x100 [ohm], 1x2000 [ohm]
* current from R/I converter 4 to 20 [mA] with/without power supply
* current (a capacitive transmitter) 4 to 20 [mA]
# Position controller 0/4 to 20 [mA], 0 to 10 [V]
|
|
Explosion-proof multi-turn actuator MO 5-Ex
Technical data
Max. load torque: 600 [Nm]
Switching-off torque: 250 to 1000 [Nm]
Operating speed: 15 to 100 [min-1]
Number of revolutions: 1 to 150
Ambient temperature: -20 to +55 [°C]
Protection enclosure: IP 55
Operating position: the motor axis should be in horizontal position
Weight: 110 to 130 [kg]
Standard equipment
# 3x400 [V] AC - Terminal board connection
# 2 torque switches
# 2 position switches
# 2 additional position switches
# Space heater with thermal switch
# Flange mechanical connection
# Mechanical position indicator
# Manual control
# switching-off from torque blocking
|
|
Explosion-proof part-turn electric actuator SP 2-Ex
Technical data
Max. load torque: 125 [Nm]
Switching-off torque: 145 [Nm]
Operating time: 5 to 80 [s/90¡Æ]
Operating angle: 60¡Æ to 360¡Æ [¡Æ]
Ambient temperature: -50 to +40 and -25 to +55 [¡ÆC]
Protection enclosure: IP 54
Operating position: any position
Weight: 16 to 16,5 [kg]
Standard equipment
# Voltage 230 [V] AC
# Terminal board connection
# 2 torgue switches
# 2 position switches
# 2 additional position switches
# Space heater
# ¬´hermal switch
# Mechanical stop ends
# Connection with valve flanged ISO 5211
# Manual control
Additional equipment
# Voltage 3x400 [V] AC, 24 [V] AC, 24 [V] DC
# Position transmitter with the following type of signal:
* resistive 1x100 [§Ù], 1x2000 [§Ù], 2x100 [§Ù], 2x2000 [§Ù]
* current from R/I converter 4 to 20 [mA] with/without power supply
* current (a capacitive transmitter) 4 to 20 [mA]
# Position controller 0/4 to 20 [mA], 0 to 10 [V]
# Version with stand
# Version with lever
# Pull-rod
|
|
-Explosion Proof rotary Actuators without spring return with torque from 10Nm up to 4500Nm
-For ball valves
-Power Supply from 24V AC up to 240V AC
-On-Off, 3 Point, Modulating
-Auxiliary switches
-Suitable for zone 1,21,2,22
-II 2GD EEx d IIC T6
-IP66
|
|
Electric ATEX explosion proof Oden P30 actuator for linear or turning control valve applications.
High precision through the Oden Gear System.
Fits most types of valves using ASAB standardised modules and assembly kits
Voltage 24 VDC
Analogue control 4-20 mA
Speed 400 mm/min
Linear Force up to 24 kN
Turning Torque up to 30 Nm (added gear up to 4500 Nm)
|
|
Actuators
Pneumatic and motorized actuators for quarter turn and linear valves (butterfly valves, ball valves, diaphragm valves, gate valves), complete control actuators available, field bus connection and integration into automation systems available
|
|
Valve actuators, explosion proof
Elektrical, explosion proof linear motion actuators series ExRun, RedRun (available III.Q.08) and ExVent (currently available), for valves and other linear motion armatures , from 500 N to 10.000 N, in acc. with ATEX 94/9/EG for installation in hazardous areas zone 1, 2, 21 and 22, for all kind of gas, vapours, mixtures and dust. Actuators with or without fail safe spring return function. 24 to 230 VAC/DC in acc. to type, 5 motor running times adjustable on site, on-off, 3-pos, 0...10 VDC, 4...20 mA mode, 100 % overload protected, robust aluminium housing with IP 66 protection, integrated heater for use from -40°C to +40°C/+50°C, integrated Ex-terminal box, manual override. series ExVent and ExRun-... for use in zone 1, 2, 21 and 22. series RedRun-... for use in zone 2 and 22. Optional accessories like external adaptable aux. switches, terminal boxes and mounting brackets available. Adaptations for all typical linear valves available.
|
|
|
Electric linear actuators, also called thrust drives, are mostly applied to automate globe valves. They are also suitable for the operation of butterfly valves with lever arrangements. AUMA linear actuators consist of the combination of a multi-turn actuator SA and a linear thrust unit LE.
|
|
|
AUMA multi-turn actuators of the type SA operate reliably in various industries worldwide for OPEN-CLOSE as well as modulating service. One of the main applications lies in the automation of gate valves and globe valves. A multitude of further applications are possible in combination with valve gearboxes (worm, bevel and spur gearboxes).
|
|
type MO 3
Max. load torque: 120 [Nm]
Switching-off torque: 150 [Nm]
Operatings speed: 10 to 63 [min-1]
Number of revolutions: 1 to 380
Ambient temperature: -40 to 55 [°C]
Protection enclosure: IP 55 (65)
Operating position: the motor axis should be in horizontal position
Weight: 26,5 to 29,5 [kg]
Standard equipment
¤ Voltage 3x400 V AC
¤ Terminal board connection
¤ 2 torgue switches
¤ 2 position switches
¤ Space heater
¤ Flange mechanical connection
¤ Local position indicator
¤ Manual control
¤ Torque switches blocking in limit position
Additional equipment
¤ Voltage 3x380 V AC
¤ 2 additional position switches
¤ Position transmitter with the following type of signal:
- resistive 1x100 [ohm], 2x100 [ohm]
- current from R/I converter 4-20 [mA] with/without power supply
- current (a capacitive transmitter) 4-20 [mA]
¤ Position controller 0/4 to 20 [mA], 0 to 10 [V]
¤ Electric local control
¤ Mechanical connection with connect adapter
|
|
|
