|
|
| ... products without technical information |
| |
| Static mixers are well established and widespread in all fields of chemical process technology. It is characteristically for static mixers, that, in contrast to dynamic mixers, only the media to be mixed are in motion. The liquids or gases are mixed by pump energy only, while the geometrically strong defined Fluitec mixing elements in the tube remain in position. |
|
For the Verdermix mixers many applications are already so well-known that research does not have to be more than at most a very small part of the quotation phase.
Based on this, we have developed our standard for the manufacture of Verdermix agitators and mixers. Consequently, our customers can benefit from sound and timely advice, based on our vast experience and ample knowlegde of many processes; fully computerised deliveries from stock; modular construction; the use of high quality components and accessories, which are proven to ensure long lifespans under considerably severe circumstances.
Verdermix Static Mixers
Advantages of VERDERMIX static mixers:
- Quick and intensive reaction between the mixable fluids and/or gases
- Easy and simple to install in your piping system.
- Low energy consumption
- No moving parts, negligible maintenance costs and long lifespan
- Low cost |
|
| ... products without technical information |
| |
Many areas applying extractive Gas analysis or dry basis measurement systems such as air emission testing equipment, CEM monitoring and stack test equipment, EPA method test equipment, process gas analysis and others, the sample gas needs to be ‘dried’ before it is fed into the analyser.
The sample drying is achieved by cooling the gas down below dew point. Consequently, any moisture will be condensed and removed from the system.
It depends highly on the gas composition or gas compositions and the ambient conditions, as they may vary significantly in CEM sampling, source testing or for example engine emission test, requires application specific cooling equipment. Thermoelectric chillers have their own strength and weaknesses, so have compressor chillers using a fluidic coolant.
Bühler Technologies is applying both technologies. The coolers are equipped with a cooling block in which heat exchangers are inserted. These heat exchangers are avalible in materials like stainless steel, duran glass or PVDF, with one or two individual gas paths. The temperature of the cooling block is regulated by the Bühler constant control system providing a very stable dew point even under varying ambiend conditiones. The coolers are maintenance free.
The product range includes coolers for hazardous areas (Atex Zone 1 and 2) and water cooled heat exchangers.
For condensate removal either peristaltic pumps or automatic condensate drains are available. Further accessories are available upon request; see respective data sheets for options.
As high energy efficiency is a major concern, modern calculation methods and system design is an inevitable request. |
|
The M&C gas coolers are used in gas analysis to lower the dew point of humid gas to avoid condensation in the analyser(s).
An extremely stable and low gas dew point avoids water vapour cross-sensitivity and volumetric errors.
Water coolers are also available. |
|
Accurate measurement of gases requires gas samples with stable dew points even under harsh ambient conditions. The PKE Models feature a semiconductor Peltier cooling system with an aluminum cooling block. Fitted into the block is a removable high efficient heat exchanger made of stainless steel, DURAN-glass or PVDF.
The PKE 5 is designed for moderate ambient and gas temperatures (150 l/h @ 70°C) and an inlet dew point of about 40 °C (appox. 5 Vol%). For higher ambient temperatures up to a maximum of 50 °C order the PKE 52x.
The dew point of 5 °C is regulated by an electronic controller. The temperature (in °C or °F) of the cooling block is shown on a LED-display. The status is indicated by a flashing display which shows too high or low temperature and operates together with a relay in fail-safe mode.
Condensate is removed by peristaltic pumps, automatic condensate drains or condensate vessels.
Compact design
Easy installation
No maintenance required
Low noise
Efficient heat exchangers made of stainless steel, DURAN-glass or PVDF
Nominal cooling capacity 90/100 kJ/h
Dew point stability 0.1 °C
Status display and -output
Cooling temperature display
Model available for high ambient temperatures |
|
Perfect furnace for delicate gas quenching treatments thanks to the rotative cooling ensuring an excellent cooling uniformity/span>
High cooling speed
Reduction of cycle time thanks to convective heating
Fully automatic process for a perfect reproducibility of the results |
|
Perfect furnace for delicate gas quenching treatments thanks to the rotative cooling ensuring an excellent cooling uniformity/span>
High cooling speed
Reduction of cycle time thanks to convective heating
Fully automatic process for a perfect reproducibility of the results |
|
| ... products without technical information |
| |
standard, DN63-80-100-125
"all stainless steel" DN100-125-150
watertight estate, DS80-125
|
|
| ... products without technical information |
| |
Designed to retract the hose with the assistant of an electrical high-torque motor.
We recommend this reel for truck service shop applications where hose and nozzles can be heavy and overhead cranes have to move. |
|
Car-/Truck-Single systems
Single (double) systems are basicly supplied with the following parts:
- ventilator,
- wall bracket
- motorprotection switch
- exhaust hose (2 hoses)
- exhaust nozzle (2 nozzles)
- exhaust hose support (2 exhaust hose supports)
Description:
Ventilator: 1,000 m3/h, Motor: 0.55 kW · 3 x 400 V · 50 Hz
Car - Single system with exhaust hose, Ø 75 mm, length 5.0 m, exhaust nozzle Ø 75 mm or
exhaust hose, Ø 100 mm, length 5.0 m, exhaust nozzle Ø 100 mm or
exhaust hose, Ø 75 mm, length 7.5 m, exhaust nozzle Ø 75 mm or
exhaust hose, Ø 100 mm, length 7.5 m, exhaust nozzle Ø 100 mm
Ventilator: 2,000 m3/h, Motor: 0.75 kW · 3 x 400 V · 50 Hz
Truck - Single system with exhaust hose, Ø 150 mm, length 5.0 m, exhaust nozzle Ø 150 mm or exhaust hose, Ø 150 mm, length 7.5 m, exhaust nozzle Ø 150 mm
Description
Ventilator: 2,000 m3/h, Motor: 0.75 kW · 3 x 400 V · 50 Hz
Car - Double system with 2 exhaust hoses, Ø 75 mm, length 5.0 m or 7.5 m, 2 exhaust nozzles Ø 75 mm or
2 exhaust hoses, Ø 100 mm, length 5.0 m or 7.5 m, 2 exhaust nozzles Ø 100 mm or
2 exhaust hoses, Ø 150 mm, length 5.0 m or 7.5 m, 2 exhaust nozzles Ø 150 mm
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|
see the results for the following category
