|
|
The Skilmatic range is a self-contained electro-hydraulic valve actuation solution available for both quarter-turn and linear applications. The actuators incorporate sophisticated electronics that provide non-intrusive set-up and interrogation via an infra-red hand held remote. They are suitable for on/off, modulating and emergency shutdown duties in applications up to SIL 3.
•Linear thrust output 1.7 to 5500kN.
•Quarter-turn torque output 65 to 600,000Nm.
•Single-, three-phase or 24Vdc power supply options.
•Non-intrusive infrared setting & configuration.
•LCD display for position, pressure, diagnostics and fault indication.
•Optional bus communications via all major protocols.
•Partial stroke test capability.
•Watertight or explosionproof.
•Double-sealed terminal compartment.
•ATEX, FM, CSA, IEC and GOST certified.
|
|
|
Electro-hydraulic valve actuators for positional, modulating and stepping control of globe, choke, plug, gate, ball, and butterfly valves, for hazardous areas and severe environments, these can be self contained with their own power packs and tank systems or be fitted into an existing hydraulic ring main circuit.
|
|
Motorized hydraulic pump operates continuously,
ensuring positional control with continuous modulation
is available in addition to accumulator storage.
When the system is fully charged, the pump will automatically
unload with a signal from the integral pressure switch
ensuring no excessive heat generation.
|
|
Actuation and control for turbo machinery:
Modern turbo machinery needs to fulfill two basic prerequisites - optimum operation and low impact on the environment. Voith Electronic Drive Systems are active in the field of positioners and control for turbo machinery.
This comprises actuation for gas turbines, steam turbines and compressors, such as for example complete valve assemblies (valve with servo motor), servo motors or pilot controls designed as I/H-converters and way valves for existing positioners and the control system Turcon (turbine control) for steam turbines and compressors.
|
|
Hydraulic actuators
Double acting and single acting hydraulic actuators based on the Petras actuator typical design are available up to 200 barg supply.
Petras can also complete systems with electro hydraulic micro power unit and control systems.
Established in 1966, PETRAS is a pioneer in the design and manufacture of high performance pneumatic and hydraulic actuators for quarter turn valves.
|
|
Good reasons for this automation:
No radial forces have an effect on the shaft of the fitting.
This saves as well as the bearing and the packet
With the hollow shaft design or an adapter hub the required
Eckart rotary actuator can adapted to every Zwick high performance flap
Very fast control times (e.g. 90° in 0.2 seconds) can be realized
By the optimal end cushioning of the Eckart rotary actuator the
closing stop position of the fitting is also saved
The regulation of the volume flows is very simple and repeating exact
No additional lubrication is necessary
|
|
Actuators & Accessories
We provide a complete product line of actuators and accessories to meet all your valve automation requirements.
XOMOX Valves can be readily and inexpensively equipped with a variety of pneumatic, electrical or hydraulic actuators. We also supply a complete line of actuator devices and accessories (e.g. positioners, limit switches, solenoid valves, air filters, etc.) to complement your valving needs.
|
|
| ... products without technical information |
| |
The SIM08 connection box provides an optimal solution for connecting all type of cylinder end-stroke switches, with the following advantages:
Security. Front and rear signals are usually joined in two series. Yet, this solution doesn’t provide any protection to an eventual double signal or connection error and make it difficult the identification of a broken switch. The SIM08 box is equipped with an alarm to any double signal and a led light for each switch permits a fast detection of a non-working switch even if the signal is in series.
Versatility. The box can be fixed directly on the mold. From the box to the press machine there’s a unique connector (IP67 water resistance) with a 5 mt. cable. On the other side of the cable the end user can connect any type of connector - as per his Company standards - with min. 6 pins.
|
|
|
|
