|
|
Size Range ......................... C15 - C75
Torque Output: .................. 10 Nm - 2,600 Nm (81 in-lb -23,800 in-lb)
Air Supply Connection: ... Namur G1/4"
Accessory Top Mount: ... Namur VDI/VDE 3845
Valve Bottom Mount: ...... ISO 5211, DIN 3337
Quality Standards: ........... ISO 9001 certification
Certifications: ................... ATEX 94-9-EC approved to category 2
Health & Safety: ................ Built-in safety features for maintenance and handling
Other Features: ............... Space saving, fast acting, Superior corrosion resistance, Balanced piston forces.
Nested spring sets: ........ 8-12 spring combinations for various operating pressures.
Less air consumption, Less wear, Limit stop for
+/-5° and intermittent stop, Highly visible indicator and puck with flow direction arrows
|
|
The RC range is an extremely compact pneumatic actuator. Its scotch yoke design is particularly suited for valves with high start or end torque requirements. It is available in double-acting and spring-return configurations with torque output up to 4,400Nm (38,700 lbf-in).
The RC200 range is available in a variety of configurations and an extensive range of options and accessories is available.
|
|
IMPACT 2000ª is a high integrity modular pneumatic actuator controlassembly in 316 Stainless Steel. Lighter, stronger and more compact than panel mounting. IMPACT 2000ª offers a significant reduction in total installed cost in both CAPEX and OPEX over panel mounted assemblies.
The modular system does away with comple arrangements using panels, pipes and additional fittings. Using a range of field proven components, valves, spool, poppet or direct acting, and filter regulators are connected in series using a universally compatible interface block and mounted directly onto the valve actuator.
|
|
The external spring positioners are the ideal complement to control, according to a pneumatic or electric control signal, the linear movement of conventional pneumatic cylinders.
The series 120 linear positioner valve is mounted on the base plate, forming a compact assembly of reduced dimensions, directly fittable to the rear cover of any pneumatic cylinder.
The feedback spring, with its mounting accesories, are supplied according to the length of the stroke of each particular cylinder.
1701.PR120: Direct Linear Pneumatic Positioner.
1701.PR120R: Reverse Linear Pneumatic Positioner.
1701.PR121: Direct Linear Electro-Pneumatic Positioner.
1701.PR121R: Reverse Linear Electro-Pneumatic Positioner.
|
|
Heavy Duty Double Acting Ball Valve Systems
Valve sizes from ¼” to 3”
140 in.lbs to 800 in.lbs
Spring Return Valve operators
Single acting with spring close or open
Valve Operator Systems
Spring Return operators are formed by bolting a spring return unit to a double acting Val-U-Act operator. The return movement is effected by a clock-type spring which is pretensioned to about half the operator torque. The amount of pretention is large, compared to the rotation and therefore the torque does not vary more than 20% over the rotation.
Spring returns are factory-installed and adjusted. The spring returns have a worm drive adjustment for setting or changing spring pretension. By inserting a socket key into one end of the worm the spring pretension can be very easily increased or decreased to suit operating conditions. To increase pretension, turn the worm clockwise; to decrease, turn counterclockwise.
|
|
Series 1200 actuators are pneumatic piston operators that are available in spring opposed direct and reverse acting models or a springless double acting configuration.
The series 1200 actuator ranges from 4 to 44 inches in diameter with an available travel of up to 15 inches. The direct and reverse acting models may be fitted with a variety of springs in order to overcome the wide range of forces that may exist on a valve plug.
Viton seals are available for high temperature applications or environments with radiation exposure.
|
|
Georg Fischer manufactures high quality electric and pneumatic actuators for plastic butterfly and ball valves. They are proven in many applications all over the world.
|
|
Series PMD/PMS
For use with Ball Valves up to 2"
Series PAD/PAS
For use with Ball Valves up to 2"
Series PKD/PKS
For use with all sizes of Ball Valves and with Butterfly Valves up to 8"
Series PCD/PCS
For use with all sizes and types of Ball Valves and Butterfly Valves
|
|
Due to its modular and adaptable design, that combines linear cylinder, ON/Off and modulating accesories, mounting accesories and the integration according to custoemrs specifications, specific linear actuation solutions cab be supplied for linear valves actuation: Globe valves, Gate valves, Knife-gates valves and Diaphgram valves.
Main characteristics:
Thrust range from 500 N to 120.000 N.
Strokes available up to 2000 mm.
On/Off and Modulating service.
Single or Double Acting.
Mounting accesories according to ISO.
Different ATEX certifications for EXplosives ATmospheres.
Handwheel for manual operation optional.
Wide range of switching and signalling options.
|
|
Single acting actuors PETRAS
Single acting pneumatic actuators up to 4 500 Nm at 5 barg supply pressure.
rotation : 90° - 120° -180° - 240°
Materials
- high grade aluminium
- cast iron
- carbon steel
- stainless steel
Hydraulic version available up to 200 barg supply pressure
Established in 1966, PETRAS is a pioneer in the design and manufacture of high performance pneumatic and hydraulic actuators for quarter turn valves.
|
|
G Series:
A unique Scotch Yoke design incorporating a 5 degree off set in the scotch yoke mechanism which enables the maximum torque to be delivered at the closed position. This is ideal for butterfly valves, where the maximum torque is required at the seat break in and break out positions. The G series actuator range meets the latest Atex requirements and is produced in an ISO 9001: 2000 factory. Full traceability is available with each actuator, and a wide range of options are available. The standard G Series range has 15 Double acting and 15 Spring return Models and covers the Tomoe Valve range from DN40 - DN600.
Other models:
To fully complement the characteristics of the Tomoe butterfly valve design, a full range of Rack Pinion and Vane type actuators are available. All are sized to match the low torque benefits offered by the Tomoe seat design.
|
|
|
rack and pinion actuators with 24 double-acting and spring-return models with torque outputs from 80 to 40,000 lb-in. Actuators comply with NAMUR, DIN 3337 and ISO5211 standards. Models available for 180 degree extended rotation and with accessories, including limit switches and manual overrides.
|
|
VPVL-SS High-Performance Actuators
VALV-POWR® Series VPVL-SS double-opposed piston actuator is the Jamesbury brand of forged stainless steel actuators designed specifically for corrosive environments. Available in double acting and spring return versions, these actuators are ideally suited for a wide range of process applications.
|
|
|
The Morin Partial Stroke Test Device (PSTD) was developed to allow users to test emergency shut-down valves without disrupting the process. The PSTD unit is locked out when the unit is in service and the valve functions normally. When the unit needs to be tested, the operator unlocks the device and inserts the stop pin, allowing for 15 degrees of valve travel to sufficiently test the valve package. Unlike electronic versions, you are guaranteed a hard stop and no over-travel, time after time, without any special calibration.
|
|
Valve actuator that moves according to the amount of air pressure applied to a diaphragm.
Comprehensive selection of pneumatic actuators to meet every application.
|
|
What makes SOMAS actuators so special? One reason is that they have been specially designed to cope with the requirements of the process industry for reliable operation and precise control. Our actuators are mainly intended for use with SOMAS valves , but they can be easily adapted for use with other valves demanding a 90 degree arc of operation.
We have spared no effort in order to eliminate any backlash between the moving parts of the actuator or between the actuator and the valve. This has created the neccessary prerequisites for pinpoint precision and has laid the foundation for accurate diagnostics.
|
|
Petras offers a range of 3 positions pneumatic actuators up to 240° rotation available in double acting and single acting version.
System P03 range : 3 postions actuators with adjustable intermediate position :
- 3 positions 90° double and single acting for dosing applications
- 3 positions 180° or 240° for 3 ways valves
Established in 1966, PETRAS is a pioneer in the design and manufacture of high performance pneumatic and hydraulic actuators for quarter turn valves.
|
|
ACTUATOR DOUBLES EFFECT (Abbreviation OF):
Actuators 1/4 turn KINETROL are distinguished from the other jacks by the technology of the axis-pallet:
- 1 only part moving: direct, precise movement and without play. Robust and fast apparatus
- Sealing pallets by lip seals: great lifespan (several million cycles return ticket)
- Modular Assembly of the options
ACTUATOR SIMPLE EFFECT (Abbreviation SE):
Constituted of 1 actuator doubles standard effect to which is added a return spring (modular assembly) assembled between the actuator and the element to be motorized for a return for lack of air.
- Cumbersome Spring spiral not very
- Spring placed in a case seals (sheltered driving air and ambient air thus protected from any risk of corrosion)
- Great lifespan without any maintenance.
|
|
Available in double-acting and spring-return configurations The RC range is an extremely compact pneumatic actuator. Its scotch yoke design is particularly suited for valves with high start or end torque requirements. With torque output up to 4,400Nm (38,700 lbf-in)
The RC200 range is available in a variety of configurations and an extensive range of options and accessories is available.
|
|
Double acting actuors PETRAS
Double acting pneumatic actuators up to 10 000 Nm at 5 barg supply pressure.
rotation : 90° - 120° -180° - 240°
Materials
- high grade aluminium
- cast iron
- carbon steel
- stainless steel
Hydraulic version available up to 200 barg supply pressure
Established in 1966, PETRAS is a pioneer in the design and manufacture of high performance pneumatic and hydraulic actuators for quarter turn valves.
|
|
Description:
The RPDA Rotary Piston Double Acting Actuator is designed for heavy duty control applications that require optimum performance. The RPDA is typically utilized when applications require a "lock last" failure mode. The RPDA incorporates a “crank-arm” mechanism specifically designed for the rigors of throttling control valve applications. The RPDA can accept high pressure power supply gas up to 500 psig (3447 kPa) enabling the use of smaller actuators or Becker’s exclusive Bleed to Pressure System (BPS) feature.
|
|
Description:
The RPSR Rotary Piston Spring Return Actuator is designed for heavy duty control applications the require optimum performance. The RPSR is typically utilized when applications require the control valve to “fail open” or “fail closed” upon loss of power supply gas. The RPSR incorporates a “crank-arm” mechanism specifically designed for the rigors of throttling control valve applications. The RPSR can accept high pressure power supply gas up to 500 psig (3447 kPa) enabling the use of smaller actuators or Becker’s exclusive Bleed to Pressure System (BPS) feature.
|
|
TORK T-RPA ..SR Single acting pneumatic rotary actuator ,90 degree turn rack and pinion type pneumatic rotary actuator . it is recommend 6 bar supply pressed air and out put torque value from 12Nm.upto 1150Nm
applications :ball valves,butterfly valve,plug valves,dampers
TORK pneumatic actuators work on-off with namur solenoid valves and proportional rotary positioners
|
|
| ... products without technical information |
| |
|
EExPress™ is a new concept of 5/2 valve manifold to control pneumatic actuators in dangerous environments like chemical, petrochemical applications. The concept consists in an patented "integrated protection", a unique feature on the market today, which permits to install the manifold directly close to the actuators without being mounted in expensive explosion-proof pressurised cabinets.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|
see the results for the following category : 
