|
|
7011-5 - Hydraulic Power Clamp
The power clamps (double action) are used where a high clamping force is needed combined with small clamp dimensions. The cylinder body can be turned 90� in relation to the clamp.
1. max. clamping force 1250 daN (2810 ib)
2. max. operating pressure 250 bar (3625 psi)
00863DE/100986DE - Hydraulic Edge Clamp
StrongHold edge clamps perform three functions: locating the workpiece, clamping horizontally against secondary locators, and clamping vertically against the primary locating surface.
1. Conventional or manifold mount versions
2. 15 degree clamping angle
3. Single acting
4. 2000 lbs. clamping force
|
|
REMARK
1 : The mounting surface finish should be no rougher than Rz 6.3 (ISO 4287:1997).
2 : Be sure to use O-ring included at all times.
3 : Tightening torque for mounting should be as per the above table.
4 : The hardness at the top portion of round top type plunger is HRC54.
|
|
* Maximum operating pressure 500 bar
* Short delivery times - Large stock range
* Piston diameters from Ø25 mm to Ø40 mm
* Rotates to left or right with 45, 60 or 90° angle of rotation
* Integrated in a tool without lining
|
|
|
|
|
|
030 - SELECT Hydraulic Swing/Pull Clamp
SELECT hydraulic threaded body swing clamps are high quality and cost effective alternatives to competetive brands.
- Range of sizes
- available in sigle or double acting versions
- field adjustable swing direction
- MRO interchange
035-1 - SELECT Pneumatic Swing/Pull Clamps
SELECT line of pneumatic swing/pull clamps are designed for applications not requiring hydraulic power. The fast acting clamps can generate up to 50 pounds of clamping force from shop air.
- Swing motion available in 0, 45, 60, and 90 degrees
- Four styles of arms
- Double-locked arm design is bolted to piston shaft and around shaft diameter for extra rigidity
- Double-acting design
727D - Hydraulic Swivel Clamping Cylinder
Hydraulic swivel clamping cylinders are particularly designed for applications which require high clamping forces and easy loading of workpieces in confined spaces.
- swivel left
- max. clamping force 475, 850, 1250 daN
- max. operation pressure 250 bar (3625 psi)
|
|
|
Model TME is a retractable lever type clamp and ensures sufficient mold holding force by a heavy duty spring even at the oil pressure failure.
|
|
ThePitbull® Clamp is a revolutionary new fixture clamp with positive down force and a low gripping profile. High vertical and horizontal clamping forces are generated., considering the size of the Pitbull® Clamps. It uses a standard cap screw and available in 5 sizes and several styles, a tool steel knife edge for aggressive stock removal, a tool steel blunt edge for general purpose and a brass version to help prevent marring the workpiece.
Unique feature of PITBULL® CLAMPS
- Extremely low bite
- Positive down force
- High resistance to rip-out
- Simple, sturdy, high quality design and components
- Gain maximum tool access to your work
- Virtually eliminate lost work
|
|
The clamping elements react in the shortest possible response time by the patented pneumatic pre-loading of the system of the spring plates in the diaphragm.
These safety systems are permanently operational for the maximum machine protection.
|
|
REMARK
1 : Mounting surface finish should be no rougher than Rz 6.3 (ISO 4287 :1997). 2 : Be sure to use O-ring included at all times.
3 : Tightening torque of body thread should be as per the table below.
4 : When mounting an attachment, be sure to hold the wrench width at the tip by spanner, etc.to prevent the piston from rotating before
tightening the bolt. Do not attempt to tighten it with a hydraulic-powered resistance against rotation
|
|
The original MITEE-BITE T-Slot Clamp combines our unique cam action clamping element with a T-nut.
-Locks in machine T-slot for low profile clamping.
-Makes fast set-ups possible right on the machine table.
-Brass hex follows contour of unusual shaped parts.
-Packaged in pairs or complete kits.
|
|
These special constructions are a proved solution for the isolated blockage of high horizontal dynamic forces.
E. g. for friction screw presses, horizontal press machines, longitudinal alignment of long machine beds and their fixation etc.
|
|
|
|
|
|
Hardinge Collet Blocks grip round, hex, square or odd-shaped parts and can be used horizontally or vertically on mill tables, flat or angled fixture plates, tombstones or rotary trunnions. Sizes are available from the 1C micro medical machining industry up to the 35J mid-range automotive and aerospace industries. Modular collets blocks are compact with a low profile for increased axis travel and for maximum layout of the workspace. A collet can provide certain advantages over a jaw chuck, vise and other clamping methods.
There are some advantages of using Collet Blocks instead of a standard vise or 3-jaw chuck. A collet automatically centers the workpiece for reduced setup time. Centers remain fixed when the fixture is removed from the machine table. A collet provides equal gripping pressure around the circumference of the part unlike a standard vise or a 3-point contact jaw chuck. Thin-wall parts or delicate materials may crush or distort in a standard vise or jaw chuck. Collets ordered with serrations can add additional gripping power to prevent push-back and radial slipping. Extended-nose collets can provide additional tool clearance. Some collet blocks accept expanding collets to grip a part at the internal diameter. Collet blocks are modular for arranging on a pallet for multiple part processing and quick pallet changeover.
Collet blocks and rotary trunnions can be ordered online at www.shophardinge.com.
|
|
| ... products without technical information |
| |
 see the results for the following category : Hose clamps |
|
|
