|
|
A1 5C Collet index fixture.
Universal indexer with 24 space ring, 5C Collet taper in spindle nose.
Takes 4" chuck, 3 jaw, (not included) #1034 chuck.
Head can be angled from 0 deg. to 100+ deg.
Indexes quickly and easily, spindle locks in positive position.
Can be dismantled in seconds for easy cleaning. Changing index rings gives numerous combinations of divisions.
Spindle locks with index pin and/or horseshoe rings at rear of spindle.
For drill presses, milling machines, grinders and layout work.
22 lbs. Made in USA !!!
Model: A1
Options: AT tailstock. # AT
3 jaw chuck, # 1034
Blank index ring # AR-O
20 space index ring # AR20
36 space index ring # AR36
Other products available:
|
|
simple manual operation
1.00 and 2.00 inch capacity
Fixed collet position
horizontal or vertical mounting
2 to 32 index positions (1.00 Fixture)
2 to 32 index positions (2.00 Fixture)
coollant Flush
Accuracy to within .001 of true position
Easy part loading
Steel and Cast Iron construction
|
|
|
|
|
|
Bluid-in Zeropoint Quickclamping cylinder K5, round
Screw-in version
Hydraulic release (or pneumatic)
Cover and piston hardened
Repeat accuracy < 0,005 mm
Assembling diameter Ø 39 mm
Pull in force 5 kN (hydraulic)
Pull in force 1,5 kN (pneumatic)
Holding force 13 kN
Use:
With a small footprint for installation in base plates, machine tables, clamping profiles, columns and towers, swivel bridges, machine pallets and clamping pallets. Also suitable for use as „cylinder locks“ with high repeatability.
Note:
Installation Zeropoint Quickclamping cylinder with a low installation height of 19.8 mm and an installation diameter of 45 mm (M45 x 1). Hydraulic pressure is only needed for unclamping (min. 40 bar / max. 50 bar). The installation Zeropoint Quickclamping cylinder is mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage. The contact surface is the upper surface of the housing.
On request:
- Installation diagrams on request
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
|
|
Bluid-up Zeropoint Quickclamping cylinder K5, round
Hydraulic release (or pneumatic)
Cover and piston hardened
Repeat accuracy < 0,005 mm
Global diameter Ø 62 mm
Pull in force 5 kN (hydraulic)
Pull in force 1,5 kN (pneumatic)
Holding force 13 kN
Use:
For mounting on machine tables, clamping profiles, columns and towers, measuring machines, assembly stations.
Note:
Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The Zeropoint Quickclamping cylinders are mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage. The contact surface is the upper surface of the housing.
On request:
- Individual housing can be supplied on request
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
|
|
PClamp clamps and brakes rod loads safely amd quickly. It can be adapted to standard systems such as pneumatic cylinders from leading manufactures (e.g. SMC, Festo= or to individual solutions. Rotatory clamping can also be achieved with PClamp. Certified systems from Employer's Liability Insurance Association can be realised.
Area of application:
Linear rails and guide ways
Clamping of linear axis
Swivel tables
Rotary tables
Spindles, feeders
Rod, piston, spindle clamping
Elevating devices
Hydraulic presses
Hydraulic lifts and elevating tables
Safety catches
Blocking systems
High-lifting devices
|
|
|
Safety Locks similar to Safety Catchers and Safety Brakes are used against failure of lifting members. But in contrast to those they are not suitable to decelerate masses or to dissipate kinetic energy. On the other hand, the rod displacement to build up the holding force is very small, so that this units can be used for a approximitive positioning tasks as well. Furthermore this design principle allows compact solutions even for small rod sizes (smaller than for Safety Catchers). In the field of pneumatic clamping devices the Safety Locks are providing the absolutely highest holding forces in relation to housing dimensions.
|
|
Active without pressure – incredible holding force
The pneumatic Clamping and Braking Element for piston rods RB.
The RB series is based on our proven wedge slide gear principle and is used for clamping and braking without pressure.
This element was developed for deployment on round-shaft guides or piston rods with a surface hardness of min. HCR 54.
The compact design is suitable for shaft diameters of Ø10 to Ø60 and allows holding forces of up to 60,000 N at a pneumatic opening pressure of just 4 bar.
As a specific feature no reset is needed for restarting.
The RB series stands out for its short reaction times. Even in vertical deployment, short braking distance are achieved in less than 30 ms
|
|
OK-VISE rotary columns are made of aluminium and they come with steel made corner clamps. They work as a trunion unit between indexer and a tail support. This new system makes efficient use of machinable area a reality, ultimately leading to savings in tool changes, less operator interventions and extended cycle times. Most important feature is a possibility to use subplates resulting to a remarkable cut down in machine stop times which is critical especially in the vertical machining centers.
Parts fixturing probably represents the best value in today´s metalworking technology, if you calculate the cost of a CNC machine tool, the cutting tools, tool-holders and tool-changer with both the programming and the design software and compare these investments to the cost of your workholding equipment. Fixturing normally costs only a fraction of the amount the others cost. Yet, the potential for time savings and process improvements offered by a good fixturing solution are substantial.
|
|
|
|
|
|
Bluid-in Zeropoint Quickclamping cylinder K10, K20, K40, round
Hydraulic release
Cover and piston hardened
Repeat accuracy < 0,005 mm
Assembling diameter: K10: Ø50mm, K20: Ø78mm K40: Ø102mm
Max. pull in force 40 kN (hydraulic)
Max. pull in force 30 kN (pneumatic)
Max. holding force 105 kN
Use:
With a small foot-print for installation in base plates, machine tables, clamping profiles, columns and towers, swivel bridges, machine pallets and clamping pallets.
Note:
The installation Zeropoint Quickclamping cylinders have high holding and pull-in forces with very small installation dimensions. Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The Zeropoint Quickclamping cylinders are mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage.
On request:
- Installation diagrams on request
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
- Also available as an individual flange version
|
|
Bluid-up Zeropoint Quickclamping cylinder K10, K20, K40, round
Hydraulic release (or pneumatic)
Cover and piston hardened
Repeat accuracy < 0,005 mm
Global diameter: K10: Ø78mm, K20: Ø112mm K40: Ø148mm
Max. pull in force 40 kN (hydraulic)
Max. pull in force30 kN (pneumatic)
Max. holding force 105 kN
Use:
For mounting on machine tables, clamping profiles, columns and towers, measuring machines, assembly stations in connection with clamping flange no. 6370ZB.
Note:
Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The modules are mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage. The hydraulic version has 1 connection for clamping / unclamping (G1/4 or G1/8).
On request:
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
- Can also be supplied with centering pins for quicker and more precise installation
|
|
|
|
|
|
Bluid-in Zeropoint Quickclamping cylinder K10, K20, K40, square
Hydraulic release
Cover and piston hardened
Repeat accuracy < 0,005 mm
Assembling diameter: K10: Ø50mm, K20: Ø78mm K40: Ø102mm
Max. pull in force 40 kN (hydraulic)
Max. pull in force 30 kN (pneumatic)
Max. holding force 105 kN
Use:
Can be used as a single clamping point or combined with round installation Zeropoint Quickclamping cylinders in base plates, machine tables, clamping profiles, columns and towers, swivel bridges, machine pallets and clamping pallets. A square Zeropoint Quickclamping cylinder prevents the pallet from twisting. The indexing function enables positioning every 90°. Specially suitable for use in turning.
Note:
The installation Zeropoint Quickclamping cylinders have high holding and pull-in forces with very small installation dimensions. Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The Zeropoint Quickclamping cylinders are mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage. Square pallet for screwing onto the pallet see item no. 6370ZA.
On request:
- Installation diagrams on request
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
|
|
|
|
|
|
Bluid-up Zeropoint Quickclamping cylinder K10, K20, K40, square
Hydraulic release (or pneumatic)
Cover and piston hardened
Repeat accuracy < 0,005 mm
Size: 85x85mm, 120x120mm, 150x150 mm
Pull in force 40 kN (hydraulic)
Pull in force 30 kN (pneumatic)
Holding force 105 kN
Use:
Can be used as a single clamping point or combined with round surface-mounted Zeropoint Quickclamping cylinders in machine tables, clamping profiles, columns and towers, measuring machines, assembly stations in connection with clamping flanges no. 6370ZB). Clamping flange size 20 for K10, size 40 for K20, for K40 integrated onto the housing.
Note:
Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The Zeropoint Quickclamping cylinders are mechanically locked in the clamped position. The ad-vantages of this are that there are no cumbersome lines and no danger of leakage. The hydraulic version has 1 connection for clamping / unclamping (G1/4 or G1/8). Square pallet for screwing onto the pallet see item no. 6370ZS.
On request:
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
- Can also be supplied with centering pins for quicker and more precise installation
|
|
The clamp arm rotates 90° as it extends away from the work piece providing clearance and access for unload/ load operations. Double acting operation and standard magnetic piston offer positive cycles, durability and work piece detection features. Extruded aluminum body mounts directly and rigidly to equipment surfaces in a minimum of space.
Operation cycle:
1) Clamp arm extends (straight line) as it releases work piece from clamp loads.
2) Arm rotates 90° to full extend position.
3) When retracting, clamp arm swings 90°.
Model Code R = clockwise rotation, Model Code L = counterclockwise rotation.
4) With clamp arm in position over the work piece, it follows a straight line path to apply clamping force.
|
|
HORIZONTAL-HANDLE TOGGLE CLAMPS
VERTICAL-HANDLE TOGGLE CLAMPS
PUSH/PULL TOGGLE CLAMPS
Toggle Edge Clamps
LATCH-ACTION TOGGLE CLAMPS
TOGGLE PLIERS
AIR-POWERED CLAMPS
|
|
|
|
|
|
|
The grasshoppers EMILE MAURIN: New ergonomic handle Bi-matter!! A very broad range steel and stainless! The new grasshoppers EMILE MAURIN are provided with an ergonomic handle Bi-matter for a better comfort of use. The non-skid flexible part is in contact with the hand and the harder part in contact with the grasshopper. These grasshoppers have also 2 other technical advantages: an articulation made safe with an integrated thrust and an arm out of U slightly widened to avoid the loss of the screw of plating. The range of grasshoppers EMILE MAURIN is composed of: thorough grasshoppers: with horizontal base plate, vertical or side; with full arm; reinforced; with handle of safety, anti-reflecting drawn grasshoppers: with horizontal base plate, vertical or side; with full arm; with handle of safety, anti-reflecting grasshoppers with sliding tube grasshoppers with hook pneumatic grasshoppers And of course of many models are proposed out of stainless for specific uses in industries such as chemistry and agro-alimentary.
|
|
Material:
Steel or stainless steel
Surface finish:
Galvanized and chromated,
clamping spindle and nuts phosphated,
stainless steel natural finish,
plastic handle oil-resistant
|
|
Vertical
Hold Down Vertical 1000lbs max
This heavy duty clamp is available with solid bar and U-Bar construction. It accepts all 1/2-13 diameter spindles. The solid bar model is supplied with a 70901 bolt retainer. The U-Bar model is supplied with 70902 flanged washers. Spindle assembly 70903 must be ordered separately for both models.
Holding capacity: 1000 lbs. max.
Weight: 2 lbs., 7 oz.
Handle moves 67°, bar 120°
Solid Bar: 7/8" height, 3/8" wide
U-Bar: 7/8" height, 17/32" wide
Horizontal spindle adjustment: 3 1/8"
Spindle Thread: 1/2-13
Horizontal
Hold Down Horizontal 750lbs max
This horizontal clamp is available with U-Bar construction in a flanged or straight base. Supplied with a 70915 neoprene tipped spindle assembly. Both models supplied with a blue vinyl handle.
Holding capacity: 750 lbs. max.
Weight: 1 lb., 8 oz.
Handle moves 55°, bar 90°
U-Bar: 3/4" height, 7/16" wide
Horizontal spindle adjustment: 2 1/4"
Spindle Thread: 3/8-16
|
|
|
WDS stock a huge range of Toggle Clamps in both Mild and Stainless Steel. Vertical, Horizontal and High Speed options are catered for in the range that is covered within the Standard Parts catalogue. For further details or a copy of any of the catalogues available from WDS visit our web site or call + 44 (0)113 290 9852.
|
|
Advantages
- Pneumatic clamping with high forces
- Safety clamping RotoClamp Standard - if the air supply fails then systems claps
- The values of hydraulic clamping are reached and exceeded
- Low system costs in comparison to hydraulics
- Simple installation
- Compact design
- Suitable for all shaft sizes
|
|
Bolts
Leveling Mounts
Screws
Micro Clamps
Studs
Nuts
Washers
|
|
|
To reach a maximum on production output on your machine tool, we offer you a wide range of standard elements, or we design and manufacture your specific Cube or Monoblock according to your specifications and requirements, withhin an overall accuracy of <0.01 mm.
|
|
|
Our quick change palletizing system offers you the perfect interface between your machine tools and work holding system or work pice. Beacuse of its high efficency, it increases your production output, and reduces your setup times up to 90%.
|
|
Zeropoint Quickclamping compact cylinder
Hydraulic release
Cover and piston hardened
Repeat accuracy < 0,005 mm
Size: K10, K20
Use:
For retrofitting to modular profiles, columns, tombstones and cubes. Can be used with thin wall sections..
Note:
There are 5 standard connection options. 4 connections are installed laterally on the outside surface at a 90° angle. Connection is also possible in the base of the Zeropoint Quickclamping compact cylinder.
On request:
- Installation diagrams on request
- Automation solutions such as blowing out, blowing off, isolated applications, sealing air and media ducts
- Individual solutions, such as nipple and installation compatible or installation compatible for existing systems
|
|
Zeropoint Quickclamping cylinders with pusher and central locking against pollution for automatised solutions
Hydraulic release
Cover and piston hardened
Repeat accuracy < 0,005 mm
Assembling diameter Ø 78 mm
Pull in force 20 kN
Holding force 55 kN
Use:
For installation in base plates, machine tables, clamping profiles, columns and towers, machine pallets and clamping pallets.
Note:
Through the central locking the pollution particles can not go into the nipple bore. The central locking element advances with an individually defined spring force
Blowing out and sputter functions
On request:
- Installation diagrams on request
- Hydraulic move-out of central locking
|
|
|
|
|
|
Zeropoint Quickclamping cylinder with release and contact controls for automatised solutions
3 possibilities of monitoring:
- Pneumatic monitoring:
Function of blowing out by compressed air for the cleanliness of support surfaces. After the installation of the pallet of workpieces, it occurs in the pressure line a dynamic pressure, of which this one could be detected by the mean of a pressure sensor.
- Electric monitoring:
Direct position monitoring of the clamping piston in the Zeropoint Quickclamping cylinder by the mean of an inductive sensor. Electric signal when the Zeropoint Quickclamping cylinder is clamped. Small height necessary for the assembling like for the Zeropoint Quickclamping cylinders K5 (19,8 mm) and K40 (42 mm).
- Hydraulic monitoring:
Monitoring of the clamping piston by a hydraulic closure valve. Dynamic pressure when the Zeropoint Quickclamping cylinder is opened, which can be detected by mean of a pressure sensor. Free hydr. flow when the Zeropoint Quickclamping cylinder is closed. Despite a hydraulic sensor, only small height for assembling is necessary.
|
|
Size: K20 ITH6
Zeropoint Quickclamping cylinders with turbine for automatised solutions with:
• Turbine function for complete cleaning of support surfaces without „shady side“
• Central locking against pollution particles
• Hydraulic or pneumatic locking sensors
• Control of contact by air blocked
• Hydraulic pre-expulsion for palletizing solutions with also possibility to swing completely free during the catchment
• No damage of media-coupling
|
|
Zeropoint Quickclamping extrusion cylinder for applications by:
• Round tables and 5 axes milling machines, turning machines
• Better level holding
• Large support surface
• Free passage for flange piece, tubes, forks ...
|
|
Clamping systems for measure machines as building set
The component fixing is especially critical in the measure technique. You must guarantee that the component is fixed on a measure machine without any bracing. Otherwise the measure results would be adulterated and this may have serious consequences.
The flexibility of the clamping systems is also very important. A remodelling must be fast and uncomplicated. This is an ideal territory for the clamping system “Spannfix” from THOME PRÄZISION.
A wide modular system affords the fast prepare and accommodate of devices. All parts are produced with high-class and hard anodised aluminium. In addition to a saving of time can be reached a saving of costs because of measure results and flexibility of the system.
Flexible, tough and easy. Our clamping system also solves your clamp jobs fast and faithful.
|
|
SPEEDY classic - mechanically / hydraulically
- Our most complete and versatile system
- available in 4 sizes with draw in forces from 5.3 to 30 kN
- Draw in- positioning - clamping - releasing- retraction, all these functions are integrated in a single element
- best suited for full automatic solutions
- decades have proven the wide range of applicability of this zero point mounting system
|
|
SERIES-9 CLAMPS
This adjustable low profile, cam action clamp provides clamping of different size work pieces merely by rotating the clamp to one of its other edges.
The clamps are 10mm high and use an M12 cam screw. Each of the six clamping surfaces is a different distance from the centerline by 1mm as shown in the chart. Therefore, one Series-9 clamp can hold parts that vary up to 9.4 mm simpy by rotating the clamp to a different clamping surface.
- Serrated or smooth edges
- Heat treated and plated
- 17800 (N.m.) holding force
|
|
 see the results for the following category : Hose clamps |
|
|
