|
|
Two types of capacitor can be differentiated for mains applications. X capacitors, where a breakdown of the capacitor due to lightning or switching transients would not lead to an electric shock hazard and Y capacitors, used in applications where capacitor breakdown could cause a dangerous situation.
EMC Partner capacitor test systems are used to simulate transient (impulse) and active flammability tests on both X and Y capacitor types over a wide range of values.
MIG0603CAP provides impulses up to 6kV, MIG1212CAP generates 12kV higher energy impulses and MIG1803CAP is used for active flammability testing.
Capacitor testing is performed on batches of 24 samples with all values being recorded. Capacitor test systems from EMC Partner can easily be extended to include automatic switching between samples and registration of test values.
|
|
High Voltage Test Devices
Whether as a stand alone system, or part of a fully automated test system – the Elabo High Voltage Test Device sets itself apart with its wide range of applications and versatility. All test systems come ready and equipped to handle most jobs, though they can be adjusted with the appropriate plug-ins to meet further requirements. In addition to automated use, which is controlled only through an interface, there are also models with integrated touch screens available. PC-Software packages are available to assist in the assembly of complex systems, which cover all the requirements of a modern testing facility (Test Plan Creation, Visualization, Documentation, Statistics, etc.).
|
|
|
|
|
|
PART # SBS-IBEX
BATTERY DIAGNOSTIC TESTER
The new SBS-IBEX is a cutting edge digital battery diagnostic tester meeting all IEEE Standard Recommendations for all stationary applications such as telecommunication's back up power, utility switching power, uninterruptible power systems (UPS) and more. The new IBEX can measure the accurate internal resistance (R), voltage (V), temperature (ºC) with the world's first ripple-removing algorithm (KR PAT No. 0494489) within a short time (3 seconds or less) during flotation charge. The new IBEX has been in use worldwide with the utmost in satisfaction and reliability by end users.
The SBS-IBEX comes complete with Exmons Battery Management Software that allows the user to trend battery measurement data, export data to excel and/or create a full report with the click of a button. Note: Trended battery measurement data can detect impeding battery failures before a power backup is affected and with enough advance notice to replace the failing batteries.
ADDITONAL PARTS:
SBS-IBEX 4-PIN SET
SBS-IBEX ARM ROD
SBS-IBEX 4-POINT PIN PROBE
SBS-IBEX 2-POINT PIN PROBE
SBS-IBEX CLIP PROBE
SBS-IBEX DC CLAMP
SBS-IBEX POLY BAG
SBS-IBEX LI-ON BATTERY
SBS-IBEX SHUNT
SBS-IBEX CHARGER
SBS-IBEX CASE
|
|
SGDA impulse test systems can be used to generate impulse voltages simulating lightning strokes and switching surges.
The stage energy is 5 or 10 kJ. Max. charging voltage is 3MV.
Applications covered include testing according to IEC, ANSI/IEEE as well as other national standards. The basic system can be upgraded in various ways for special tests and for greater ease of operation. A number of additional circuits and components allow optimising the impulse test system for tests on different kind of high voltage test objects.
The generator is due to its unique, modular, patented structure (the D-shaped generator body also forms the enclorsure for the sphere gaps) perfectly suited for transportation and easy on-site erection. Also the internal inductance is the lowest ever built
|
|
For testing the insulating strenght of transformers, motors, electric
machines and electrical plants and equipment.
|
|
The most frequent cause of damage in industrial electronic systems is overvoltages, caused either by switching actions in the equipment itself or by atmospheric discharges such as lightning. Low transfer impedance characterizes a current impulse and high transfer impedance results in a voltage impulse. To simulate both conditions, a Combination Wave Generator (CWG) delivers a voltage impulse into an open circuit and a current impulse into a short circuit. This is also known as a “Hybrid” generator.
Power network transients can be modified by the cable properties so that in a well protected domestic or commercial environment, the impulse energy adopts an oscillatory form at 100kHz. This is the “Ringwave”.
Surge testing is performed on power or communication networks, which require Coupling and Decoupling Networks (CDNs) to superimpose the impulses and provide protection for auxiliary equipment.
EMC PARTNER manufacture a range of surge generators up to 100kA and 100kV.
|
|
# B+K Precision Battery Capacity Analyzers tests Lead Acid Batteries and displays the batteries stored charge capacity as a percentage and displays both the loaded and un-loaded battery voltage. Models 601 and 602 can also display the battery under test’s internal resistance. These units identify batteries, which may be defective or deteriorated. They are perfect tools for testing battery back up systems for emergency lighting, alarm, sprinkler systems, UPS devices and any system using lead acid batteries to provide power. Works with 6V and 12V lead acid batteries
# Settable Ah from 1 to 100 in 1Ah steps (works best on batteries from 5 to 99Ah)
# Powered by the battery being tested
|
|
Testboy Profi LCD Plus
Two pole voltage tester with LC-Display
Display DC and AC voltage from 6V to 1000V Automatic measuring range selection.Single pole phase testing > 100V AC,Two pole phase sequence indication (R and L) Resistance testing up to 2000 Ohm Continuity testing up to 150 Ohm (acoustically) RCD – testing lever two button LED torch lamp
Easy operable click system to change the socket dimension from Schuko to CEE -Socket Special test tips applicable also for WAGO clamps Removable 4mm test tips adaptor Backlight lever sensor IP 65, dustproof and waterproof CAT IV 1000V IEC/EN 61243-3 (DIN VDE 0682-401) TÜV/GS tested and approved
5 years manufacturer’s warranty
|
|
The KD1E/15D is a digital HV potential indicator which can be used to indicate the presence of voltage or make voltage measurements on earthed neutral systems up to 15kV.
The potential indicator displat is powered by an integral rechargeable battery and is supplied complete with battery charger and PH3 proving unit in a bespoke carrying case
|
|
Instantaneous check on battery deterioration. Model 3555 for compact storage batteries: portable telephones and similar applications
Model 3555: support for high-capacity batteries
Model 3555: for compact storage batteries (portable telephones)
The increasing importance of battery testing
Three-rank rating of battery state: Pass, Warning, or Fail
|
|
Digital, highly advanced, multi-purpose and smart Partial Discharge and Diagnostics System for on-line and off-line PD testing on power apparatus and high voltage insulation systems, for both in-house and on-site applications.
according to the standard IEC 60270, VDE 0434, ANSI as well as various IEEE standards
PD quality tests on high voltage equipment
PD diagnosis on developing insulating materials
Designed for on-site PD diagnosis tests as well as for manufacturing and research
PD fault location for power cables
|
|
| ... products without technical information |
| |
Primary pressure standard: Deadweight Tester CPB5000
for high precision pressure calibration of pressure gauges, pressure transmitters, pressure switches etc.
Ranges:
- pneumatic from 0.03 to 100 bar
- hydraulic from 0.2 to 4000 bar
Accuracy up to ±0.010% of READING
With integrated priming pump and spindle pump.
Piston-/cylinder-system changeable without tools
Units under test to be mounted by hand without tools
OPTION: Intelligent Calibration Module type IKM
The IKM calculates automatically the needed corrections caused by ambient influences, deviation between computed pressure and real weight of the masses, conversion to other pressure units like PSI, KG/cm² and much more. The IKM shows the user which masses to be placed on the piston to get the requested pressure, and much more...
NEW: Type LDW 1000, low-cost, hydraulic up to 1000 bar / 14500 psi, accuracy ±0.025% of measured value / reading.
|
|
The MPA series is a co-design between SCANDURA & FEM and the I.N.RI.M (Italian National Research Institute of Metrology) with the objective to develop a series of pressure balances operating in liquid media up to 120 MPa.
Two different product lines are available: BLUE and RED
Here below main features of the RED LINE are listed:
- expanded uncertainty up to 0,008% rdg
- liquid media
- different ranges up to 1200 bar
- interchangeability: MPA chassis can be used with any piston-cylinder unit and same mass set
- industrial applications
- easily transportable
|
|
The MPA series is a co-design between SCANDURA & FEM and the I.N.RI.M (Italian National Research Institute of Metrology) with the objective to develop a series of pressure balances operating in liquid media up to 120 MPa.
Two different product lines are available: BLUE and RED
Here below main features of BLUE LINE are listed:
- expanded uncertainty up to 0,005% rdg
- liquid media
- different ranges up to 1200 bar
- built in Electronic Card for the errors calculations and the measurement of the ambient parameters
- automatic motor rotation drive system for the masses
- digital mass identification system through bar-code
- Interchangeability: MPA chassis can be used with any piston-cylinder unit and same mass set
|
|
Air reference dead-weight tester BL1R Oil reference dead-weight tester BL1H
Fields:
- Chemical and Petrochemical Industry
- Food and Beverage Industry
- Pharmaceutical and Biotechnical Industry
- Heating, Ventilation and Air Conditioning
- Machine and Process Industry, Power Plants and Distribution, Automotive Industry
Type: BL1R, BL1H
Application: Calibration of pressure monitoring systems
|
|
| ... products without technical information |
| |
|
|
|
|
From CAD to mesh generation for analysis, ANSYS ICEM CFD provides sophisticated geometry acquisition, mesh generation, mesh editing, a wide variety of solver outputs and post-processing. ANSYS ICEM CFD is the only Universal pre-processor for analysis including FEA, CFD and other CAE applications such as particle transport and computational electro-magnetics. Used for engineering applications such as computational fluid dynamics and structural analysis, ANSYS ICEM CFD's mesh generation tools offer the capability to parametrically create grids from geometry in multi-block structured, unstructured hexahedral, tetrahedral, hybrid grids consisting of hexahedral, tetrahedral, pyramidal and prismatic cells; and Cartesian grid formats combined with boundary conditions. ANSYS ICEM CFD is the swiss army knife of meshing, our product vision is to provide a variety of flexible tools that can generate "any" type of mesh on "any" type of geometry for "any" solver or "any" application.
Key Features:
Intuitive built-in geometry creation and highly automated functionality for the modification and repair of imported CAD data.
Ability to work with both NURBs and faceted geometry types like STL or existing meshes.
Robust tools for creating all mesh types: hexahedral, tetrahedral, prism, pyramid, quad, tri or bar elements.
Highly tolerant of imperfect/overdetailed CAD data containing sliver surfaces, gaps, holes and overlaps (Patch Independence)
Smoothing, coarsening, refinement, element type conversion, linear or quadratic element support.
More than 100 CFD/CAE solver interface formats.
File based transfer of CFD and structural results for Fluid structure interaction simulations.
Automated batch processing through an intuitive scripting framework.
|
|
The ANSYS Fatigue Module adds the capability to simulate performance under anticipated cyclic loading conditions over a product's anticipated life span. Incorporating both Stress Life and Strain Life analyses with a variety of mean stress correction methods, including Morrow, Smith-Weston-Topper (SWT) and no mean effects, the Fatigue Module provides contour plots of fatigue life, damage, factor of safety and stress biaxiality. Additional results include rainflow matrix, damage matrix, fatigue sensitivity and hysteresis.
For Stress Life the fatigue module supports the following fatigue types:
Constant amplitude, proportional loading
Non-constant amplitude, proportional loading
Constant amplitude, non-proportional loading
For Strain Life the fatigue module supports the following fatigue types:
Constant amplitude, proportional loading
Non-constant amplitude, proportional loading
|
|
VISI Progress is dedicated software for the design of Progressive Dies and Press Tools. Industry specific functionality provides a more productive and efficient design experience. Helping the designer with intelligent decisions will reduce the potential for error and greatly improve manufacturing productivity.
|
|
|
|
|
|
Pro/ENGINEER Fatigue Advisor
Ensure reliability
Products subjected to repeated cycles of loading and unloading can fail, even if the stresses are well under safe values - a condition known as fatigue. Pro/ENGINEER Fatigue Advisor can bolster product reliability by enabling engineers to simulate and improve the fatigue performance of their designs. This reduces design iterations and costly test programs, while improving product durability. Improve your verification and validation processes with Pro/ENGINEER's advanced fatigue analysis capabilities.
Benefits
- Conduct fatigue analysis, evaluating performance measures such as life, damage, and factor of safety
- Use durability characteristics in design studies to optimize for product life
- Better understand product durability in real-world settings by specifying repeated standard loads
- Make optimal design decisions, incorporating considerations of scheduled obsolescence
- Improve product quality, reduce unplanned after-market service and warranty expenses, and avoid costly product recalls
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
