|
|
|
|
|
|
PART # SBS-IBEX
BATTERY DIAGNOSTIC TESTER
The new SBS-IBEX is a cutting edge digital battery diagnostic tester meeting all IEEE Standard Recommendations for all stationary applications such as telecommunication's back up power, utility switching power, uninterruptible power systems (UPS) and more. The new IBEX can measure the accurate internal resistance (R), voltage (V), temperature (ºC) with the world's first ripple-removing algorithm (KR PAT No. 0494489) within a short time (3 seconds or less) during flotation charge. The new IBEX has been in use worldwide with the utmost in satisfaction and reliability by end users.
The SBS-IBEX comes complete with Exmons Battery Management Software that allows the user to trend battery measurement data, export data to excel and/or create a full report with the click of a button. Note: Trended battery measurement data can detect impeding battery failures before a power backup is affected and with enough advance notice to replace the failing batteries.
ADDITONAL PARTS:
SBS-IBEX 4-PIN SET
SBS-IBEX ARM ROD
SBS-IBEX 4-POINT PIN PROBE
SBS-IBEX 2-POINT PIN PROBE
SBS-IBEX CLIP PROBE
SBS-IBEX DC CLAMP
SBS-IBEX POLY BAG
SBS-IBEX LI-ON BATTERY
SBS-IBEX SHUNT
SBS-IBEX CHARGER
SBS-IBEX CASE
|
|
The most frequent cause of damage in industrial electronic systems is overvoltages, caused either by switching actions in the equipment itself or by atmospheric discharges such as lightning. Low transfer impedance characterizes a current impulse and high transfer impedance results in a voltage impulse. To simulate both conditions, a Combination Wave Generator (CWG) delivers a voltage impulse into an open circuit and a current impulse into a short circuit. This is also known as a “Hybrid” generator.
Power network transients can be modified by the cable properties so that in a well protected domestic or commercial environment, the impulse energy adopts an oscillatory form at 100kHz. This is the “Ringwave”.
Surge testing is performed on power or communication networks, which require Coupling and Decoupling Networks (CDNs) to superimpose the impulses and provide protection for auxiliary equipment.
EMC PARTNER manufacture a range of surge generators up to 100kA and 100kV.
|
|
Two types of capacitor can be differentiated for mains applications. X capacitors, where a breakdown of the capacitor due to lightning or switching transients would not lead to an electric shock hazard and Y capacitors, used in applications where capacitor breakdown could cause a dangerous situation.
EMC Partner capacitor test systems are used to simulate transient (impulse) and active flammability tests on both X and Y capacitor types over a wide range of values.
MIG0603CAP provides impulses up to 6kV, MIG1212CAP generates 12kV higher energy impulses and MIG1803CAP is used for active flammability testing.
Capacitor testing is performed on batches of 24 samples with all values being recorded. Capacitor test systems from EMC Partner can easily be extended to include automatic switching between samples and registration of test values.
|
|
# B+K Precision Battery Capacity Analyzers tests Lead Acid Batteries and displays the batteries stored charge capacity as a percentage and displays both the loaded and un-loaded battery voltage. Models 601 and 602 can also display the battery under test’s internal resistance. These units identify batteries, which may be defective or deteriorated. They are perfect tools for testing battery back up systems for emergency lighting, alarm, sprinkler systems, UPS devices and any system using lead acid batteries to provide power. Works with 6V and 12V lead acid batteries
# Settable Ah from 1 to 100 in 1Ah steps (works best on batteries from 5 to 99Ah)
# Powered by the battery being tested
|
|
High Voltage Test Devices
Whether as a stand alone system, or part of a fully automated test system – the Elabo High Voltage Test Device sets itself apart with its wide range of applications and versatility. All test systems come ready and equipped to handle most jobs, though they can be adjusted with the appropriate plug-ins to meet further requirements. In addition to automated use, which is controlled only through an interface, there are also models with integrated touch screens available. PC-Software packages are available to assist in the assembly of complex systems, which cover all the requirements of a modern testing facility (Test Plan Creation, Visualization, Documentation, Statistics, etc.).
|
|
Testboy Profi LCD Plus
Two pole voltage tester with LC-Display
Display DC and AC voltage from 6V to 1000V Automatic measuring range selection.Single pole phase testing > 100V AC,Two pole phase sequence indication (R and L) Resistance testing up to 2000 Ohm Continuity testing up to 150 Ohm (acoustically) RCD – testing lever two button LED torch lamp
Easy operable click system to change the socket dimension from Schuko to CEE -Socket Special test tips applicable also for WAGO clamps Removable 4mm test tips adaptor Backlight lever sensor IP 65, dustproof and waterproof CAT IV 1000V IEC/EN 61243-3 (DIN VDE 0682-401) TÜV/GS tested and approved
5 years manufacturer’s warranty
|
|
The KD1E/15D is a digital HV potential indicator which can be used to indicate the presence of voltage or make voltage measurements on earthed neutral systems up to 15kV.
The potential indicator displat is powered by an integral rechargeable battery and is supplied complete with battery charger and PH3 proving unit in a bespoke carrying case
|
|
Instantaneous check on battery deterioration. Model 3555 for compact storage batteries: portable telephones and similar applications
Model 3555: support for high-capacity batteries
Model 3555: for compact storage batteries (portable telephones)
The increasing importance of battery testing
Three-rank rating of battery state: Pass, Warning, or Fail
|
|
Digital, highly advanced, multi-purpose and smart Partial Discharge and Diagnostics System for on-line and off-line PD testing on power apparatus and high voltage insulation systems, for both in-house and on-site applications.
according to the standard IEC 60270, VDE 0434, ANSI as well as various IEEE standards
PD quality tests on high voltage equipment
PD diagnosis on developing insulating materials
Designed for on-site PD diagnosis tests as well as for manufacturing and research
PD fault location for power cables
|
|
SGDA impulse test systems can be used to generate impulse voltages simulating lightning strokes and switching surges.
The stage energy is 5 or 10 kJ. Max. charging voltage is 3MV.
Applications covered include testing according to IEC, ANSI/IEEE as well as other national standards. The basic system can be upgraded in various ways for special tests and for greater ease of operation. A number of additional circuits and components allow optimising the impulse test system for tests on different kind of high voltage test objects.
The generator is due to its unique, modular, patented structure (the D-shaped generator body also forms the enclorsure for the sphere gaps) perfectly suited for transportation and easy on-site erection. Also the internal inductance is the lowest ever built
|
|
For testing the insulating strenght of transformers, motors, electric
machines and electrical plants and equipment.
|
|
| ... products without technical information |
| |
Willtek Secures Railway Safety
Based on the Willtek 4200, the Willtek 4202R Mobile Service Tester is dedicated to new features and frequency bands introduced by GSM-R, the railway communication system based on GSM. The Willtek 4202R is the first GSM-R test instrument for service applications, and its small size and low weight make it the ideal choice to test and repair applications requiring mobility.
Proper Performance Helps Emergency Situations
The Willtek 4202R allows the simulation of group calls (VGCS) at various priority levels. This includes emergency calls based on group calls to verify not only the performance of the cab radios, but also of peripherals such as optical and acoustical alarms. These tests ensure proper performance of the radio system and help prevent disaster in emergency cases.
|
|
|
|
|
|
901 TDR LAN Cable Tester
Handheld TDR Meters
Model 901 is specially designed to speed up the onsite testing of data networks and production testing of cable assemblies. The meter quickly tests shielded and unshielded LAN cables and identifies all commonly found Pair, Split Pair, and Reversed Pair. Digital display shows these 5 common wiring faults and the provided 1 Female RJ45 to Female BNC remote identifier will make wire-mapping a breeze.
Features:
- Accurate to 2" (5 cm) throughout the entire range up to 2,000 ft (600 m).
- Digital Display shows 5 common wiring faults: Open Pair, Shorted Pair, Crossed Pair, Split Pair, and Reversed Pair.
- Includes 1 remote identifier for wire mapping.
- Extra-large backlit (ICON type 7 segment) LCD.
- Automatic output impedance control, auto-range, auto-zero and auto-sensitivity allows for closely matching to a wide range of cables under test. Only V.O.P (Velocity of Propagation) settings required.
- User-friendly menu on screen operation for easy-to-use.
- Measuring capability of the V.O.P of a sample cable.
- 20 internal memory locations store up to 20 traces for future analysis.
- Internal library of 39 standard cables.
- Tone Generator (Oscillating 910 to 1100 Hz with 5 Vp-p).
- Line Voltage Detection: Displays "OUCH" message and stops operation if line voltage exceeds 6.5 V.
- Safety Protection (up to 250 V RMS).
|
|
|
|
|
|
|
The DMM is a professional instrument with TRMS measurement of AC/DC voltage, AC/DC Current (through external clamp), Resistance and Frequency. Additional features are MAX/MIN/AVG function, HOLD function and PEAK detection with Response Time of 1ms, useful for surge currents detection. The Safety Tester features allow to perform test on electrical plants according to VDE0413. Measures of Continuity, Insulation, Global Earth value (also with 0.1W resolution), RCDs test, phase sequence indication and phase coincidence (using only one Test Lead even just touching even insulated cables or two Test Leads) and Leakage current (with HT96U clamp + NOCANBA connector) will be easily performed thanks to this new extremely compact instrument. An innovative function (AUTOTEST) automatically performs main safety checks in the plant (Earth Resistance measurement, RCD Test, Insulation Test) just connecting the instrument to a socket and pressing the TEST button. The instrument will give you a final response (OK or NOT OK) about the safety of the plant under test. Finally the LAN checker function allows you to check if the wire mapping in a LAN cable is correct or not with easy indications about the found errors, which will guide you though the troubleshooting. M75 is completed by a modern selector function knob, a large numeric display for easy readings of measurements and a protection rubber holder to prevent accidental damaged.
|
|
The ultimate platform for network experts. Combines physical, optical, transport and datacom testing in a single box. Perform simultaneous acquisitions and fast data post-processing, and benefit from a scalable range of test applications and field-interchangeable modules.
Key Features and Benefits
Five configurations (two-slot, four-slot, seven-slot, eight-slot and bus protector), providing maximum flexibility for long-haul, metro, DWDM, high-fiber-count, Ethernet, SONET/SDH or DSn/PDH test applications
Pentium-powered, with up to 512 MB memory
Easy-to-read, high-resolution 12.1 inch TFT screen
Windows® operating system
Simultaneous acquisitions and fast data post-processing
|
|
|
LeCroy's oscilloscopes can be turned into mixed-signal oscilloscopes (MSOs) with the addition of the MS-500 or MS-250 mixed-signal oscilloscope options. In addition, I2C, SPI, UART, RS232, LIN, and CAN triggering and decoding options turn these oscilloscopes into all-in-one analog, digital, and serial data trigger, acquisition, and analysis machines.
|
|
The VC200 is the ideal tool for testing GSM/WCDMA Mobiles during manufacture, maintenance, servicing, troubleshooting and point of sale.
Low cost GSM/W-CDMA mobile phone tester
- Supports all GSM & W-CDMA frequency bands
- Signaling tester mode
· Auto test mode
· Manual test mode
- Tx/Rx Tester mode
- Suitable for manufacture, maintenance and servicing
- Compact and lightweight
|
|
|
|
|
|
2201 ProLock
The 3G mobile phone tester for repair shops
Willtek’s 2201 ProLock is a reasonably priced test instrument for 3G mobile phones and wireless data cards. Level 1 and level 2 service shops use ProLock to quickly test wireless devices, perform smaller repairs and bill manufacturers for warranty claims.
The 2201 ProLock is similar to the 4100 and 4200 series instruments because it is small, easy to use and affordable to large mobile phone retailers with a repair shop in the back office. ProLock, however, supports both GSM and WCDMA phones and wireless devices. Many mobile phones today include WCDMA functionality; manufacturers start to demand WCDMA testing in case of warranty claims from repair shops. ProLock fills the gap between the cheap GSM-only testers and sophisticated 3G test sets!
Repair shops and manufacturers benefit
Local, small and medium size repair shops have been replaced by centralised repair factories. This led to customer dissatisfaction and high cost for small repairs or in the No Fault Found case. With the 2201 ProLock, smaller repair shops filter out these phones and return them to the customer almost immediately, resulting in satisfied customers and low cost of reverse logistics.
|
|
|
|
|
|
Willtek offers solutions for the test of mobile phones. Our solutions address the RF performance of the phone. Willtek offers different solutions, depending on the application:
Point of Sale / Point of Return - Go/NoGo testing
Very often phones returned into the service loop are not having any technical problems, the problems are more to do with bad coverage or "manual not read" syndrome. In order to prevent these phones being returned for service , testing should be done at a very early stage at the point of sale or point of return. Willtek's Go/NoGo testers are well known for their ease of use and uncomplicated user interface. Despite the simple user interface, the test sets are performing measurements according to the respective standards (e.g. GSM, CDMA2000, etc.)
Service and Repair Workshops
Because time and test speed are critical for today's service and repair shops, it is important to have a flexible test set which can test and align many different phones - and support the specific measurement routines required by different manufacturers. Willtek's test solutions are designed with a multi-technology platform, allowing them to invest in one instrument that supports all of today's technologies.
Manufacturing
In manufacturing time and simplicity of testing is crucial. Manufacturers focus on simple RF measurements to tune and align the phones. Willtek's test solutions provide fast, easy testing while providing comprehensive results. And as with our other solutions, the multi-technology platform helps manufacturers preserve their test equipment investment.
|
|
|
|
|
|
2303 Stabilock
Regular testing of TETRA phones ensures safe and reliable communication
In critical situations, users in the public safety and security sector fully rely on their communication devices. To help organisations such as police, fire brigades and paramedics provide maximum safety and reliability to their users, Willtek designed the 2303 Stabilock. It is the first TETRA mobile station tester which is specifically made for testing TETRA radios in a service environment. Service managers can now use the affordable instrument to ensure that the radios are fully operational; this is particularly important for the police, fire brigades and paramedics where lives may depend on proper communication tools!
The 2303 Stabilock delivers precise results the fast way. No matter if Trunked Mode or Direct Mode (optional), 400 or 800 MHz band: After setting up network parameters and frequency range the tester is ready for operation. The high contrast 6.5” TFT colour display is split into four sections for clear reading of test results in numeric or graphic format. All settings and commands are accessible via six softkeys or with one-hand operation using the turn-and-push dial. Reducing TETRA complexity to what is really needed in service – with this operational concept, users can operate the instrument easily with a few key presses on the Stabilock’s high-quality click-type keyboard. Alternatively, a standard USB mouse provides access to all screen elements as on a PC.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
