|
|
| Very High speed load cell interface that was especially designed for WIM application either trucks or trains. The LCIC-WIM comes with embedded application calculates "on the fly" the axle weight, axle speed and distance between axles. With 52000 samples per second high resolution A/D and powerful DSP that runs the WIM application on board, it consider to be the fastest and most intelligent Load Cell Interface that is available today in the market. The LCIC-WIM equipped with USB and RS232/485 and comes with drivers and full examples on how to communicate with the board and our monitoring package that helps to analyze the scale behavior under different speeds. |
|
| Very High speed load cell interface that was especially designed for WIM application either trucks or trains. The LCIC-WIM comes with embedded application calculates "on the fly" the axle weight, axle speed and distance between axles. With 52000 samples per second high resolution A/D and powerful DSP that runs the WIM application on board, it consider to be the fastest and most intelligent Load Cell Interface that is available today in the market. The LCIC-WIM equipped with USB and RS232/485 and comes with drivers and full examples on how to communicate with the board and our monitoring package that helps to analyze the scale behavior under different speeds. |
|
| ... products without technical information |
| |
ADVANTAGES:
• Robot checking of Electrode Force
• No need to stop robot cells for force checking
• Very fast payback
• Alerts operators to immediate faults & variations
• Can eliminate scrap due to weld deterioration
• Reduces equipment damage and wear
• Keeps force within preset limits
• Gives early warning of equipment deterioration
• Continuous robot operation via go/no go signals
DESCRIPTION - KR1000:
Stand alone analogue output force sensor. Supplied for direct plug and play replacement to commonly existing units.
The target pads remain spatially the same. Robot reprogramming for test position is not required.
The monitor is preset to Zero on no load but can be simply adjusted by the user if required.
The innovative design of the KR1000 force head makes it far less susceptible to errors induced by electrodes not being perpendicular to the target pads.
Exacting construction standards guarantee this instrument is of greater accuracy than other monitors of this kind.
Multiple testing during construction further assist in achieving the superiority that we have set out to achieve.
When coupled to its onboard electronics package the sensor is preset for zero load & calibrated
to a known (NPL) standard.
The KR1000 is robust, durable, reliable, and accurate. KR1000’s have been installed on Car Manufacturing lines since 2005 and have been in constant use without failures. |
|
Hand Held Electronic Force Gauge
An ergonomically designed hand held force gauge.
ADVANTAGES
User comfort "'Ergonomically" designed - for ease of use
One piece unit
Very high accuracy
Swivel head allows access to difficult to reach positions
As with all welding procedures, it is important to eliminate as many variables as possible in order to achieve optimum welding consistently over long periods.
Electrode force is one of the critical parameters in obtaining repeatable, reliable resistance spot welds.
Force can vary because of variable factory air pressure, water in the air lines causing air cylinders to deteriorate and loss of air pressure due to worn seals.
This self contained instrument uses a cell with a force sensor to provide accurate digital read out for auditing weld electrode forces.
Accuracy of this instrument is better than 0.2% and can be switched to read 0-2000 kg, 0-20.00 kN or 0-4400lbs.
In cases of difficult access the head of the swivel head gauge can be swiveled at least ±72º up or down and rotates at least ±90º. Once the desired position is reached it can be fixed by a simple hand tightened knob. A 90 mm long handle is provided for optional use with 2 mountain positions either in-line or at 90º.
A support wrist strap is attached to the gauge so that in the event that it is forced out of the operators hand by misaligned electrodes, it need not fall to the floor and be damaged. |
|
Faults in welding tongs or incorrect process parameters in welding can result in production line waste or defective parts. Checking the electrode force periodically permits spark malfunctions to be detected at an early stage so that repairs can be carried out in good time.
The new Type 9833A test sensor allows precise and reliable measurements to be carried out with minimal electrode gaps. The built-in charge amplifier simplifies the task of mounting and helps to ensure the reliability required by the automobile industry.
|
|
Several Resistance Welding Accessories:
Welding Handpieces
Footpedals and Footswitches
Optics and Illumination Accessories
Electrode/Material Selection Guide
Electrode Force Gages
Electrodes
Unibond and Unitip Electrodes
Kovar Ribbon/Polishing Disks
Cables, Terminals, Connectors and Adapters
Electrode Holders and Adapters |
|
The quality of a spot weld depends on the force applied by the electrodes together with the value of the welding current. For control programs, measuring the force applied by the electrodes is extremely important for maintaining constant production conditions. The Welding Tester instrument is designed for measuring the closing force on welding heads, which can be used either for setting up or for periodical maintenance. The tips are exchangeable for measuring the force applied by different forms of electrodes; the lowest closing dimension is 3 mm.
Different models are available for measuring 0–5000N up to 0-20000N. The new tool has all the ruggedness, quality and accuracy of the other tools in the CENTOR family, specially designed for taking “nomad” measurements in production shops.
|
|
| ... products without technical information |
| |
X-Ray Sensors offer a number of advantages over beta and gamma sensors, including greater precision, better streak detection, long-term stability and non-nuclear technology.
Since the X-ray sensor's energy output can be changed via digital power regulation, it can be optimized to run very efficiently over a wide range of product weights and thicknesses. |
|
The sensor is suited for torsion measurements and the measurement of reaction moments for orthopaedic measuring devices. It is applicable for measurements of friction forces.
The strain gauge full bridge measure the torsion movement appearing in the tube of the lattice structure. |
|
|
|
see the results for the following category
