|
|
The OIML certified beam load cells SD are used for general weighing in tough environments, in bench- and platform scales, belt scales and in production equipment.
* Accuracy classes C1, C2, C3, C6 (MI10) to OIML R60
* High overload and sideload capacity 250 to 1.000 %
* Uncomplicated mechanical installation without protecting devices
* Patented high reliability sensor - stainless steel, laser welded to IP68
* Uncomplicated electrical installation - coax cable only
* RS485, Profibus DP, DeviceNet, Modbus to PLC's, PC's, etc. and OIML certified weighing displays
* Withstands welding voltages and ESD to IEC 1000-4-4
* ATEX approved version available (type SDE)
|
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
FUTEK, a leading manufacturer producing a huge selection of Load Cells, utilizes one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.
FUTEK's strain gauge based load cells are widely known in many industries to contain:
-The Highest accuracy which may conform to many standards from the Automotive to Aerospace.
-Robust Construction made of either high strength Stainless steel or Aluminum.
-A guarantee to perform at longest possible work life even at the most rigorous conditions
-A plethora of mounting options for ANY scale ANY-where.
-Competitive pricing that separates Futek Advanced Sensor Technology from the rest.
-A full gamut of selections with capacities ranging from 10 grams to 1 MILLION pounds.
FUTEK's industry listing is as broad as its Sensor selection. Our selection of load cells can be categorized by the following styles:
-AUTOMOTIVE RELATED (i.e. auto test measure devices: pedal, shifting, multi axial)
-BENDING BEAM
-COLUMN/CANISTER
-DONUT
-FOLD BACK BEAM
-FORCE SENSOR
-LOAD/FORCE WASHER
-LOAD BUTTON
-MEDICAL RELATED
-OVERLOAD PROTECTION
-PANCAKE
-S BEAM/ Z BEAM
-THREAD FEMALE MOUNT
-THREAD MALE MOUNT
-THRU HOLE
-CLEVIS PINS
|
|
DS Europe produces load cells with built-in analog and digital electronics.
Measuring ranges:from 0 to 6Kg up to 500tons max.
Outputs: CANOpen, RS485, RS422, 5V, 10V, 4-20mA, 2mV/V.
Advantages: high resolution (A/D converter 24bit max.), high sampling rate (from 7,5 upt to 960Hz max.), electrical noise protection, compactness, digital alarms, digital filter, zeroing, easy to service (overload memory).
Applications: automation, textile machines, medical machines, machine tools, presses, vehicles, weighing, food machines, quary machines, agricolture machines, research, machines working paper-wood-plastics-rubber etc. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
DS Europe manufactures load cells with built-in CE marked electronics with analog or digital outputs.
All load cells with non amplified output 2mV/V have a built in calibration circuitry that electrically simulates a known value of force shown in a certificate ( making It easy and quick to calibrate with the external electronics getting the signal ).
Series 500QD single point load cells Ranges (tension and compression): from 0 up to ±2 ... 2000Kg FS.
Built-in electronics (option): analog or digital outputs.
Environmental protection: IP65.
Compensated against off-center forces.
Series AP7000 compact column load cells Series AP7000 tension and compression load cell.
Ranges: from 0 up to 250-500Kg 1-3-5-10-25-50-100 tons.
Built-in electronics (option): analog or digital outputs.
Environmental protection: IP65. |
|
DS Europe produces general purpose miniaturised load cells.
Measuring ranges: 0 to 3 up to 2000Kg.
Output: 2mV/V.
Applications: automation, medical machines ( dialisis, radiology, blood transfusion machines, dentist tools, hospital beds, stabilometry platforms etc.), textile machines, machines working paper-rubber-plastics, weighing, machine tools and wherever is required compactness. |
|
For over a decade, FUTEK Advanced Sensor Technology has been supporting the Automotive Industries’ sensor requirements in endurance testing, validation, verification and qualification. Our Automotive Load Cells are designed to fit a wide range of applications from component testing to full assembly. Specialty products such as our Low Profile Spike Resistant Pedal Force Sensor, Bi-Axial Stick Shift Sensor, and Compact Seat Belt Sensor are selected and fully trusted product throughout the Automotive Industry.
Any of our Automotive Load Cells can be easily modified or customized to meet your requirements. The standard models are often available in our stock making it available for 24 hour shipping. All Load cells and Force Transducers are manufactured in the US. All Sensors are available with in-line signal conditioned amplifier and or TEDS / IEEE1451.4 option.
• Custom Strain Relief
• One piece construction suitable for endurance testing
• Low Profile Height
• Light Weight
• Available in Tension, Compression, and Multi-Component Loads
• Removable Mounting Plate
• Spike Resistant
• Excellent Off Center Loading
• Operating Temperature of -60° F - 200° F
• Capacity ranging from 10 lb to 100,000 lbs
• Utilizes Metal Foil Strain Gauge Technology
|
|
- Handheld Readouts.
- Made from a Lightweight Aerospace Alloy.
- Available Hermetically sealed for use in wet conditions.
- Tare, Peak and Reset facility.
- Units have a 5 metre cable close coupled to a 4 digit 15mm LCD display.
- All units are calibrated to comply with ISO 7500-1: 2004.
- The accuracy of the cells are better than 1% of applied load.
- The power source is a 9V PP3 battery, can be supplied for
mains power if required (240v).
- 12 Month Guarantee, subject to conditions.
- Complete with carry case. |
|
Load Cells manufactured in US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Load Cells, utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.
A Load Cell is defined as a transducer that converts an input mechanical force into an electrical output signal. Load Cells are also commonly known as Load Transducers or Load Sensors. |
|
| Our load cell uses proprietary sputtered thin film strain gauge technology to create a rugged sensor with exceptional long term stability. These highly sophisticated sensors are manufactured in high quantities using state-of-the-art equipment. |
|
Digital load cells on the basis of the strain gage technology provide new impetus for the areas of dynamic weighing, sorting, filling, and dosing. In addition to all relevant functions for standard weighing processes, the intelligent load cells also provide control functions for sorting, filling, and dosing processes. Using a RS 232 or RS 485 4-wire interface, all relevant data can be accepted as a filtered, scaled, and digitized output signal directly into the control system used. And that at a fast measuring rate of up to 600 measurements per second.
|
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
- Handheld Readouts.
- Made from a Lightweight Aerospace Alloy.
- Available Hermetically sealed for use in wet conditions.
- Units have a 5 metre cable close coupled to a 4 digit 15mm LCD display.
- Tare, Peak and Reset facility.
- The power source is a 9V PP3 battery, can be supplied for mains
power if required (240v).
- All units are calibrated to comply with ISO 7500-1: 2004.
- The accuracy of the cells are better then 1% of applied load.
- Complete with carry case.
- 12 Month Guarantee, subject to conditions. |
|
Load cells work like calibrated springs.
A force is applied and there is a flexion: there is a Wheatstone bridge with strain gauges that measure this mechanical flexion thence giving a proportional electrical signal.
DS Europe can also manufacture load cells with built-in CE marked electronics with analog or digital outputs.
All load cells with non amplified output 2mV/V have a built in calibration circuitry that electrically simulates a known value of force shown in a certificate ( making It easy and quick to calibrate with the external electronics getting the signal ). |
|
CM Load cell for compression applications
Range of measurement: from 100 to 50,000 Kg
Accuracy class: 0.1%
All stainless steel construction
Corrosion resistant
Internally generated calibration signal
Grade of protection: IP67 (DIN 40050)
TH Force transducer for tension/compression applications
Range of measurement: from 10 to 100 kN
Accuracy class: 0.1%
All stainless steel construction
Corrosion resistant
Internally generated calibration signal
Grade of protection: IP65 (DIN 40050)
|
|
HBM offers a comprehensive range of load cells and force transducers for weighing and force measurement applications, including customized solutions. All sensors are designed to work perfectly with our innovative measuring amplifier systems and our intuitive operating and
analysis software.
Load Cells
HBM weighing technology components can be found in almost all industries where goods are produced, processed or checked:
In the industrial production and scale equipment
In the manufacture of building materials
In the production of food and consumer goods
In the manufacture pharmaceutical products
In medical engineering.
Official PTB-approved certificates (the PTB is the national institute of natural and engineering sciences, and the highest technical authority for metrology and physical safety engineering in Germany) are available for a large number of load cells. Appropriate certificates are also available for worldwide use.
All standard load cells are available in accordance with European directive 94/9/EC (ATEX95).
Force Transducers
HBM force transducers are used today in every sector of industry and for R&D activities:
In the field of stress analysis
In manufacturing automation
In materials testing
In calibration.
|
|
| Honeywell Sensotec manufactures tension and compression load cells to cover a full range of applications. Rugged and fully welded, these stainless steel units provide accuracy up to 0.02% over ranges from 25 grams to 3 million pounds. Available unamplified, amplified or with digital output. |
|
The Load-Force-Weight Sensor family is a complement to Magtrol's range of load measuring pins. These sensors can be used in different applications where the load measuring pin cannot be mounted. Our various executions and precision classes provide you with great flexibility for your application.
Used with our load monitoring unit or signal conditioners, Magtrol Load-Force-Weight Sensors constitute an ideal load and weighing measurement system which continuously checks for defined loads and overloads.
|
|
The load cell is the heart of the weighing instrument.
Our wide range can meet all you needs :
Bending beam load cell FA 3000 i
traction type load cell TA-I / TVN
Shear beam load cell CMA-S / CMI
Digital compression load cell ASL
Compression type load cell SCL 35/55 t
Compression type load cell CSP-M
Compression type load cell TSL |
|
| We have a comprehensive range of general purpose and specialist load cells including low range precision sensors and high capacity load cells. |
|
| Sartorius offers bending beam, compression and shear beam load cells as well as tension load cells, among others, for a wide variety of applications. |
|
SCAIME offers a wide range of load cells allowing to provide the best solution for all the weighing applications.
- Capacities from 1kg to 200t
- OIML R60 approval up to 6000d
- All modes of demounting of load:
Single point
Compression
Bending, shear beam
Traction
- Different materials and degrees from protection allowing to optimize the cost ratio/performance
- Complete range Certified ATEX
|
|
| You are working on an industrial application where you need "Force transducers"? A whole range of transducers can be integrated in your project easily. Your machine is operated by tension and/or compression force. Just have a look in the table hereunder? The Force transducer you are looking for is most certainly available. Do you need further information regarding the use of our load cells? Natural Frequency? Accuracy? Use in radio-active environments? If the solution isn’t present on our website, don’t hesitate to contact our team of Sales Engineers. If you have a question, you’ll get the answer! Don’t forget to look at our customised solutions, because flexibility is part of our philosophy. Just test us. We guarantee a quick and professional advise /quotation. |
|
| Whether you need conventional solutions for regular tasks or you want to weigh something in a difficult location, Schenck Process, provides you everything you need from the standard unit to the weighing sensors that are capable of turning practically anything into a scale all from one source. Accuracies range from ± 0,05% to the highest precision legal-for-trade C5 and C4 Mi-7.5 (± 0.01%); we can provide the accuracy that meets your needs. For low weighing values from 5kg (11.02 Ibs) to heavy weigh values of 470 tons [metric] (518 tons [short]). Regardless of the environment where you intend to set up the weighing forms and installation conditions. Be it hazardous area applications, environmental conditions that require protection types up to IP 68 or hot applications with temperatures of up to 150°C (302°F). |
|
| The S400 range of 'button' style load cells was designed for those force measurement applications where space is at a premium. Constructed from 17-4PH stainless steel, the devices are available in full scale capacities from 50 lb to 1000 lb and are complete with shielded cable to custom lengths. |
|
This Low Profile Tension & Compression Load Cell has high accuracy. It has Nonlinearity of ±0.1%, Deflection of 0.003" nominal and Operating temperature of -60° F to +200° F. The standard LRF300 Low Profile Tension & Compression Load Cell can be modified or customized to meet your requirements and most capacities are in our inventory, making them available for 24 hour shipping. Similar to our entire Load Cell product line this model is manufactured in USA and uses metal foil strain gauge technology.
Product Highlights:
Light Weight
Low Deflection
2024 Aluminum Construction
In both Tension & Compression
Low capacity applications
Utilizes Metal Foil Strain Gauge Technology |
|
| SMD can manufacture a load cell or force sensor to measure anything, even something as complex as the human eye! Our load cells are designed and manufactured using our own proprietary thin film strain gauge process for greater stability and accuracy. Our load cell applications include weighing scales, non-invasive medical sensors, pharmaceutical testing, aerospace and industrial measurements. Whether you need an "off the shelf" load cell or custom engineered load-cells, let SMD design an ultra low profile, button style or overload proof sensor for you. We are the world leader in miniature load cells and low profile load cells. |
|
|
