|
|
The OIML certified beam load cells SD are used for general weighing in tough environments, in bench- and platform scales, belt scales and in production equipment.
* Accuracy classes C1, C2, C3, C6 (MI10) to OIML R60
* High overload and sideload capacity 250 to 1.000 %
* Uncomplicated mechanical installation without protecting devices
* Patented high reliability sensor - stainless steel, laser welded to IP68
* Uncomplicated electrical installation - coax cable only
* RS485, Profibus DP, DeviceNet, Modbus to PLC's, PC's, etc. and OIML certified weighing displays
* Withstands welding voltages and ESD to IEC 1000-4-4
* ATEX approved version available (type SDE)
|
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
Eilersen Electric also offers its expertise to customers with special requests where the capacitive technology can often be the solution to challenging applications.
Examples of customized solutions are: Stress measurements in roller bearings, Web tension measurements in paper and plastic foil manufacturing equipment, Monitoring of construction equipment, Load measurements in commercial vehicles etc.
* Classes OIML C1 to C6
* Atex versions
* Uncomplicated mechanical installation without protecting devices
* High overload and sideload capacity up to 1000 %
* Patented high reliability sensor - stainless steel, laser welded to IP68
* Uncomplicated electrical installation - coax cable only
* RS485, Profibus, Devicenet, CAN bus to PLC's, PC's, etc. and EE instrumentation
* 32 bit data word does away with dead weight compensation
* Withstands welding voltages and ESD to IEC 1000-4-4 |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
When a FANUC Robot is fi tted with the FANUC „Force Sensor”, it enables the robot to perform High Precision assembly operations such as meshing of gears and close tolerance insertion of parts.
The Force Sensor can also be utilised when the robot is used to perform precision grinding and polishing applications.
FORCE GUIDED INSERTION
Force Control allows the insertion of shafts and pins into matching holes using the force sensor.
FORCE GUIDED PHASE MATCHING
The Force Control enables the assembly of gears and other mechanical components via phase matching.
FORCE CONTOURING
This function controls the force so that the robot constantly pushes the surface along the taught trajectories. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
FUTEK, a leading manufacturer producing a huge selection of Load Cells, utilizes one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.
FUTEK's strain gauge based load cells are widely known in many industries to contain:
-The Highest accuracy which may conform to many standards from the Automotive to Aerospace.
-Robust Construction made of either high strength Stainless steel or Aluminum.
-A guarantee to perform at longest possible work life even at the most rigorous conditions
-A plethora of mounting options for ANY scale ANY-where.
-Competitive pricing that separates Futek Advanced Sensor Technology from the rest.
-A full gamut of selections with capacities ranging from 10 grams to 1 MILLION pounds.
FUTEK's industry listing is as broad as its Sensor selection. Our selection of load cells can be categorized by the following styles:
-AUTOMOTIVE RELATED (i.e. auto test measure devices: pedal, shifting, multi axial)
-BENDING BEAM
-COLUMN/CANISTER
-DONUT
-FOLD BACK BEAM
-FORCE SENSOR
-LOAD/FORCE WASHER
-LOAD BUTTON
-MEDICAL RELATED
-OVERLOAD PROTECTION
-PANCAKE
-S BEAM/ Z BEAM
-THREAD FEMALE MOUNT
-THREAD MALE MOUNT
-THRU HOLE
-CLEVIS PINS
|
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
Multi-component force measurement places high demands on the measuring device. The characteristics of the force vector to be measured largely determine the result. The size and direction of the force application point, as well as the dynamics, should have as little effect as possible on the process.
With the new Kistler Type 9327, 9347, 9367 and 9377 sensors, our company's established experience and know-how is now available even for multi-component force measurements carried out by the customer. The precisely preloaded measuring elements are easy to fit and, as they come ready calibrated from the factory, they can be used immediately for multi-component force measurements.
|
|
Series 261A
Triaxial 3-component dynamic force link, ICP®
- Automotive Chassis and Other Vehicle Dynamic Measurements
- Monitor Cutting Tool Forces and Detect Tool Wear
- Provide Feedback for Force Limited Vibration Testing
- Measure Input Forces for Modal and Structural Testing
- Measure Impact Forces During Drop Testing and Crash Testing |
|
DS Europe produces load cells with built-in analog and digital electronics.
Measuring ranges:from 0 to 6Kg up to 500tons max.
Outputs: CANOpen, RS485, RS422, 5V, 10V, 4-20mA, 2mV/V.
Advantages: high resolution (A/D converter 24bit max.), high sampling rate (from 7,5 upt to 960Hz max.), electrical noise protection, compactness, digital alarms, digital filter, zeroing, easy to service (overload memory).
Applications: automation, textile machines, medical machines, machine tools, presses, vehicles, weighing, food machines, quary machines, agricolture machines, research, machines working paper-wood-plastics-rubber etc. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
DS Europe manufactures load cells with built-in CE marked electronics with analog or digital outputs.
All load cells with non amplified output 2mV/V have a built in calibration circuitry that electrically simulates a known value of force shown in a certificate ( making It easy and quick to calibrate with the external electronics getting the signal ).
Series 500QD single point load cells Ranges (tension and compression): from 0 up to ±2 ... 2000Kg FS.
Built-in electronics (option): analog or digital outputs.
Environmental protection: IP65.
Compensated against off-center forces.
Series AP7000 compact column load cells Series AP7000 tension and compression load cell.
Ranges: from 0 up to 250-500Kg 1-3-5-10-25-50-100 tons.
Built-in electronics (option): analog or digital outputs.
Environmental protection: IP65. |
|
DS Europe produces general purpose miniaturised load cells.
Measuring ranges: 0 to 3 up to 2000Kg.
Output: 2mV/V.
Applications: automation, medical machines ( dialisis, radiology, blood transfusion machines, dentist tools, hospital beds, stabilometry platforms etc.), textile machines, machines working paper-rubber-plastics, weighing, machine tools and wherever is required compactness. |
|
Sensortechnics is a leading manufacturer and distributor of a wide range of sensors and fluid control devices. The product portfolio includes basic pressure sensors, rugged transmitters, submersible level sensors and customised pressure sensing systems from 1 mbar up to 1000 bar as well as liquid level switches, oxygen, flow and force sensors. Additionally, Sensortechnics offers ultrasonic air bubble, air-in-line, liquid level and fluid monitoring sensors and detectors. Fluid control devices include miniature solenoid valves and diaphragm pumps, electronic pressure controllers and custom specific fluidic control systems.
Sensortechnics has more than two decades of experience in providing highly customised sensing products and in the development of complex integrated fluid control systems for OEM customers worldwide. |
|
For over a decade, FUTEK Advanced Sensor Technology has been supporting the Automotive Industries’ sensor requirements in endurance testing, validation, verification and qualification. Our Automotive Load Cells are designed to fit a wide range of applications from component testing to full assembly. Specialty products such as our Low Profile Spike Resistant Pedal Force Sensor, Bi-Axial Stick Shift Sensor, and Compact Seat Belt Sensor are selected and fully trusted product throughout the Automotive Industry.
Any of our Automotive Load Cells can be easily modified or customized to meet your requirements. The standard models are often available in our stock making it available for 24 hour shipping. All Load cells and Force Transducers are manufactured in the US. All Sensors are available with in-line signal conditioned amplifier and or TEDS / IEEE1451.4 option.
• Custom Strain Relief
• One piece construction suitable for endurance testing
• Low Profile Height
• Light Weight
• Available in Tension, Compression, and Multi-Component Loads
• Removable Mounting Plate
• Spike Resistant
• Excellent Off Center Loading
• Operating Temperature of -60° F - 200° F
• Capacity ranging from 10 lb to 100,000 lbs
• Utilizes Metal Foil Strain Gauge Technology
|
|
- Handheld Readouts.
- Made from a Lightweight Aerospace Alloy.
- Available Hermetically sealed for use in wet conditions.
- Tare, Peak and Reset facility.
- Units have a 5 metre cable close coupled to a 4 digit 15mm LCD display.
- All units are calibrated to comply with ISO 7500-1: 2004.
- The accuracy of the cells are better than 1% of applied load.
- The power source is a 9V PP3 battery, can be supplied for
mains power if required (240v).
- 12 Month Guarantee, subject to conditions.
- Complete with carry case. |
|
Load Cells manufactured in US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Load Cells, utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.
A Load Cell is defined as a transducer that converts an input mechanical force into an electrical output signal. Load Cells are also commonly known as Load Transducers or Load Sensors. |
|
Responding to specific projects is a part of our strength.
Are you looking for a solution for which no available component is to be found on the market? We will help you solving your problem by means of one of the special load cells we already realized or by developing a custom made model. Our design team will assist you in your project, from its very beginning till its complete realisation. Designing and realizing new solutions are our specialties; it belongs to our company's culture. During the last years, we have developed more than 1500 models and applications, from single part till medium and great serial production. We can present you a documented proposal including quotation within short time.
Even a part of an existing machine can, under certain conditions, become a force transducer measuring tension or compression. Transducers that will respond to your need at particularly competitive prices.
|
|
| Our load cell uses proprietary sputtered thin film strain gauge technology to create a rugged sensor with exceptional long term stability. These highly sophisticated sensors are manufactured in high quantities using state-of-the-art equipment. |
|
Responding to specific projects is a part of our strength.
Are you looking for a solution for which no available component is to be found on the market? We will help you solving your problem by means of one of the special load cells we already realized or by developing a custom made model. Our design team will assist you in your project, from its very beginning till its complete realisation. Designing and realizing new solutions are our specialties; it belongs to our company's culture. During the last years, we have developed more than 1500 models and applications, from single part till medium and great serial production. We can present you a documented proposal including quotation within short time.
Even a part of an existing machine can, under certain conditions, become a force transducer measuring tension or compression. Transducers that will respond to your need at particularly competitive prices. |
|
Digital load cells on the basis of the strain gage technology provide new impetus for the areas of dynamic weighing, sorting, filling, and dosing. In addition to all relevant functions for standard weighing processes, the intelligent load cells also provide control functions for sorting, filling, and dosing processes. Using a RS 232 or RS 485 4-wire interface, all relevant data can be accepted as a filtered, scaled, and digitized output signal directly into the control system used. And that at a fast measuring rate of up to 600 measurements per second.
|
|
ADVANTAGES:
• Robot checking of Electrode Force
• No need to stop robot cells for force checking
• Very fast payback
• Alerts operators to immediate faults & variations
• Can eliminate scrap due to weld deterioration
• Reduces equipment damage and wear
• Keeps force within preset limits
• Gives early warning of equipment deterioration
• Continuous robot operation via go/no go signals
DESCRIPTION - KR1000:
Stand alone analogue output force sensor. Supplied for direct plug and play replacement to commonly existing units.
The target pads remain spatially the same. Robot reprogramming for test position is not required.
The monitor is preset to Zero on no load but can be simply adjusted by the user if required.
The innovative design of the KR1000 force head makes it far less susceptible to errors induced by electrodes not being perpendicular to the target pads.
Exacting construction standards guarantee this instrument is of greater accuracy than other monitors of this kind.
Multiple testing during construction further assist in achieving the superiority that we have set out to achieve.
When coupled to its onboard electronics package the sensor is preset for zero load & calibrated
to a known (NPL) standard.
The KR1000 is robust, durable, reliable, and accurate. KR1000’s have been installed on Car Manufacturing lines since 2005 and have been in constant use without failures. |
|
Hand Held Electronic Force Gauge
An ergonomically designed hand held force gauge.
ADVANTAGES
User comfort "'Ergonomically" designed - for ease of use
One piece unit
Very high accuracy
Swivel head allows access to difficult to reach positions
As with all welding procedures, it is important to eliminate as many variables as possible in order to achieve optimum welding consistently over long periods.
Electrode force is one of the critical parameters in obtaining repeatable, reliable resistance spot welds.
Force can vary because of variable factory air pressure, water in the air lines causing air cylinders to deteriorate and loss of air pressure due to worn seals.
This self contained instrument uses a cell with a force sensor to provide accurate digital read out for auditing weld electrode forces.
Accuracy of this instrument is better than 0.2% and can be switched to read 0-2000 kg, 0-20.00 kN or 0-4400lbs.
In cases of difficult access the head of the swivel head gauge can be swiveled at least ±72º up or down and rotates at least ±90º. Once the desired position is reached it can be fixed by a simple hand tightened knob. A 90 mm long handle is provided for optional use with 2 mountain positions either in-line or at 90º.
A support wrist strap is attached to the gauge so that in the event that it is forced out of the operators hand by misaligned electrodes, it need not fall to the floor and be damaged. |
|
Faults in welding tongs or incorrect process parameters in welding can result in production line waste or defective parts. Checking the electrode force periodically permits spark malfunctions to be detected at an early stage so that repairs can be carried out in good time.
The new Type 9833A test sensor allows precise and reliable measurements to be carried out with minimal electrode gaps. The built-in charge amplifier simplifies the task of mounting and helps to ensure the reliability required by the automobile industry.
|
|
Several Resistance Welding Accessories:
Welding Handpieces
Footpedals and Footswitches
Optics and Illumination Accessories
Electrode/Material Selection Guide
Electrode Force Gages
Electrodes
Unibond and Unitip Electrodes
Kovar Ribbon/Polishing Disks
Cables, Terminals, Connectors and Adapters
Electrode Holders and Adapters |
|
The Dytran model 1203V series is a ring style IEPE force sensor ideal for dynamic force applications such as press monitoring, automated machinery, and a myriad of other applications involving dynamic force measurements. The 1203V series is available in sensitivities from .5mV/Lb to 500mV/Lb with ranges from 100Lbs to 5,000Lbs. This sensor features very high stiffness, a no load mounted resonance frequency of 75kHz and excellent linearity characteristics. To learn more about the 1203V series, visit the Dytran website or email us.
Key Features
- Through hole mount
- .5mV/Lb to 500mV/Lb sensitivities
- Ranges from 100Lbs to 5,000Lbs
- Very high stiffness
- All st | | |
