|
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
Responding to specific projects is a part of our strength.
Are you looking for a solution for which no available component is to be found on the market? We will help you solving your problem by means of one of the special load cells we already realized or by developing a custom made model. Our design team will assist you in your project, from its very beginning till its complete realisation. Designing and realizing new solutions are our specialties; it belongs to our company's culture. During the last years, we have developed more than 1500 models and applications, from single part till medium and great serial production. We can present you a documented proposal including quotation within short time.
Even a part of an existing machine can, under certain conditions, become a force transducer measuring tension or compression. Transducers that will respond to your need at particularly competitive prices. |
|
SCAIME offers a wide range of load cells allowing to provide the best solution for all the weighing applications.
- Capacities from 1kg to 200t
- OIML R60 approval up to 6000d
- All modes of demounting of load:
Single point
Compression
Bending, shear beam
Traction
- Different materials and degrees from protection allowing to optimize the cost ratio/performance
- Complete range Certified ATEX
|
|
An extensive range of products for the use in the process industry, covering all accuracy levels, various automation needs and communication demands.
The applications range from level control by weight, flow by weight, bulk weighing of silos, standard batching, weighing and batching of agitated vessels and batching control in parallel including recipe handling in larger systems.
- High accuracy
- Superior installation properties
- Withstands up to 100% side load
- For hard environmental conditions (IP67)
- Covers most applications |
|
The LCIC-WIM allows to connect most load cells and scales to a PC via the popular USB or RS232/485 ports.
The LCIC-WIM was designed to fit all real-time weighing and force measurement applications, like:Checkweigher, Weighing In Motion (trucks and rails),Batching and filling systems, Testing machines etc. this product helps our customers to easily design their controllers saving them engineering time and money. |
|
| Weighing amplifiers and transmitters are available, for example, for networking platforms in control and automation systems. A choice of versions is supplied for the diverse hazardous area zone classifications and approvals. |
|
| Offering a wide choice for all the components of a weighing chain (load cells in capacities from 1kg to 200t, junction boxes, cables, analog or digital transmitters and zener barriers), SYSTEX is a comprehensive solution to ensure a complete compliance with the ATEX requirements for weighing applications in hazardous areas. |
|
Sensors of industrial weighing in shearing, entirely welded stainless and seals IP68.
Sensor 3510 is especially used for applications of weighing on hoppers, plates of weighing, and applications of measure of force.
Exist of 300 kg to 5000 kg with homologation IOLM in 3000 divisions |
|
Sensors of industrial weighing in inflection, entirely welded stainless and seals IP68.
Sensor 355 is especially used for applications of weighing on hoppers, plates of weighing, machines of conditionings and applications of measure of force. Exist of 5 kg to 250 kg with homologation IOLM in 3000 divisions
|
|
Sensor 220 stainless and entirely welded IP68 is used with the assembly "Mount Silo" for the weighing of silos and hoppers of strong capacities.
Exist of 5000 kg to 50.000 kg with homologation IOLM in 3000 divisions
|
|
Transmitter of entirely numerical weighing AST3-P with, out of standard:
Presentation: Assembly on rail DIN
Food: 24 Vcc + - 20%
Assembly: Rail DIN
Port serial: Addressable RS 485 with protocol MODBUS
Analogical exit: 0 - 10 V or 4 - 20 my isolated galvanically
Thresholds/relay: Two thresholds on adjustable relays 0 - 100%
Dimensions: 75 X 110 X 100 mm
Connections: On screw connector blocks likely to be stripped
Functions integrated multimeter & calibrator
Visualization & parameter setting via B.P. and indicator opposite front
Version WST3 is equipped with an additional port serial in PROFIBUS DP
|
|
Transmitter AST3 Is a transmitter of weighing for gauge sensors entirely numerical counsel ATEX II (1) GD for danger zone.
AST3 Is team out of standard of:
An analogical exit 16 bits - 4-20 my
An exit RS485 MODBUS RTU
Two exits skeletal relays
AST3 IS comprises functions integrated multimétries and calibration: visualization of the analogical value of exit; visualization of the signal mV/V of the sensors; generation of a signal 4-20 my.
Food 24 Vcc and assembly on rail DIN |
|
T010E is a weight transmitter amplifier that uses a modern microcontroller. Four push buttons and one display that shows the guide messages, help the operator in the configuration and weight calibration.
T010E is an instrument with high modularity. The base configuration is equipped with a display to show the weight data and two relays thresholds can be programmed as required. The options foresees one serial line available in RS232 or in RS485 mode, a radio transmission for remote data weight transfer (with R010E serial repeater), an analog output 0-10 V or an analog output 4-20 mA.
In the overload control modality (option) the instrument can be associated to category 1 as a security device (UNI EN 954-1 12-98 norm). The smaller dimensions, the best ratio quality price, make the T010E the best solution for many applications.
|
|
Utilising many years of load cell and transducer design and manufacturing experience, Flintec is able to provide a custom strain gaging service on customer supplied components. From low volumes through to serial production, Flintec can provide a cost effective and reliable service to OEMs.
For customers requiring solutions to force measurement problems, Flintec is able to supply custom designed and manufactured load cells, transducers, application parts and electronics or even complete sensing solutions.
|
|
FLINTEC load cells are designed to meet the most stringent
accuracy requirements. Certifications have been obtained
from Weights & Measures Authorities, worldwide. Single Point load cells are available in the capacities 6kg to 2000kg and include Accuracy Classifications GP,
C1, C3, C3 MI 7.5, C4 and C4 MI 7.5 according to OIML R 60;
Beside the aluminium Single Point Load cell Flintec offers total stainless steel construction and complete
hermetic sealing, making them suitable for use in the toughest industrial environments.
ATEX versions available. |
|
FLX
Bending Beam Load Cell
> 3000/6000d OIML
> 50/100/200 kg
FFX
Bending Beam Load Cell
> 3000/6000d OIML
> 300/600/1500/3500/5000 kg |
|
Flintec Electronics program offers a wide range of components for load cell and others strain gauge based sensors,
- Digital Junction Boxes
- Weighing Indicators
- A/D converters
- Analogue Amplifiers
- Remote display Terminals |
|
| ... products without technical information |
| |
|
|
see the results for the following category
