|
|
The HF25 Series controls address the challenges of microjoining. Miniature welds are highly sensitive to small heat profile fluctuations in the resistance welding process. Overheating deforms and destroys parts, while under heating results in a weak, unacceptable bond. To achieve consistent, reliable welds of small to microminiature parts, precisely controlled heating is required. This necessitates superior control of the energy output.
|
|
The HF27 High Frequency Inverter precisely controls and monitors electrical AND mechanical weld parameters. Miniature welds are highly sensitive to small heat profile fluctuations in the resistance welding process. Overheating deforms and destroys parts, while under heating results in a weak, unacceptable bond. To achieve consistent, reliable welds of small to micro miniature parts, precisely controlled heating is required. This necessitates superior control of the energy output.
CONTROL FEATURES:
Constant current, voltage, and power modes
Monitors energy and resistance
Force control
Monitor displacement and force
Max 2400A at 25kHz electrical feedback |
|
| The ISA range of Inverter power supplies provides the highest level of control available today in large scale resistance welding. The ISA-500AR, ISA-1000AR and ISA-2000AR are intelligently packaged in “NEMA” style enclosures and are designed to deliver robust performance in the harshest of production environments. The ISA models can deliver 500, 1000 and 2000 amps of primary welding current, respectively. |
|
Combine The Positive Timing Action of Gears With the Flexibility, Speed and Low Noise Level of Belts
The Browning HPT® Synchronous Belt Drive line offers a wide range of HP and speeds, from very low speeds - 10 RPM or less - to speed well over 5,000 RPM, with horsepower ratings from fractional to more than 200 HP.
Belt Drive Features and Benefits include:
Significantly Quieter Operation
New Parabolic Tooth Profile
Glass Fiber Cord Tension Member
Neoprene Rubber Body
Nylon Facing Fabric
Positive Drive, No Slip
Lower Belt Tensions
No Lubrication Required
Fully Interchangeable With Competitive Types
|
|
A Complete Selection Of BROWNING Products Leads To The Right V-Belt Drive For Every Application
The extensive BROWNING V-drive line means maximum economy, versatility and prompt availability for your every application - truly the right drive every time...for every service.
With the introduction of the revolutionary B5V Line, Browning brings up-to-the-minute technology to drive design, operation and inventory control. Now - more than ever - when you specify Browning, you select from the most extensive V-belt drive line in the world. New Combination Groove B5V - with 120 components covering 10-75 HP range. Mix and match with conventional A, B and 5V components
|
|
... see all the products in the category
Belts
|
FT-NAM-I-CFG (604 000)
• 6,2 mm. Housing width
• Namur sensor, dry contact inputs
• DIP switch configurable frequency ranges and output signal ranges
• 3 port 1500 VRMS isolation
• High precision conversion
• Wide operating temperature range
• Low power consumption
The FT-NAM-I-CFG configurable frequency transducer converts measured values of namur sensors and dry contacts into standard current and voltage signals or its inverse.
Input type, frequency ranges and output range are field configurable by means of easily accessible dip switches or can be specified when ordering. |
|
| Sluice Gate Drives to open and close sluice gates on canals and rivers. haacon is fabricating sluice gate drives from 1- 40 t load and there are different implementations. Lift and length of rack are individually adjusted to your requirements. Most of our models suit either manual operation as well as electric motor drive. For an individual offer please send the "Checklist for dimensioning a sluice gate drive" entirely refilled back to us. You can load it and further technical data from the haacon site. |
|
| ... products without technical information |
| |
| The Blancett Frequency-to-Current (F-to-I) and Frequency-to-Voltage (F-to-V) converters are microprocessor-based devices designed to provide an analog output directly from a Blancett turbine flow meter. The converters measure and calculate the flow rate of a turbine flow meter and produce an analog output representative of that flow rate, in the form of a 4-20 mA or 0-5 VDC signal. |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
... see all the products in the category
UPSs
|
FemtoPower1060-x-s are passively mode-locked 300 fs fibre lasers operating in the 1060 nm spectral range and delivering up to 5 W of average power.
The lasers consist of a master source, high power fibre amplifier and optical pulse compressor. The lasers are air-cooled, maintenance free and do not require any adjustments.
APPLICATIONS
Fundamental study
Micromachining
Bio-medical
Metrology |
|
Diesel engine control meets electric drive system!
HEINZMANN has combined its know how in Diesel Engine Control and in Electric Drive Systems by developing an electric motor/generator for diesel hybrid drives.
As a specialist in control systems for diesel engines, HEINZMANN is now able offer a major contribution to this forward-looking drive technology for the construction vehicle sector.
Description
Operation as a motor, generator or starter
- brushless
- Liquid cooling
Application
Applications for the HYPERION Hybrid Drive include
- wheeled loaders
- forklift trucks
- hydraulic excavators.
It is also possible to install the full-hybrid system in closed rooms, tunnels and aircraft hangers. |
|
The Cloupressor: BOGE SLF
A frequency controlled screw compressor. By changing the speed of both motor and air end the SLF can operate the air end in its specifically optimum range and adapt the compressed air output to the actual needs. Expensive idling times and motor switches are avoided. At the same time a smaller pressure band can be set, also helping to save enrgy.
Special benefit: By adjusting the air end speed by frequency regulation not only the FAD can be adjusted but also the pressure value! Usual frequency controlled screw compressors only change the FAD at a certain given maximum pressure. Lowering the pressure value did not result in a higher FAD. But with the SLF adjusting the pressure value will at the same time result in an adjustment of the maximum possible FAD! This way a 13 bar model easily can be switched to an 8 bar model including the higher volume flow of an 8 bar machine. There are no alterings or constructive changes necessary. All pressure values can be served with one machine.
New models up to 160 kW / 220 PS!
SLF 30 - SLF 221
Direct coupled & oil injection cooled.
Effective FAD: 1,06 - 28,21 m³/min
Pressure range: 8 - 13 bar
Drive rating: 22 - 160 kW
|
|
Ergo XJN/XSN
The sit-on stacker is one of the rider stackers. Gives ergonomic handling at a low cost.
Suitable for mixed handling, stacking/transfer with continuous driving time not exceeding 3 hours.
XJN (Junior) has the smallest turning radius.
XSN (Senior) has the biggest battery.
|
|
| Presto Pallet Stackers are ideal for servicing pallet racks. They are more economical and easier to use than conventional fork lifts. With over 40 models to choose from and a wide variety of available options, there's sure to be a Presto Pallet Stacker to meet your needs. |
|
|
|
see the results for the following category
