|
|
Hand driven all purpose gear drive for multiple applications. Motor drive possible for a speed
up to 100 revolutions/min.
— robust and reliable
— maintenance-free
— security crank with internal self actuating load brake
— alternatively without self actuating load brake for shifting of loads
can be equipped with:
— one or several rope drums
— chain wheels for roller chains
— chain sprockets for link chains
— with crank extensions
— with crankshaft extension
|
|
Spurgear winches TL125-2000kg
The GEBUWINch range of hand-driven spur geared winches are robustly built and meet the construction and safety standards in accordance with DIN 15020. The spur geared winches are available in various hoisting capacities. These are between 125 kg and 2000 kg calculated on the first cable layer on the cable drum. The spur geared winches are equipped with a load pressure brake. This brake holds the load at any required height during hoisting and lowering. The cranks can be adjusted in length and are recoil-free. All rotating parts run in maintenance-free bearings. The winches are available in combined grey/black enamel paint (GR) or provided with zinc-plated surface treatment (EV), which means that rust protection is further improved.
The type designation is as follows:
TL = range of GEBUWINch spur geared winches for hoisting load 125, 300, 500, 1000 or 2000 kg
GR= Painted grey colour
EV= zinc-plated |
|
Wormgear winches WW2000-5000kg
The GEBUWINch range of hand-driven worm geared winches are robustly built and meet the construction and safety standards in accordance with DIN 15020. The worm geared winches are available in different hoisting capacities. These are between 2000 kg and 5000 kg calculated on the first layer on the cable drum. The worm geared winches are equipped with a load pressure brake. This brake holds the load at any required height during hoisting and lowering. The cranks can be adjusted in length and are recoil-free. All rotating parts run in maintenance-free bearings.
The winches are available in combined grey/black enamel paint (GR) or provided with zinc- plated surface treatment (EV), which means that rust protection is further improved.
This range of winches is standard provided with a secondary drive. This allows you to use a second hoisting speed by transferring the crank.
The cable drum can be provided with a cable groove (GD) for better cable routing and storage.
The winches are available with a free-spool device for the cable drum (FS). This cable drum free-spool device can, if necessary, also be provided with an adjustable friction brake (FSB), for controlled cable unwinding.
The type designation is as follows:
WW = range of GEBUWINch worm geared winches for hoisting load 2000, 3000, 4000 or 5000 kg
GR= painted grey colour
EV= zinc-plated
D= 1 cable compartment
2D= 2 cable compartments
GD= grooved cable drum
FS= provided with cable drum free-spool device
FSB= provided with cable drum free-spool device and adjustable friction brake for controlled cable unwinding |
|
Wormgear winches VL250-1500kg
The GEBUWINch range of hand-driven worm geared winches are robustly built and meet the construction and safety standards in accordance with DIN 15020. The worm geared winches are available in different hoisting capacities. These are between 250 kg and 1500 kg calculated on the first cable layer on the cable drum. The worm geared winches are equipped with a load pressure brake. This brake holds the load at any required height during hoisting and lowering. The cranks can be adjusted in length and are recoil-free. All rotating parts run in maintenance-free bearings.
The winches are available in combined grey/black enamel paint (GR) or provided with zinc-plated surface treatment (EV), which means that rust protection is further improved.
The cable drum can be provided with a cable groove (GD) for better cable routing and storage.
By dividing the cable drum into a number of cable compartments, the use of 2 cables (D or 2D) as standard is possible on all worm geared winches. Upon request, a number of cables is possible.
The type designation is as follows:
VL = range of GEBUWINch worm geared winches for hoisting load 250, 500, 1000 or 1500 kg
GR= painted grey colour
EV= zinc-plated
D= 1 cable compartment
2D= 2 cable compartments
GD= grooved cable drum |
|
Upon request, all worm geared winches can be equipped with an air motor drive.
The standard winches then need to be modified.
The air motor is easy to uncouple to allow a number of winches to be operated by 1 air motor. |
|
| ... products without technical information |
| |
... see all the products in the category
Winches
|
| Clampco worm drive hose clamps are manufactured with 300 series stainless steel bands and housings. Customers may choose between zinc plated or all stainless screws. The hose clamps are available in standard SAE sizes. Micro series hose clamps are also available. The worm drive clamps are used on all types of commercial and industrial hose and duct applications. |
|
| ... products without technical information |
| |
| Rack & pinion jacks load 1,5 t to 10 t (fig.) withself-locking security crank, keeps the charge in every required position - for pulling or pushings. Special versions on request: - different length of rack - different lift - drive shaft to connect several jacks - with internal brake and removable crank |
|
Rack & pinion jacks load 0,5 t and 1 t, with self-locking worm gear for lifting, for lowering, adjusting and fixing of mechanical components, devices, machines, etc.. 0,5 t version also available in stainless steel
robust version with milled rack and hardened driving parts, for in- and outdoor applications
Special versions against additional charge:
- an other lift or length
- an other crank version
- an other fixing possibility
- an other surface treatment
|
|
S 2000 Plus
- Upto 15 % more lift at optimized construction height
- Best power to weight ratio
- Unrivalled corrosion resistance through zinc phosphate and powder coating
- Slightly operating sturdy gear, comfortable to handle
- Reinforced Compensating Foot - the optimal solution for trailers with pneumatic suspensions (130 mm compensation)
- Modular system for OE and replacement market; 5 types of feet interchangeable
- Enormous buckling strength through full length welded back plate, ideal to accept auxiliary equipment, such as holder for brake shoe or fire distinguisher
|
|
Joyce/Dayton - Established 1873
Joyce Bevel Gear screw jacks offer higher efficiency and greater speed than other mechanical screw jacks. At the same time, Bevel Gear S Series jacks still provide the benefit of a self-locking screw-no special brake is required to prevent the jack from lowering under load. Spiral bevel gears increase strength for higher capacities.
Bevel Gear screw jacks also act as a miter gear box, making them an ideal choice for many multi-jack systems. As many as three output shafts may be specified for mounting motors, limit switches, readout devices and other accessories.
Bevel Gear screw jacks are also available complete with reducer or direct drive in a ready-to-run package.
Joyce bevel gear jacks come in translating screw (shown) and rotating screw (keyed for traveling nut) designs. Jacks are available with one of four standard screw ends or special ends to meet your requirements.
|
|
Gear Shaving Cutters. Gleason manufactures
and resharpens precision shaving cutters to
support Gleason Hurth shaving machines and
any other gear shaving machines. The
Gleason shaving cutter design is optimized
for maximum tool life. |
|
Chamfering Rolling Deburring Tools
Chamfering tools: for spur or helical gears, for straight or inclined gear lateral surfaces
Deburring tools:
- P type (standard tool for straight gear lateral surfaces)
- P 1000 type (like P type but grooved)
- PR type (with alternate sections for straight gear lateral surfaces radiused to the root)
- PR 1000 type (grooved tool for straight gear lateral surfaces radiused to the root)
- A 1000 type (grooved tool for inclined gear lateral surfaces)
- AR 1000 type (same as A 1000 type but radiused to the root)
- SPR 1000 type (special tool for chain sprockets)
- T 1000 (grooved tool for chamfering turning chamfers on the tooth tip)
Chamfer-roller tools: to machine the gear tooth profile, to remove the secondary burr
|
|
As one of the largest manufacturers of gear cutting tools worldwide, our tool manufacturing programme features a wide range of shaper cutters, branded Samputensili, Fellows and Star SU, including disk-type shaper cutters, deep counterbore-type shaper cutters and shank-type shaper cutters. Our shaper cutters are generally ground for pre-finishing and finishing operations, although in certain cases they may also be supplied unground.
Min. / Max. module: 0,5 - 8,0 mm
Max. diameter: 300 mm
Profile modifications: tooth tip chamfer, protuberance, topping, flank modifications for tip and/or root relief on gear, modification of pressure angle, combinations of several of the above modifications.
Materials: various high-speed steels produced by powder metallurgy. Other materials are available on request.
Special profiles / profile modifications for chain sprockets, cams, splines, timing belts and large modules.
Our Express programme features X4®shaper cutters. We not only guarantee supply of your shaper cutters including coating in just 4 weeks (20 working days), but, in comparison with conventional shaper cutters, our X4® tools also offer you significant cost saving advantages, since the shorter usable profile reduces both production costs and delivery times. Moreover, advanced manufacturing techniques have improved the quality of our X4® shaper cutters. We can supply class AA tools to DIN 1829 standards and even AAA tools in terms of certain parameters such a pitch and profile, and we also guarantee DIN AA quality throughout the entire life of your tool. When it comes to small batch or prototype manufacturing, these tools make for great savings in terms of production costs.
|
|
| Rocking type inspection instruments for gears and splines are a cost-efficient solution for single productions and small batches. With a bit of skill, the actual dimension over and between balls, i.e. the highest measurement point, can be found by rocking the instrument. We recommend a Frenco UPM-certificate for all VA inspection instruments in order to verify a sufficiently small measuring uncertainty regarding the tolerance to be measured. |
|
| ... products without technical information |
| |
Internal and face grinding machines for gear grinding applications.
Internal grinding length 190 mm
Internal grinding diameter 200 mm
Workpiece weight 80/170 kg |
|
| ... products without technical information |
| |
The KEM Deburring Machine has been developed in WERA
technical center and it is now built under license by FIMAT.
It has been designed for deburring and chamfering special and bevel gears.
The machine concept is optimized for short serials and a wide
variety of work parts. The tool features 5 degrees of liberty and
is able to perform any work part profile with extreme precision
and speed. It also suits other complex work part shapes requiring
precise and sharp chamfering.
DESIGN FEATURES
* Compact machine.
* Working area completely guarded.
* Bedplate allowing quick & easy shaving discharge.
* Loading area suitable for access with tackle.
* High milling speed leaves out any secondary burrs.
* Continuous speed adjustment.
* No axis with manual adjustment.
* Use of standard and special tools. |
|
The KEM Deburring Machine has been developed in WERA
technical center and it is now built under license by FIMAT.
It has been designed for deburring and chamfering special and bevel gears.
The machine concept is optimized for short serials and a wide
variety of work parts. The tool features 5 degrees of liberty and
is able to perform any work part profile with extreme precision
and speed. It also suits other complex work part shapes requiring
precise and sharp chamfering.
DESIGN FEATURES
* Compact machine.
* Working area completely guarded.
* Bedplate allowing quick & easy shaving discharge.
* Loading area suitable for access with tackle.
* High milling speed leaves out any secondary burrs.
* Continuous speed adjustment.
* No axis with manual adjustment.
* Use of standard and special tools. |
|
| Gleason-Hurth ZEA 4 Rotary Deburring Machine is designed for the dry-deburring of disc-type workpieces of up to 280 mm and shafts with 400 mm length. The funnel shaped machining area ensures ideal chip disposal. Advantages of dry deburring include the deletion of workpiece dry cleaning and health hazards due to oil addition, excellent environmental conditions, simple and easy chip disposal and cost savings without oil. Machine is also available for wet processing. |
|
Geared Rotary Limit Switches
Geared Rotary Limit Switches are worm and gear-reduction limit switches that provide limit control on rotating-drive equipment. (CR115E Series) |
|
|
|
see the results for the following category