|
|
ARF20 / ARF30 - Logical and analogical status transfer 433/434MHz or 869MHz – 10 & 500mW LICENCE-FREE
* Monodirectional transmission of 8 logical status or 4 analogical values up to 4km
* 8 TOR inputs toward 8 "open collector" outputs or 4 relays
* 4 channels/8 bits – voltages 0/5V or currents 0/20mA
* Complies with the European standard RTTE EN300-220 / EN301-489
* IP65 box ready for use
* Industrial applications, long range transmissions and/or in disturbed environments
(in-town network, agriculture, difficult environments, building interconnection…)
o Information transfer
o Wireless remote control
o Alarm and security system triggering
o Level control…
|
|
Zlinx Wireless I/O, point-to-point/multi-point
How to select the right wireless system for your Modbus point-to-point/multi-point applications
Simplify your installation by sending your digital and analog inputs and outputs over the air. Why run a wire when you can install a Zlinx wireless module to replace it? The new Zlinx wireless product line provides point-to-point or multi-point communication, replacing your wires.
With bi-directional flow control, the controllers allow full-duplex transmissions to optimize the communiation efficiency. Modbus Mode - Up to 150 base modules in a system. Up to 6 systems can run simultaneously by using difference RF network I/O.
Connects directly to analog, digital and temperature inputs and outputs
Point to point/multi-point wire replecement
Expandable, modular design
Modbus compatible
|
|
|
|
|
|
|
The TempTrackr™ Multipoint System provides a batteryless, non-invasive and low cost temperature measurement solution that is ideally suited for applications ranging from High Power Switches to Rotating Machine Components. The Starter Kit is designed to showcase the capabilities of the TempTrackr™ Multipoint System. Each Kit includes three batteryless wireless temperature sensors that are capable of reading temperatures between 0°C and 120°C. The three sensors provide the ability to monitor temperature at multiple points of interest. The Surface Acoustic Wave (SAW) resonator within each sensor is powered by bursts of electromagnetic radiation emitted by a wireless reader (also known as a wireless interrogation unit). A feedback signal, conditioned by the temperature to which the resonator is exposed, is then electromagnetically transmitted to the wireless reader where it is processed for temperature measurement. The TempTrackr™ Multipoint System is capable of tracking up to six sensors and can provide temperature data via the CAN communication protocol. The number of sensors can be extended to 12 by making use of multiple interrogation antennae. The Starter Kit is an ideal technology evaluation tool3. SenGenuity will work closely with you to adapt the TempTrackr™ Multipoint System to meet the specific needs and requirements of your application.
|
|
|
|
|
|
Wireless Remote I/O - Cable Replacement
Banner introduced a new product line called SureCross Wireless I/O.
The DX70 is point to point architecture based on a pair of emitter/receiver. Digital or analogue I/Os are directly linked based on the internal terminal chamber identification. Unlimited pairs can work together in the same area without any interference.
The DX80 is a point to multipoint with up to 56 Nodes linked to one Gateway. The possible high number of I/Os can be transferred to supervision by communication with Modbus RTU (RS485), EtherNet/IP or Modbus TCP. Some Nodes can be powered by 24 Vdc, battery box or solar panel with rechargeable battery. Special DX99 Nodes come with ATEX certification Zone 0 for gas.
The DataRadio DX80DR2M is used mainly for serial (RS232 or RS485) cable replacement. This can be configured with one master and numerous slaves.
SureCross products fit with many different types of Industries (Factory and Process Automation, Water Treatment...). The high performance, reliability and low cost of this product makes it a natural solution for renovation/revamping of existing installations.
Main features include:
Rugged industrial housing giving an IP67 rating
Reliable and secure data communication with FHSS
Accept up to 12 different analogue or digital signals on one module
Up to 56 Nodes per Gateway with extended address mode
Line of sight maximum distance of 3 Km between Node and Gateway
Built-in signal strength visualisation
Link loss output indicates communication status
Specific FlexSensors adapted for a longer lifetime when using a battery
Frequency band of 2,4 GHz and 900 MHz depending on country
|
|
|
TO-PASS, a complete telecontrol solution offered by WAGO consisting of stand-alone fault detectors with GSM connection, optional IP66 protection and a telecontrol PLC that can be linked to the WAGO-I/O-SYSTEM. This enables widely branched systems to be acquired in the same manner as remote stations. A GPS version is even available for locating vehicles using satellite signals. An Internet server with MySQL database rounds out the system features.
|
|
|
SATELLINK products makes constructing your wireless communication applications easier than ever. The first product in the SATELLINK line, SATEL I-LINK 100, is designed for transparent transfer of contact information or analogue signals from one location to another together with the SATELLINE radio modems.
|
|
|
Wireless I/Os are the solution for applications where cables are not suitable to be used, such as cranes, AGVs and robots. In those cases wireless I/Os are used to transfer status and control information.
|
|
Wireless-based high-precision, 8-channel temperature measurement module;
requires WLS-IFC wireless gateway device
- 8 temperature input channels
- Supports thermocouples, RTDs, thermistors, and semiconductor temperature devices
- Superior performance - accuracy exceeds sensor output
- 8 digital I/O bits; user-configurable for alarming
- 802.15.4 wireless protocol
- Range: Up to 150 feet indoors, 2400 feet outdoors
- Included Software: TracerDAQ™, Universal Library, Universal Library for LabVIEW, and InstaCal
- Lifetime Warranty & Harsh Environment Warranty® included
|
|
The Radio Printer is part of a wireless system for temperature monitoring and control. It is made up by one or more temperature sensor-transmitters, like the TempStick Radio, and a radio receiver, the Radio Printer itself. It has everything it needs to work and doesn't require any PC or software : the display allows to configure the acquisitions and the printer to store easily and quickly all the stored data.
- no need of a PC nor software;
- graphic and alphanumerical LCD display;
- LED and sound alarms for thresholds set by the operator;
- display values for each sensor and all data recorded;
- rechargeable batteries and external power supply.
Applications:
stock houses and warehouses monitoring;
fridges and fridge cells monitoring;
environment monitoring;
computer rooms control;
laboratories monitoring;
transport monitoring;
catering services;
HACCP compliance temperature monitoring;
ISO compliance temperature monitoring.
|
|
| ... products without technical information |
| |
|
|
