|
|
PERFORMANCE
Power Output: 500mW@5V(Default), 1W@9V(customized)
RF Line-of-sight Range: 4000m@1200bps, 2000m@9600bps
RF Effective Rate: 1200/2400/4800/9600/19200/38400bps optional Receiver Sensitivity: -124dBm@1200bps, -118 dBm@9600bps
Supply Voltage: +4.75~5.5VDC
Transmit Current: <400mA@500mW, <500mA@1W
Receive Current: <40mA
Sleep Current: <5µA optional ex-factory
Frequency Band: 433MHz(Default)
400MHz~470MHz(customized)
Channel: 8(Default), 16/32 (customized)
Default Interface: COM1:TTL/UART,COM2:Non-Standard RS232 or RS485
Size: 53mm×38mm×10mm
Weight: 34g
Antenna Base: 50Ω
Operating Temperature: Industrial: -35℃~+80℃(TCXO crystal)
Commercial: -20℃~+60℃
Frequency Stability ±2.5ppm Industrial
±10ppm Commercial |
|
25kHz UHF Narrow Band FM Multi Channel Transmitter and Receiver.
The TLC2H transmitter and RLC2H receiver offer a low power, reliable data link in an industry standard pin out and foot print.
This makes the TLC2H/RLC2H pair ideally suited to those low power applications where existing wideband modules have insufficient range, or where low cost multi-channel operation is needed without compromising on RF specification or regulatory requirement.
|
|
Power Output:10~20mW. Single transmitter
RF Line-of-sight Range:≥800m
RF Effective Rate: 1200bps(Default),4800bps(customized)
Supply Voltage: 3.1~5V
Transmit Current: <45mA
Sleep current: <20µA
Frequency Band: 430.675MHz(Default)430~435MHz(customized)
Channel: Single Channel
Bandwidth: 10kHz
Interface: TTL(Default), download/setup
Size: 47mm*26mm*8mm
Antenna: 50Ω, with HAC-TH433 Spring Antenna
Weight: 22g
Operating Temperature:
-20℃~+60℃ 430.675MHz
-0℃~+60℃ 430.375MHz
Frequency stabilization:
±5PPM |
|
opens and closes doors and gates
low energy consumption and radio emission
actuation by pull-wire
also for outside applications,sensing range 300 m
sensing range inside 30 m |
|
| Wireless interface products provide a cost effective alternative to expensive hard wired connections. The wireless product provides continuous, 24/7 communication using the FCC licenses free 900MHz frequency. Using Frequency Hopping Spread Spectrum (FHSS) technology, a robust signal is provided that is virtually free from disruption due to interference. This technology has been proven in thousands of installations worldwide. |
|
Wireless I/O solutions from Phoenix Contact offer flexible and reliable data transmission for your applications. Monitoring and controlling your processes is reliable with point to point, and multipoint to point industrial radios.
These industrial radios can be incorporated into controlling pump stations, monitoring tank levels and sensors as well as a variety of additional industrial applications. |
|
| ... products without technical information |
| |
The LCIC-WIM allows to connect most load cells and scales to a PC via the popular USB or RS232/485 ports.
The LCIC-WIM was designed to fit all real-time weighing and force measurement applications, like:Checkweigher, Weighing In Motion (trucks and rails),Batching and filling systems, Testing machines etc. this product helps our customers to easily design their controllers saving them engineering time and money. |
|
| Weighing amplifiers and transmitters are available, for example, for networking platforms in control and automation systems. A choice of versions is supplied for the diverse hazardous area zone classifications and approvals. |
|
| Offering a wide choice for all the components of a weighing chain (load cells in capacities from 1kg to 200t, junction boxes, cables, analog or digital transmitters and zener barriers), SYSTEX is a comprehensive solution to ensure a complete compliance with the ATEX requirements for weighing applications in hazardous areas. |
|
Transmitter of entirely numerical weighing AST3-P with, out of standard:
Presentation: Assembly on rail DIN
Food: 24 Vcc + - 20%
Assembly: Rail DIN
Port serial: Addressable RS 485 with protocol MODBUS
Analogical exit: 0 - 10 V or 4 - 20 my isolated galvanically
Thresholds/relay: Two thresholds on adjustable relays 0 - 100%
Dimensions: 75 X 110 X 100 mm
Connections: On screw connector blocks likely to be stripped
Functions integrated multimeter & calibrator
Visualization & parameter setting via B.P. and indicator opposite front
Version WST3 is equipped with an additional port serial in PROFIBUS DP
|
|
Transmitter AST3 Is a transmitter of weighing for gauge sensors entirely numerical counsel ATEX II (1) GD for danger zone.
AST3 Is team out of standard of:
An analogical exit 16 bits - 4-20 my
An exit RS485 MODBUS RTU
Two exits skeletal relays
AST3 IS comprises functions integrated multimétries and calibration: visualization of the analogical value of exit; visualization of the signal mV/V of the sensors; generation of a signal 4-20 my.
Food 24 Vcc and assembly on rail DIN |
|
T010E is a weight transmitter amplifier that uses a modern microcontroller. Four push buttons and one display that shows the guide messages, help the operator in the configuration and weight calibration.
T010E is an instrument with high modularity. The base configuration is equipped with a display to show the weight data and two relays thresholds can be programmed as required. The options foresees one serial line available in RS232 or in RS485 mode, a radio transmission for remote data weight transfer (with R010E serial repeater), an analog output 0-10 V or an analog output 4-20 mA.
In the overload control modality (option) the instrument can be associated to category 1 as a security device (UNI EN 954-1 12-98 norm). The smaller dimensions, the best ratio quality price, make the T010E the best solution for many applications.
|
|
Flintec Electronics program offers a wide range of components for load cell and others strain gauge based sensors,
- Digital Junction Boxes
- Weighing Indicators
- A/D converters
- Analogue Amplifiers
- Remote display Terminals |
|
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
Features:
From 2.5 to 1250 kN (0.28 to 140 tons)
Admissible overload: 150% of the nominal load
Overload at rupture: 350% to 700% of nominal load (according to the model)
Pin made of high resistance stainless steel.
Insensitive to external mechanical and chemical effects (strain gauges inside the pin)
Ideal for use in hostile environments
Rugged and tight construction; maintenance-free
For new or refitted installations
ISO 9001 Certified
|
|
SENSY is one of the most experimented companies in the load limitation for hoisting devices business, because of its 20 years experience in this field of activity. This is why we offer one of the largest product range on the market with strain gauge technology load cells and load pins, electronic load limiters and displays and also dynamometric shackles and wedge sockets.
When it goes about setting in conformity a hoisting equipment, you think about load limitation equipment for production or expedition department overhead cranes (EOT), harbour cranes,
We talk then about heavy loads, Crane classification (FEM) and big investments. Men think that hoisting devices for smaller capacities do not deserve such investment. Therefore, we have developed a range of load cells and electronic load limiters for lower capacities hoisting equipments. We talk about load cells with fast and easy implementation combined with load limitation electronic with 1 or 3 set points. A cost effective solution for equipping your low and medium capacity overhead crane. |
|
| ... products without technical information |
| |
|
|
see the results for the following category
