|
|
six lines multi boring machine
Technical Parameter MBZ266
Max drill diameter 35mm
Max working depth 60mm
Length between vertical spindle heads 130-3250mm
Numbers of spindle 21*2+11*8lines
Spindle running speed 2840r/min
Motor power 1.5kw*6
Air pressure 6-8kg/cm2
Overall size 4600*2500*1600mm
|
|
| ... products without technical information |
| |
|
The highly polished open flute not only allows for easier chip formation and evacuation, but also provides for a sharper cutting edge that delivers a better edge finish on a variety of materials. Our premium micro grain carbide allows for superb wear resistance and tool strength. Special point geometry contributes to improved bottom finish and plunging capabilities. Tools are available in upcut and downcut versions from 1/16" through 3/8" diameters.
|
|
Onsrud is proud to announce the launch of our NEW taper tools. These cutters are made of premium micro-grain carbide and are available in a variety of sizes, lengths, and angles.
The tools are available with a ball nose tip giving them the flexibility to cut draft angles in molds to 3D decorative profiles. The cutting geometry will allow them to cut a variety of materials and produce a good edge finish.
Custom tools can be made upon request.
Material: Wood, Plastic, Aluminum
|
|
Modular high-performance CNC-turn-mill-centers
The UniCen is a turning and milling center with integrated B-axis where all requirements for complete machining have already been implemented: turning, milling, drilling and thread-cutting all on one machine. The workpiece is loaded on one machine only and can then be finished completely. With up to five interpolating axes even complex free form faces can be machined.
|
|
|
|
|
|
The Unicom 6000 machining centre is ideally suited for vertical turning and multi-sided machining of complex components. This highly flexible and powerful machining centre for complete machining results from the continuous development of vertical machining centres over a period of more than 25 years.
The concept of Unicom 6000 is based on a moving table with integrated carousel turning station and an interface that can receive pallets of up to 2.500 mm in diameter. The table movement is designated as Y-axis and it runs underneath a traverse with cross slide and spindle carrier. The movements of cross slide and spindle carrier are designated as X-and Z-axis respectively.
Unicom 6000:
4-Axes complete machining centre with HSK100-A interface, carousel turning station and pallet changer. The machine can be equipped with a right angular head or a universal head, in combination with C-axis mode in the carousel turning station.
Unicom 6000-HV:
5-Axes complete machining centre with carousel turning station, pallet changer and HSK 63-A interface in the integrated Unisign Nutator NC machining head as 5th axis, in combination with C-axis mode in the carousel turning station. This configuration is capable of 5-axes machining of complex components.
|
|
Highly productive milling-turning centers with one (MT) or two (MT-TWIN) milling spindles and one or two turning spindle(s) for complete machining of semi-finished products and saw sections.
Maximum workpiece quality by complete machining on one machining center. Workpiece clamping is done by means of clamping chuck or device.
The MT-S is designed for highest flexibility and ideal for small batches. The MT and MT-TWIN series offer maximum productivity for medium and large batches.
Reduction of costs per part by up to 30 % thanks to TWIN technology and 5-axes complete machining.
|
|
|
|
|
|
The Leonard machines are a complete and modular range of Horizontal Lathes for the machining on medium to large work pieces with highest performances in terms of rigidity for rough operations and precision for finishing operations. The main feature of these machines is the technology of the preloaded Hydrostatic ways which are successfully used for both cross and longitudinal slides.
Other machining operations can be performed with the Leonard system, like Boring, Milling or Drilling operations. The different working units can be Combined on a column with rotating base ("B" Axis) or on different Pallets to be manually or automatically installed in the carriage.
The Leonard lathe can be supplied with different type of Steady rests according to the work piece and the required machining.On demand different accessories are available like the work piece probe, the tool probe and the Automatic tool changer.
Safop has developed some special system for the measuring of high sophisticated work pieces like the turbine rotors. The Run Out Measurement System and Blade Measurement System are used with success by the main producers of this type of work pieces.
|
|
Drilling
Machining with coolant supply through the tool, regardless if the tool is in radial, axial or in an inclined position. Accuracy-killing changes between various machines is avoided.
Thanks to very high feed forces and high power also at low speed drills with large diameter can be used with optimum performance. A single look into the speed-power-diagram or the speed-torque-diagram shows the difference...
|
|
| ... products without technical information |
| |
Modular high-performance CNC-turn-mill-centers
The UniCen is a turning and milling center with integrated B-axis where all requirements for complete machining have already been implemented: turning, milling, drilling and thread-cutting all on one machine. The workpiece is loaded on one machine only and can then be finished completely. With up to five interpolating axes even complex free form faces can be machined.
|
|
|
|
|
|
The Unicom 6000 machining centre is ideally suited for vertical turning and multi-sided machining of complex components. This highly flexible and powerful machining centre for complete machining results from the continuous development of vertical machining centres over a period of more than 25 years.
The concept of Unicom 6000 is based on a moving table with integrated carousel turning station and an interface that can receive pallets of up to 2.500 mm in diameter. The table movement is designated as Y-axis and it runs underneath a traverse with cross slide and spindle carrier. The movements of cross slide and spindle carrier are designated as X-and Z-axis respectively.
Unicom 6000:
4-Axes complete machining centre with HSK100-A interface, carousel turning station and pallet changer. The machine can be equipped with a right angular head or a universal head, in combination with C-axis mode in the carousel turning station.
Unicom 6000-HV:
5-Axes complete machining centre with carousel turning station, pallet changer and HSK 63-A interface in the integrated Unisign Nutator NC machining head as 5th axis, in combination with C-axis mode in the carousel turning station. This configuration is capable of 5-axes machining of complex components.
|
|
Highly productive milling-turning centers with one (MT) or two (MT-TWIN) milling spindles and one or two turning spindle(s) for complete machining of semi-finished products and saw sections.
Maximum workpiece quality by complete machining on one machining center. Workpiece clamping is done by means of clamping chuck or device.
The MT-S is designed for highest flexibility and ideal for small batches. The MT and MT-TWIN series offer maximum productivity for medium and large batches.
Reduction of costs per part by up to 30 % thanks to TWIN technology and 5-axes complete machining.
|
|
|
|
|
|
The Leonard machines are a complete and modular range of Horizontal Lathes for the machining on medium to large work pieces with highest performances in terms of rigidity for rough operations and precision for finishing operations. The main feature of these machines is the technology of the preloaded Hydrostatic ways which are successfully used for both cross and longitudinal slides.
Other machining operations can be performed with the Leonard system, like Boring, Milling or Drilling operations. The different working units can be Combined on a column with rotating base ("B" Axis) or on different Pallets to be manually or automatically installed in the carriage.
The Leonard lathe can be supplied with different type of Steady rests according to the work piece and the required machining.On demand different accessories are available like the work piece probe, the tool probe and the Automatic tool changer.
Safop has developed some special system for the measuring of high sophisticated work pieces like the turbine rotors. The Run Out Measurement System and Blade Measurement System are used with success by the main producers of this type of work pieces.
|
|
Drilling
Machining with coolant supply through the tool, regardless if the tool is in radial, axial or in an inclined position. Accuracy-killing changes between various machines is avoided.
Thanks to very high feed forces and high power also at low speed drills with large diameter can be used with optimum performance. A single look into the speed-power-diagram or the speed-torque-diagram shows the difference...
|
|
| ... products without technical information |
| |
SERCO PORTABLE MACHINING UNITS
The SERCO units are positioned and locked by means of a column/arm system clamped on the outer part of the surface to be machined (allowing internal machining). Machine set up is fast and easy. After a first visual positioning, we can get within a few minutes, using a simple specific device, a parallelism and concentricity within a 1/100 of mm precision. A powerful air motor drives the tool rotation (hydraulic motors on request) and radial automatic feed (with a selection of two speeds).
Maintenance
Flanges
Safety valves
Sealing valves
High pressure valves
Portable Equipment
Portable machining equipment
Portable boring and surfacing machines
Portable surfacing machines
Portable grinding machines
Portable lapping machines
For further information please contact :
PROTEM SAS
ZI LES BOSSES
F-26800 ETOILE SUR RHONE
FRANCE
Tel +33 4 75574141
email : n.reicher@protem.fr
|
|
The V-Lap F6 is standard equipped with a range of grinding and centre plates for grinding and lapping any type and size of ‘flat’ seat up to 6” / DN150 mm. The centre plate keeps the grinding plate in position, but also gives an eccentric rotation ensuring constant and complete coverage and absolute flatness.
Abrasives
The V-Lap F6 is completed with a large consumer quantity of polyester based, self-adhesive Aluminum Oxide round foil tips in grains rough, middle and fine. The foil tips can be used dry and on all common seat materials.
Drive machine
The V-Lap F6 is standard equipped with a battery drive machine and is delivered with 2 battery’s. The low weight and good balance of the machine increases the grinding performance and makes it easier to attain high quality flat ‘results’.
The complete set is packed in a robust, but light weight carrying case.
|
|
3 Axis 800 / 2000 / 4000
The machine is equipped with: one control panel, with an auto diagnostic display system, for the rotation and the feed of the arm and the milling cutter.
|
|
|
WIRTH supplies a large range of shaft boring machines and drill rigs using different technologies, for the excavation of vertical shafts.
|
|
|
|