|
|
Flip Mirror Holder KSH 90
The swing leaf bears a wobble plate with an adjustment range of ± 0.5° and an aperture of 2". Optics with a thickness > 12 mm (normally 2" mirrors) are fixed with a plastic screw.
Optical components (such as mirrors and beam splitting paltes) having a thickness of only 10 mm can be pressed aganst three stops with the enclosed two clamping shoes and thus fixed.
The swing angle is 45°, the repeatability < 100 µrad. The swing time of the motorized version is about 1 s.
- for use with SYS 90
- black anodized aluminium alloy
- mountable onto pin or slide
- manual operation or motorized
|
|
|
This kinematic mount is designed for ultrathin nonlinear crystal positioning. The mount accepts ring holders of Ø25.4 mm and thickness up to 10.5 mm. The housing is stopped by a rest-flange inside the central aperture of the platform, and is secured by a threaded retaining ring.
|
|
The Laser Mech Lens Mounting System solves the problem of lens removal for replacement and inspection. By using a simple cartridge mounted lens inserted into a side slot in a permanently positioned manifold block, the problems of the traditional threaded, axially inserted lenses are avoided. This innovative mounting method allows removal and replacement of the lens in seconds with no readjustment of the optical alignment and without the removal, replacement or disassembly of any other part of the optical system.
Each assembly consists of a lens mount manifold block with very fine, adjustable lens centering screws and a spring-loaded, lens holder assembly to hold the lens. The lens holder contains all the seals necessary to pressurize the space beneath the lens for use with the Gas Jet Manifold.
|
|
|
ROLYN Mirror Mounts are designed to give the very best combination of economy and performance. There is no glass-to-glass contact. Clear aperture obscuration caused by the plastic mirror holders is minimal. These three holders form an adjustable rigid orthogonal kinematic mount for the mirror which resists vibration and handling. Black anodizing minimizes reflections. Mirrors are not supplied with the mount.
|
|
As you scan through our various mounts we have a selection of Single Circular Filter Wheel Mounts, a Universal Stand Mount, Compensated Circular Filter Mounts & a 8 Position Filter Mount.
* Compensated Linear Filter Mounts
* Degree Scales
* Mounts
* Storage Boxes
|
|
|
The Universal Mirror Mount/Platform 840-0052 is suited for precise adjustment of standard mirrors which can be directly bound to it. The mount may be used in horizontal position as a tilt table. Then it can be used to align opto-mechanics around two axes. For such mounting the mount has an M4 hole on its back
|
|
The Laser Mech Lens Mounting System solves the problem of lens removal for replacement and inspection. By using a simple cartridge mounted lens inserted into a side slot in a permanently positioned manifold block, the problems of the traditional threaded, axially inserted lenses are avoided. This innovative mounting method allows removal and replacement of the lens in seconds with no readjustment of the optical alignment and without the removal, replacement or disassembly of any other part of the optical system.
Each assembly consists of a lens mount manifold block with very fine, adjustable lens centering screws and a spring-loaded, lens holder assembly to hold the lens. The lens holder contains all the seals necessary to pressurize the space beneath the lens for use with the Gas Jet Manifold.
|
|
Lens holders are designed to position miniature lenses over CCD/CMOS imagers with high degree of accuracy. Lens holder must keep the lens optic axis centered on the active area of the imager. It must also keep the lens axis perpendicular to the imager surface. Some lens holders also provide special features for holding IR cut-off filters and optical low-pass filters. Lens holders are precision-molded with special plastic materials.
|
|
Adjustable Polarizer Holders
Dimensions most compact among 1" optics mounts
Both tilt and tip are controlled from aside the optical path
Ideal for dense optical schemes
Fine adjustment screws with 0.25mm pitch
Hardened inserts under adjusters
Original stabilized L-shaped flat spring
Accepts optics upto 10.5 mm thick
Tilt/tip travel range ±2.5°
Roller bearings
Lockable. Continuous 360° rotation
Horizontal and Vertical mounting
Mounting holes M4 on three sides
|
|
|
|
|
|
ECO-1 stand is the ideal support for all types of barriers of the SB series and for MDG0001 mirrors. It is practical and economical and is anchored to the floor by means of two 10 mm diameter metal anchors (not included). The base is composed of a 15 mm thick burnished iron plate, with holes for the anchors. Each post comes with 4 sliding inserts already positioned in the side splines of the burnished element. The brackets supplied with the fences or mirrors shall be fixed to such inserts. If one of the other splines is to be used (the extruded element comes with one spline per side), simply remove the plastic cover from the post, recover the inserts and insert them where desired.
If the application is particularly demanding from the viewpoint of mechanical stress, an 'L' reinforcement bracket (code: ECO-L) can be fixed between the post and the base. Normal application do not require the reinforcement bracket since the aluminium extruded structure is anchored to the iron base by means of a large screw, which goes approximately 100 mm inside the extruded element and the head of which is hosted inside the base plate.
|
|
| ... products without technical information |
| |
Flip Mirror Holder KSH 90
The swing leaf bears a wobble plate with an adjustment range of ± 0.5° and an aperture of 2". Optics with a thickness > 12 mm (normally 2" mirrors) are fixed with a plastic screw.
Optical components (such as mirrors and beam splitting paltes) having a thickness of only 10 mm can be pressed aganst three stops with the enclosed two clamping shoes and thus fixed.
The swing angle is 45°, the repeatability < 100 µrad. The swing time of the motorized version is about 1 s.
- for use with SYS 90
- black anodized aluminium alloy
- mountable onto pin or slide
- manual operation or motorized
|
|
|
This kinematic mount is designed for ultrathin nonlinear crystal positioning. The mount accepts ring holders of Ø25.4 mm and thickness up to 10.5 mm. The housing is stopped by a rest-flange inside the central aperture of the platform, and is secured by a threaded retaining ring.
|
|
The Laser Mech Lens Mounting System solves the problem of lens removal for replacement and inspection. By using a simple cartridge mounted lens inserted into a side slot in a permanently positioned manifold block, the problems of the traditional threaded, axially inserted lenses are avoided. This innovative mounting method allows removal and replacement of the lens in seconds with no readjustment of the optical alignment and without the removal, replacement or disassembly of any other part of the optical system.
Each assembly consists of a lens mount manifold block with very fine, adjustable lens centering screws and a spring-loaded, lens holder assembly to hold the lens. The lens holder contains all the seals necessary to pressurize the space beneath the lens for use with the Gas Jet Manifold.
|
|
|
ROLYN Mirror Mounts are designed to give the very best combination of economy and performance. There is no glass-to-glass contact. Clear aperture obscuration caused by the plastic mirror holders is minimal. These three holders form an adjustable rigid orthogonal kinematic mount for the mirror which resists vibration and handling. Black anodizing minimizes reflections. Mirrors are not supplied with the mount.
|
|
As you scan through our various mounts we have a selection of Single Circular Filter Wheel Mounts, a Universal Stand Mount, Compensated Circular Filter Mounts & a 8 Position Filter Mount.
* Compensated Linear Filter Mounts
* Degree Scales
* Mounts
* Storage Boxes
|
|
|
The Universal Mirror Mount/Platform 840-0052 is suited for precise adjustment of standard mirrors which can be directly bound to it. The mount may be used in horizontal position as a tilt table. Then it can be used to align opto-mechanics around two axes. For such mounting the mount has an M4 hole on its back
|
|
Adjustable Polarizer Holders
Dimensions most compact among 1" optics mounts
Both tilt and tip are controlled from aside the optical path
Ideal for dense optical schemes
Fine adjustment screws with 0.25mm pitch
Hardened inserts under adjusters
Original stabilized L-shaped flat spring
Accepts optics upto 10.5 mm thick
Tilt/tip travel range ±2.5°
Roller bearings
Lockable. Continuous 360° rotation
Horizontal and Vertical mounting
Mounting holes M4 on three sides
|
|
|
|
|
|
ECO-1 stand is the ideal support for all types of barriers of the SB series and for MDG0001 mirrors. It is practical and economical and is anchored to the floor by means of two 10 mm diameter metal anchors (not included). The base is composed of a 15 mm thick burnished iron plate, with holes for the anchors. Each post comes with 4 sliding inserts already positioned in the side splines of the burnished element. The brackets supplied with the fences or mirrors shall be fixed to such inserts. If one of the other splines is to be used (the extruded element comes with one spline per side), simply remove the plastic cover from the post, recover the inserts and insert them where desired.
If the application is particularly demanding from the viewpoint of mechanical stress, an 'L' reinforcement bracket (code: ECO-L) can be fixed between the post and the base. Normal application do not require the reinforcement bracket since the aluminium extruded structure is anchored to the iron base by means of a large screw, which goes approximately 100 mm inside the extruded element and the head of which is hosted inside the base plate.
|
|
| ... products without technical information |
| |
|
Irrespective of the shape of the product to be carried, plastic component holders can be moulded to almost any desired shape and represent a cost-effective alternative to other forms of packaging. Component holders are more than just a medium in which products can be placed for safe transportation. They provide a means of temporary storage and can be made available "just-in-time" for finishing. Thermoformed component holders can be produced in sizes from 400x300 mm to 1000x1200 mm. Depending on the application, they can be designed to allow stacking or alternate stacking. Utz component holders adhere to very strict tolerances and guarantee an excellent fit.
|
|
stainless steel
sheet metal
wire
aluminium
zinc-plated sheet steel
sheet metal-wire
sheet metal-plastic material
heat-resistant metal
BUTEK Engineering is presenting uncomplicated perfect technical solution systems and optimization systems for your specific needs.
|
|
LOGILINE FUTURA® und BLACKLINE FUTURA®
The new tote box generation positioned for manual and mechanical handling.
Ergonomically formed handle holes for a comfortable carrying as well as a flat bottom for smooth transportation on conveyor belts and other material handling equipments speak for the new FUTURA containers.
Integrated vertical label holders and easily placeable RFID-tags and –systems stand for future-oriented solution systems.
FUTURA containers are light in weight, sturdy and easy to clean and are 100% compatible with the current wez ranges LOGILINE® and BLACKLINE®.
|
|
- Integrates with all automated handling systems,
Eureka is fitted with locations for robot handling in
both horizontal and vertical planes.
- Optional anti-slip hand holds for operator comfort and security.
- Can be fitted with a tamper evident security seal.
- Pimple pads on all four sides and on lid allow the easy removal
of adhesive labels without leaving a sticky residue.
- Optional card clip can be fitted to all four sides.
- Available with reinforced base for handling heavy loads.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
