EXAIR air nozzles

Nozzle Cat. No. 20101 for electric hot-air torch Reference : 20101 Cat. No. 20101is one of the four nozzle products specially designed for the electric hot-air sealing ...

This product is a Nozzle Cat that is made especially for electric hot-air torch. It measures 40 mm and has a flat edge. It is one of the four nozzle products which is designed for Cat. ...

Manufactured by Express, the Nozzle Cat No. 20103 is a nozzle attached to the electric hot-air sealing torch Cat. No. 2010. This tool allows the user to efficiently perform on all required ...

Flow: 30, 15 ft³/min
Pressure: 100 psi

... or filter/separator which is included in other Cold Gun Systems. Cold Guns produce a stream of clean, cold air at 50°F (28°C) below supply air temperature. Operation is quiet and there are no moving ...

Flow: 30, 15 ft³/min
Pressure: 100 psi

... Cold Gun System The Cold Gun Aircoolant System with a dual point hose kit produces a stream of clean, cold air at 50°F (28°C) below supply air temperature. Systems include the Cold Gun, flexible dual ...

Orifice diameter: 1, 0.25 in
Flow: 57, 22, 4.5 ft³/min

Model 1008SS Back Blow Air Nozzle EXAIR's Back Blow Air Nozzles are engineered to clean inside of pipe, tube, hose or channel. An array of holes provide a forceful 360 ...

... mm for air heaters, GRAND, Oval-G and Vento-G (Item no.: 4021) Nozzle 150 x 10 mm for air heaters, GRAND, Oval-G and Vento-G (Item no.: 4022) Nozzle ...

Tubular nozzles Nozzle 5 mm round (Item no.: 4000) Nozzle 5 mm round 150 mm length (Item no.: 4000.V) Nozzle 15 mm round (Item no.: 4005) Nozzle ...

Our speed welding nozzles and tacking nozzles in a variety of sizes for processing plastic welding wire; can be slid onto a 5mm tubular nozzle or screwed onto an M10 nozzle ...

Orifice diameter: 1.3 in - 4.3 in
Pressure: 0.5 bar - 10 bar

GZS air steam flat fan tip is ideal for gas application. They are widely used in drying processes, water removal from surfaces, flocks and water blow off.

Flow: 5.5 l/h - 340 l/h
Pressure: 0.7, 2, 3, 4 bar

These single orifice set-ups produce a flat fan shaped atomized sprays.More precise details on the spray dimensions are given in the table on the right side of the page.The spray length can reach from 1.800 to 5.200 mm depending upon ...

Flow: 2.5 l/h - 93 l/h
Pressure: 0.7, 2, 3, 4 bar

These single orifice set-ups produce narrow-angle, full cone shaped, atomized sprays with a spray angle of about 20°.More precise details on the spray dimensions are given in the table on the right side of the page.The spray length can ...

Orifice diameter: 66, 40 mm
Flow: 0.83, 30 l/min
Pressure: 0.2, 1 bar

... a sintered nozzle (brass on U025, polyethylene on U060) has to be screwed onto a supplied steel nipple which previously has to be welded on the outside of the silo, bin or weigh hopper cone. Subsequently, connection ...

Orifice diameter: 10 mm
Flow: 3.4 m³/h - 59.5 m³/h
Pressure: 80 psi - 100 psi

... and More Cold Air Guns use vortex tube technology and filtered compressed air to produce sub-freezing air as low as -30 deg F (-34 deg C) for numerous industrial spot ...

Flow: 6.8 m³/h
Pressure: 80 psi - 100 psi
Media temperature: 21 °C

... is limited. The Mini Cold Air Gun uses only 8 SCFM of compressed air and produces temperatures as low as 0 deg F. The Mini Cold Air Gun is available with a single nozzle or a dual point nozzle ...

Orifice diameter: 20 µm - 60 µm

... entrained by high velocity compressed air to create a range of micron-level spray droplets, resulting in greater surface coverage than conventional nozzles. With this more efficient use ...

Orifice diameter: 0.05 mm - 0.41 mm
Pressure: 50 psi - 200 psi
Media temperature: 80 °F

Atomizing nozzles are available in both air-assisted and airless designs. They provide a specified spray pattern that can be used to assist in combustion in fuel systems or for applying a coating in medical ...

... The RansFlex Automatic Applicator is an air atomizing, low-pressure electrostatic applicator powered by a compact power supply. The applicator offers superior atomization and a quality finish time after time. The air ...

... electrostatically or non-electrostatically. It incorporates the latest in high speed spindle technology, bell cup and shape air design to provide the best in atomization and pattern control. The bell cups are designed ...

... non-electrostatically. The 550 applicator incorporates the latest in high-speed spindle technology and the latest in bell cup and shape air design providing the best in class atomization technology and pattern control. The ...

Orifice diameter: 3 mm

... SideGate Inline option. It is perfect for part spacing as low as 18 mm, and it is available with individual tip temperature control (up to four tip nozzles) for industry-leading balanced ...

Pressure: 0 bar - 10 bar
Media temperature: 0 °C - 180 °C

... blowing technology feature. The aerodynamic nozzle design achieves the effect by maximizing entrainment of air. Each orifice is also uniquely designed to optimize the entrainment area. ...

Pressure: 0 bar - 10 bar
Media temperature: 0 °C - 70 °C

... and holes around the Laval orifice that generates a quiet, powerful and laminar air flow. This nozzle provides extremely efficient blowing that utilizes your compressed air ...

Pressure: 0 Pa - 1,000,000 Pa
Media temperature: 0 °C - 400 °C

SILVENT 973: extra-broad flat nozzle of stainless steel. Meets virtually every demand industry places upon a modern air nozzle. The design of the nozzle creates an air ...

Orifice diameter: 0.13 mm - 1.4 mm
Flow: 0.1 l/min - 11 l/min

... Exitflex, is an air assisted airless tips that integrates high-quality tungsten carbide inserts. It is capable of providing optimum erosion resistance in all situations. Even though it has a robust design ...

Orifice diameter: 0.13 mm - 1.4 mm
Flow: 0.1 l/min - 11 l/min

... Exitflex, is an air assisted airless tips that integrates high-quality tungsten carbide inserts. It is capable of providing optimum erosion resistance in all situations. Even though it has a robust design ...

Orifice diameter: 0.13 mm - 1.4 mm
Flow: 0.1 l/min - 11 l/min

Exitflex tip for EcoGun, Optima 2100 Wi Optima 2100 and Trilogy AAA Super Finish 63-589 (TC preorifice)

Pressure: 3 bar

Flat Cone 60° Coaxial Nozzle for air/oil lubrication systems.

Single Pipe Nozzle for air/oil lubrication systems.

Pressure: 3 bar - 6 bar
Media temperature: -25 °C - 80 °C

... well-metered quantities. The fluid is properly and economically fed into the centre of the air stream. With the air and fluid choke (see picture) the amount of air and fluid is finely ...

Pressure: 3 bar - 6 bar
Media temperature: -25 °C - 80 °C

... atomizer should always be fixed a little above the maximum fluid level in the tank. With compressed air applied, the fluid is carried along well-metered by the air rushing through (a ...

Pressure: 3 bar - 8 bar
Media temperature: -25 °C - 80 °C

... °C: ISOVG150 - - 2.1 ml at 5 bar compressed air - - 1.9 ml at 3 bar compressed air - - Water - - 62 ml at 6 bar compressed air ...

Pressure: 7 bar
Media temperature: 0 °C - 55 °C

... emitter points of the HE air nozzle is current limited. Being installed outside the air flow, the high-voltage points are hardly subject to fouling, if at all. The single point nozzle ...

... ionizing air nozzle is used to clean and neutralize electrostatically charged surfaces. The use of compressed air allows awkward places to be neutralized and cleaned ...

Pressure: 6 bar
Media temperature: 0 °C - 55 °C

This nozzle has been designed especially for neutralising and cleaning (small) bottles on the inside, etc. Ionisation takes place at the end of the tube from which the air is blown. The high-voltage point ...

... up cleaning of small parts, this blast nozzle features a tungsten carbide liner encased in an aluminium jacket, offering the greatest resistance to impact or flexing. Supplied with a rubber gasket, these nozzles ...

Featuring a converging entry and a diverging exit, Venturi bore nozzles create a wide blast pattern and increase abrasive velocity, ideal for greater productivity when blasting larger surfaces.

This nozzle offers a 35% larger blast pattern than a standard Venturi nozzle with only a small loss in abrasive velocity. Designed to be used on jobs where a more even dispersion of abrasive is required ...

Orifice diameter: 0.8, 1.2, 1.5, 1.8 mm
Flow: 95 l/min - 375 l/min
Pressure: 4, 6, 8 bar

"Hurricane" is a dynamic rotating blast nozzle that cleans surfaces quickly and effectively thanks to the shockwave generated by the sweep of compressed air at a frequency of 9 Hz. The ...

... supply by means of a high-tension cable and to compressed air via a common 6 mm air hose. We recommend the use of an air filter in such a way as to prevent the nozzle ...

... The nozzle entrains the surrounding air and creates a concentrated air stream, making it more economical. The nozzle is also very quiet. Like other active anti-static ...

... of a high-tension cable and to compressed air via thread G1/8” and an air hose. We recommend the use of a 5 micron or smaller air filter in such a way as to prevent the ...

Flow: 320 l/min
Pressure: 6 bar
Media temperature: 0 °C - 50 °C

AC Inline Air Ioniser for Air Gun, Nozzle and Cleaning Applications • Dust removal, cleaning on a spot area with exchangable nozzle • Can be used ...

... suspended in a gas or on a surface, without the addition of air or external gas. This technology is used for many applications: defoaming, particles agglomeration, inert blowing… No air supply • ...

Orifice diameter: 0.25 in

... capacity hollow cone spray nozzle with the finest atomization among hydraulic nozzles. • Capable of generating extremely fine spray. • Minimal clogging with free passage diameter 1.3–2.6 times bigger ...

Orifice diameter: 0.8, 1, 2 mm

New TAIFUJet® series, Air booster nozzles, Compact, Shorter body (35mm long) compared to the conventional TAIFUJet 42mm wide type with the same performance. Features - This compact air ...

Orifice diameter: 2, 1, 0.8 mm

... Minimal Air Consumption saves on Air cost • Taking in surrounding air and boosts multiplied air flow. • Uniform distribution resulting from the unique flat design. • ...

Concentric tube nozzles for air/oil lubricated systems, mainly for MQL etc.

Spray Characteristics The Delavan AL air atomising series spray nozzles offer the user a wide variety of spray patterns, flow rates and atomisation. Unlike hydraulic or pressurized nozzles ...

The AL 15 series is a pressure-fed external mix flat fan spray nozzle The external mix feature allows control of the atomization without changing liquid flow. The lighter the air pressure, the higher ...

... Spray Nozzles - Air Atomising The AL 30 series produces a wide, round spray pattern with a nominal angle of 70°. This is an internal mix nozzle, where a change in air ...

Multi-channel flat fan nozzles for air "Whisperblast®" The multi-channel flat jet nozzles of the 600.130 series generate a continuous powerful air stream. ...

Orifice diameter: 1 mm - 8 mm

Air-Injector flat spray nozzles ID3 Extremely low-drift, air-injector flat spray nozzle for professional use.

Orifice diameter: 1 mm - 6 mm

Air-injector flat spray compact nozzles IDK Very low-drift, compact airinjector flat spray nozzle with wide droplet spectrum (from extreme coarse to fine).

Orifice diameter: 25 mm

... This is a 1 inch (25mm) compressed air nozzle equipped with a very powerful rotating WhipStream. The WhipStream rotates with 10,000-12,000rpm and the impact of the compressed airflow is very impressive ...

Orifice diameter: 12, 16, 25 mm

... remove dirt and dust in the ventilation ducts with compressed air. Tornado nozzles and rotating brushes Nozzle set in different sizes and designs Air ...

Orifice diameter: 5 mm

Orifice diameter: 7.5 mm