|
|
Characteristics of the product
Heights: 8 to 40 mm (according to product) Widths: 20 to 56 mm (according to product)
Rails C asymmetrical and omega 35 mm for modular fixing of equipment.
These rails deliverable are perforated or not
Surface treatment: Rough untreated, électrozingué dichromate yellow or blue, hot galvanized Sendzimir 275 or hot galvanized with soaked.
Perforations special and put at length on request.
A range supplements clamps of fixing of cables or tubes with a diameter 6 mm to 110 mm out of steel galvanized hot with soaked, aluminum and stainless steel AISI 304 H adapted to the shaped rails and other
|
|
DSS and DSS+C Ring / Double Swivel Shackle
Double articulation allows it to line up perfectly with the sling
Tightening by Allen key
From M33 to M64 as standard; for loads from 6.3 t to 32.1 t
From UNC 1¼" to UNC 2" as standard; for loads from 14,000 lbs to 50,000 lbs
Other variants of fitting bolts on request
|
|
Eye bolt VRS in pink - can be adjusted to the direction of pull. Higher load capacities than DIN 580-Eyebolts.
Attention: Lateral loads with eye bolts acc. to DIN 580 are forbidden! With multiple-point-suspensions at 2- leg and 3 / 4-leg, the positioning of the eye bolt has to be in the direction of pull. This can only be realized with RUD STARPOINT eye bolts as they are adjustable to the direction of pull when fitted.
|
|
Self-certified with Working Load Limit (W.L.L.) and Safety factor of 5 for fastening, securing in the entertainment Industry
NOT AVAILABLE: STANDARDS EN 362 + EN 12275 certified for Personal Protective Equipment (P.P.E.) in industry & mountaineering, Climbling, Caving activities - Breaking Limit: 25Kn longitudinal / 10Kn transversal
|
|
|
|
|
|
Double Swivel Lifting Point: DSP
Double articulation allows it to line up perfectly with the sling
Two ways of tightening: either by open-ended spanner or by Allen key
Possibility of passing a cable or rope and even of adapting a ring with a large eye for those that have hooks out of proportion to the lifting ring.
From M8 to M20 as standard; for loads from 0.3 t to 2,5 t
From UNC 3/8" to UNC 3/4" as standard; for loads from 1,200 lbs to 5,500 lbs
Other variants of fitting bolts on request
Double Swivel Lifting Point + Centring: DSP+C
Double articulation allows it to line up perfectly with the sling
Two ways of tightening: either by open-ended spanner or by Allen key
Possibility of passing a cable or rope and even of adapting a ring with a large eye for those that have hooks out of proportion to the lifting ring.
From M8 to M20 as standard; for loads from 0.3 t to 2,5 t
From UNC 3/8" to UNC 3/4" as standard; for loads from 1,200 lbs to 5,500 lbs
Other variants of fitting bolts on request
Equipped with the patented CENTRING system
|
|
Our Forged Center Pull Hoist Ring integrates a solid center brace lift bail into our most popular style product. This design eliminates the possibility of spreading the lift ring in misapplications. Forged hoist rings are ideal for OEM and industrial use.
Full (over center) swivel and pivot action
Capacities up to 30,000 lbs.
Inch and metric
5:1 strength factor-alloy steel
Made in U.S.A.
|
|
Wichard offers a wide range of forged swivels used in various industrial applications.
> Large range of products forged in HR stainless steel (AISI 630)
> Several models available: with clevis pin, large bail, or webbing...)
> Outstanding breaking loads (up to 8000 Kg)
> High speed rotation
|
|
These chains are built in accordance with ANSI B29.24 and are dimensionally identical to Standard Series Drive chains, but also incorporate pins produced from medium carbon alloy steel, through-hardened, to give the chains higher working load capacity and additional resistance to fatigue.
Additionally, these chains are produced with solid rollers for increased performance when loading is high, but speeds are slow. Users of these chains should be aware that wear life may be slightly reduced due to the material and heat treatment of the chain pins.
|
|
Grade 80 alloy chain slings are often selected when operating under high temperature or rigged conditions that would abrade or destroy other types of slings. They are flexible, durable, long lasting, ductile, easy to inspect, collapsible for convenient storage, and will adhere securely to the contours of a load. The most advantageous feature of a chain sling is its ability to be repaired/ Nearly any damaged component discovered during an inspection can be repaired and restores to useful condition.
Load Estimation
In multi-leg slings, the angle between the legs is critical. The actual tension on each leg increases when the angle between the legs increases as shown in the diagram opposite. For this reason all general purpose chain slings are given a rating based upon use at 900 inc angle. The included angle between the legs should never exceed 1200.
|
|
Chain guide:
- assists to avoid jumping of the chain
- lower chain wear - higher working life
- solid, hardened design
- dimensional proposals by RUD
- rounded leading edges
- arc of contact more than 150 degrees
Stripper with de-twister
- assists stripping of the chain from the pockets
- kept on plane horizontal and vertical links
- controlled entry of the chain into the pocket wheel
|
|
THIELE hoist-chains are approved for hand-operated hoists and power driven hoists. They are available in bright, galvanised or yellow chromated.
For power driven hoists we recommend high wear resistant round steel chains in THK 8 finish. Our special case hardening process prevents premature wear.
|
|
SEB or SEB C Ring / Swivel Eye Bolt
Swivel eye bolt fitted with an automatic position recovery system for optimum orientation in the direction of the sling.
Tightening by Allen key
Permits the hook to move parallel to the supporting face of the ring being drawn at 90°
From M16 to M42 as standard; for loads from 1.6 t to 12.5 t
Other variants of fitting bolts on request
|
|
|
The original safety-engineered hoist ring. Pivots 180 degrees and swivels 360 degrees simultaneously to allow lifting from any direction. Safety factor = 5:1. Black oxide finish is standard, with cadmium plating available as a special. Swivel Hoist Rings are also available in 300-series stainless steel, with a load rating equal to 50% of the steel version.
|
|
ACTEK® SHR-Series - Hoist ring
Specials
- 5:1 Safety factor
- 200% proof load tested
- Serial numbers for traceability
- rotates 360° and swivels 180°
- Magnetic partical inspected
- Easy mounting, only one thread or hole is required
- also available as WKA-System for assembling the
tower segments of wind generators. With only six
hoisting units, 100% of your tower segments can be lifted.
|
|
Center-Pull Style Hoist Rings
Popular sized hoist rings (1/2-13 through 1-8) are offered with two or more length bolts. Use the longer lengths with softer parent materials, the shorter lengths with hard materials such as steel.
Full Swivel and Pivot Action
Rated at 5:1 Strength Factor
Material: Alloy Steel
Finish: Black Oxide
Clevis, Bolt, Pins, Base, Washer and Bushing are magnetic particle inspected
Washer: Zinc plated with gold colored conversion coating
200% Proof Tested
Drawings available in FixtureProTM CD and downloadable from the web.
|
|
- Range of movement Pivot 180º Swivel 360º
- Minimum safety factor = 5:1
- Meets military specification number MIL-STD 1365(11) or MIL-STD 209C
- 100% magnetic particle inspected
- Meets OSHA requirements
|
|
Description Safety-eye bolt
Reference 260-12-13
Please select one table row below:
D1 D3 (mm)
M12 13
M16 13
M20 16
M24 18
M30 20
M30 22
M36 22
|
|
OSR and OSR+C Ring / Outside Swivel ring
Ready to use complement to the OFT and OFT+C
The ring forms an integral part of the ensemble
|
|
Matter, completion:
Steel phosphated with manganese. Button pressure: aluminium. Example of order: nlm 07780-2110x50
Foot-note: L´anneau of lifting to autobloquant bolt is equipped d´une mobile manille: It constitutes a tool for lifting fast and simple to handle. To press the button for déverouiller balls of the bolt and to slacken it to obtain a sure locking.
|
|
CSS Ring / Central Safety Shackle
Allows a closed mould to be raised that may weigh up to 32 tonnes
|
|
Container Hook VCH 10t
Suitable for ISO container edges. A permanent connection using a VVS1/2 or a loose component for hook mounting.
Attention:
RUD-VCH hooks are not suitable for vertical lifting. Given a minimum inclination angle of 30° during the lifting process, the hook cannot automatically open.
Containers 1D, 1E and 1F can be lifted from the top edges using a 4 -leg assembly and a max. inclination angle of 30°
|
|
Self-certified with Working Load Limit (W.L.L.) and Safety factor of 5 for fastening, securing in Industry, Fishing, Marine fittings, Entertainment industry, Agriculture, DIY, Decoration
STANDARDS EN 362 + EN 12275 certified for Personal Protective Equipment (P.P.E.) in industry & mountaineering, Climbling, Caving activities - Breaking Limit: 25Kn longitudinal / 10Kn transversal
|
|
World premiere of the strongest lashing chain ICE-120
13 years after the beginning of the successful VIP Grade 100, RUD is creating the next level of innovation in chain technology. RUD is the first manufacturer worldwide who is able and allowed to produce round steel chains in Grade 120. Compared with the common Grade 80, the new Grade has a breaking force which is up to 60 % higher. When lifting, the WLL (working load limit) is up to 60 % higher and the reduction of weight is up to 30 % less.
Further technological properties like
Elongation at break and ductility
Resistance against cryogenic use
Crack arrest behaviour
Permanent durability and wear resistance
have been improved considerably.
|
|
Leaf chains
LL / J Series (from 9.53mm to 76.20mm pitch)
LH / BL Series (from 12.70mm to 50.80mm pitch)
AL Series (from 12.70mm to 50.80mm pitch)
Clevises and pear shaped links
Lifting and extending Galle chains
|
|
|
Leaf Chain, commonly known as "Balance Chain", is the most simple of steel chains, consisting only of link plates and pins. This chain is subject to ANSI standard, and suitable for hanging, balancing, or motion transmitting applications. Plates are connected by pins and hold the tension loaded onto the chain. Pins are to resist the shear force from tension loading applied by the link plates and to withstand abrasion from the middle plate holes when the chain articulates.
|
|
DSR and DSR C Ring / Double Swivel Ring
Double articulation allows it to line up perfectly with the sling
Two ways of tightening: either by open-ended spanner, or by Allen key
From M8 to M30 as standard; for loads from 0.3 t to 6.3 t
From UNC 3/8" to UNC 1" as standard; for loads from 1,200 lbs to 10,000 lbs
Other variants of fitting bolts on request
|
|
Hangzhou Donghua Chain Group Co., Ltd is the biggest chain manufactory in China. This company is specialized in producing all kinds of standard chains and special chains, e.g. A or B series chains, automobile chains, stainless steel chains, combine harvester chains, heavy-duty cranked link transmission chains, stereo garage chains and maintenance-free chains etc.
We can provide all kinds of Hoisting Chains such as Car parking chains, Leaf chains, Multiple plate bearing pin chains and Hoisting rollerless chains.
If you are interested in our products please feel free to contact us by e-mail.
zhangxb@dhchain.com
|
|
|
We supply a full range of grade 80 alloy fittings, our products include connecting link, eye self locking hook, clevis self locking hook, swivel self locking hooks, cradle clevis grab hook, eye hooks, master link, master link assembly, shortening clutch, shackle, etc.
|
|
|
|
Chains, Cables, Ropes, Hooks, Pulleys
