|
|
Dynfile® II Abrasive belt Machine
- Grind, deburr, blend and polish
- Work on metal, plastic, fiberglass, composites, rubber, glass and stone
- Lightweight, 7° offset design. Grinding head pivots 360°
- Grind off contact wheel or platen pad. Finish & polish using slack of belt
- Also available in a Versatility Kit |
|
Dynafile® Grinding belt Machine
- Grind, deburr, blend and polish
- Work on metal, plastic, fibreglass, composites, rubber, glass and stone
- Work in areas as small as 3/8" diametre
- Also existing in a Versatility Kit |
|
Choose Atlas Copco professional grinders and boost your productivity!
Offering high power-to-weight ratios, Atlas Copco grinders give you maximum material removal with minimum effort, thus boosting your productivity. Available in a wide range of versions covering virtually every application, these robust tools are extremely reliable and simple to maintain, with long service lives.
Their ergonomic design, including efficient noise and vibration damping, makes them easy on the operator in demanding applications.
For a completely new experience, try the GTG and GTR 40 Turbo grinder - twice the power, half the weight and beyond your imagination! |
|
800 Watt Angle Industrial grinder W 8-115
High-powered angle grinder with extra high cooling capacity for fast work progress even under the toughest operating conditions
Sturdy, durable Metabo marathon motor
Metabo dust protection technology for extremely long service life of unit: marathon motor with winding protection grid, fully enclosed switch, labyrinth seals on the ball bearing manufacturers, ...
Ergonomic housing design with distinctive indents for comfortably holding the device during clearing and roughing, as well as slip-proof holding of the unit
Diecast aluminium gear unit housing: robust and resistant to wear
Metabo S-automatic torque limiting professional clutch: to limit any sudden reverse torque that can occur if tools jam or get caught.
Additional vibration damping Metabo VibraTech (MVT) handle for convenient continuous operation
The tool-free adjustment and removal of the protective cover allows you to adjust the device for any application in seconds
Metabo winding protection grid to protect the motor from abrasive effects
Highly durable switch-off carbon professional brush with dust protection housing |
|
Nitto Kohki´s "MYTON" Compressed air grinders:
- A wide variety of models are available to a particular job
- Rated Air Pressure: 6 bar
- Free Speed: between 7.100 and 22.000 rpm
- Depressed center wheel: between OD 58 and OD180 mm
- Mass (Weight): between 0,5 kg and 3,4 kg |
|
Levibreton KGP
CONTINUOUS BELT POLISHER FOR PORCELAIN GRANrTE TILES "LEVI-BRETON Mod. KGP"
Machine used to grind and polish porcelain granite tiles and granite strips. Some models are also equipped with 4 calibrating spindles manufacturers Mod. MC-8.
The dressing/polishing units hold the special Breton, high-removal heads Mod. SG-6 with oscillat-ing abrasive sectors and 540 mm diameter.
All the machines are controlled by a Siemens S7 PLC SUPPLIERS with display and programming professional keyboard controlling all the automatisms.
|
|
2FSM 2" Industrial sander Multi-position vertical or horizontal
2" x 48" belt, Vertical or Horizontal Position.
1/2 HP motor, 3450 RPM, direct drive, 5" contact wheel
Tilt work table, removeable platen
Full hinged OSHA guard for quick belt change.
Pre-set belt tension, one knob belt tracking.
4500 SFPM belt speed, WT. 48 lbs.
Model: 2FSM
Other products available: |
|
Developed from the well proven belt sanding machines for woodworking in outmost robust and long
lasting construction especially for the hard requirements in the metal working.
Special machines on request. |
|
- Model HS-24
- Sanding speed 1000RPM
- Grinding belt size 158"x4"
- Table area 48"x24"
- Table height from floor 830mm
- Motor 3hp |
|
S6MS, 6" industrial belt sander
Industry standard. 3 HP !! Real workhorse !! Every shop needs one !! Also available in 5 HP and in 6" x 60" professional belt!
6" x 48" belt, variable positons, direct drive, 1 lever quick belt release !!!
Cast iron frame, Full OSHA safety guard, Heavy duty steel stand.
3 HP motor 3450 RPM, 1 phase or 3 phase, manual switch, 3500 SFPM
Reversible platen 6 1/2" x 14"
Cast iron work table 6" x 10" with 1/2" x 1/8" slot
Option: JIC controls
Model: S6 professional sander head only, less motor
Model: S6M-1 3hp, 1 phase, 220, LESS stand.
Model: S6M-3 sander, 3 hp, 3 phase, LESS stand
Model: S6MS-1 , 3 hp, 1 phase, 220 volt, w/Stand ( 110 volts @34amps)Model: S6MS-3, 3 hp, 3 phase, 220/440 volt, w/Stand
Model: S6MS-5 5 HP, 3 PH other features same as above.
Model: S660MS 6" x 60", 3 hp, other features same as above.
Other products available: |
|
The Model 600 machine provide fast and effective graining, finishing, fetling and surface conditioning. Designed to run nylon, flap, wire, and buffing wheels. Variable speed options extend the range and capability of the Model 600 machine.
Composite, vitreous, and stone wheels are prohibited on the Model 600, and Burr King professional grinders.
The Model 800 machine provide fast and effective graining, finishing, deburring and surface conditioning. Designed to run nylon, flap, wire, and buffing wheels. Variable speed options extend the range and capability of the Model 800 machine.
Composite, vitreous, and stone wheels are prohibited on the Model 800, and Burr King grinders.
The Model 1000 deburrs, grains, polishes, cleans, descales, and buffs at a single station, a single machine, and a single operator.
The Model 1200 deburrs, grains, polishes, cleans, descales, and buffs at a single station, a single machine, and a single operator. |
|
The circular industrial vibrators can be used for the surface treatment of a multitude of parts and within the framework of very different processes.
Their range of applications goes from aggressive fettling, with the shelf to the polish-mirror of delicate parts, of the émerisage of outline until scouring before galvanization.
Various solutions exist (solutions uninterrupted, etc...)
- Circular vibrators of the range CD
- Vibrators of range CB
- Circular vibrators of the range CM
|
|
Burr King vibratory bowls are ideal for bench top polishing, descaling, deburring, and surface conditioning. Units are fast, quiet, and effective. Available in 3 qt, 10 qt, and 20 qt volumes.
- Flow-Through Design
- Heavy Polymer Bowl
- Adjustable Amplitude (Except 110)
- 1200 Pulses Per Minute
- High Energy
- Power Cord & Switch
- 120v/60HZ (110, 150S, 200S)
- 50 HZ available on models 150 and 200S, consult factory. |
|
S612 & S612V Combination Industrial sander With Vacuum !! 3 HP !!! Made in USA!!! 6" x 48" professional belt, 12" Disc, Vacuum Base
Available with OR without manufacturers of dust collector. 3HP 1PH 220 OR 3HP 3PH 220/440 volt. ( Specify voltage) Manual switch with overload protection.
Built in 100 CFM dust colletor base with cartridge filtration.
Quick change belt, pre-tensioned one lever belt change...FAST !!
Models:
# S612-1 No vacuum, 1 phase/220 volt
# S612-3 No vacuum, 3 phase 220 or 440 volt
# S612V-1 Vacuum base, 1 phase/220 volt
# S612V-3 Vacuum base, 3 phase 220 /440 volt
Dimensions: L12" x W14" x H60", Weight: 500 lbs.
Specifications:
Industrial belt sander
Work Table- Cast iron 6" x 10" with 1/2" x 1/8" slot
Platen- Steel 6-1/2" x 14"
Belt- 6" x 48" - 2800 SFPM
Disc grinder
Work table- Cast Iron 8" x 14"
Disc- 12" aluminum disc, 5/8" arbor Speed- 2500 RPM
Other products available:
|
|
- 20,000 RPM cut-off tool uses 3" (76 mm) diamond cut-off professional wheels with 3/8" (10 mm) mandrel
- An attached, non-marring plastic flange protects surfaces during cutting
- .7 hp motor delivers cutting speed power
- Tool is equipped with 94300 Dynaswivel®
- A 3" (76 mm ) diamond wheel with integrated mandrel is required (sold separately)
- Unique shroud and flange design add to existing cut-off family
- Ideal for trimming fibreglass/composite parts |
|
DS10 10" disc grinding machine
Heavy-duty, all steel
Tilt table, 45 degrees down - 15 degrees up
Optional: MG10 mitre gauge
10" aluminum disc
5/8" arbor
6" x 11" table
1/2 HP (110/220V), 1 PH TEFC motor
48 lbs.
Model: DS10
Other products available: |
|
- Disc grinder and Random Orbital sander Combination
- 12,000 RPM Dynalocke® is truly "two tools in one", easily changing from a rotary Disc Industrial sander to Random Orbital Sander with the flip of a switch
- Includes low profile, premium urethane sanding pad
- Very lightweight with ultra-smooth sanding performance
- Ideal for paint stripping and blending |
|
SXE 450 TurboTec
Multi-purpose machine for sanding even and cambered surfaces, wood, plastics, non-ferrous metals, sheet steel
Rotating and additional oscillation movement of backing pad for optimum finish and high material removal
Variospeed (V) electronics for infinitely variable speed change
Thumbwheel for preselection of speed
TurboBoost professional switch: allows additional power reserves to be employed for achieving maximum removal
No scratches while placing the running machine on the material owing to the built-in support plate brake (Power Control System). No more time-consuming finishing work due to scratches. Ideal for sanding very thin material (e.g. veneered surfaces) and sensitive areas.
One-of-a-kind ‘Duo’ oscillating circuit; setting 1: (small oscillating circuit) up to 100% higher surface smoothness; setting 2: (large oscillating circuit) up to 70% increase in removal power
Removable side handle
Dust-proof professional ball bearing for long service life of the machine
Sturdy aluminum die cast bearing manufacturer housing
Quick sheet change by velcro-faced backing pad
Vibration damping, non-slip rubber support on the machine housing and the handle
Dust extraction unit with Intec industrial filter system, multiple cleaning
External extraction possible: a industrial vacuum cleaner can be connected |
|
Nitto Kohki´s "BELTON" Compressed air sander:
- Suitable for sanding jobs in narrow spaces, recessed corners or on
curved surfaces
- 5 models available
- rated air pressure: 6 bar
- free speed: between 14.000 and 17.000 rpm
- belt speed: between 1.000 m/min and 2500 m/min
- mass (weight): between 0,6 kg and 2,9 ,kg |
|
Angle Die Professional grinders
The Atlas Copco governed die grinders offer the very best of productivity, reliability and ergonomics.
Best performance, low weight The speed governor keeps the rotational speed close to the maximum free speed when feed-force is applied. The use of a speed governor enables a smaller and smoother design while maintaining access to power.
Built-in ergonomics for the best working environment The unique suspension of motor and professional spindle of the LSF series prevent unpleasant vibrations from being transferred to the operator's hand. Well tuned motors and air outlet keep sound levels remarkably low.
Minimized burr consumption A suspension of the spindle prevents the burr from chattering. Apart from a smoother die grinding operation, the burr consumption is minimized, in many applications by 20 %.
Wide range You can choose the suitable model for your application - from heavy duty versions to small, angle die grinders. Short and extended models (E).
LSF28 ST030 is lubrication free for clean environment. |
|
CP Industrial professional grinders:
These tools are suitable for high professional production rates such as those on production/ assembling lines, where high durability is required and the tools are used frequently. Our industrial tools combine the best of quality, durability and ergonomics for your most demanding applications.
CP RediPower grinders:
RediPower tools are suitable where the tool is used intermittently for industrial maintenance or non-intensive production. |
|
LIGHTWEIGHT DYNINGER®
- Air-Powered Abrasive finishing tool to use with Spindle-Mount, Arbor-Mount and Eyelet Sanding Stars.
- Excellent for use on wooden parts, moldings, raised panels and intricate profiles.
- Tool includes 94407 Air-Flow Control Dynaswivel® professional fitting for maximum tool maneuverability and control.
|
|
Die professional grinders of the brands Yokota are used for most light dressing / fettling
applications on fabrications and die setting sets. |
|
|
|
Sanding and polishing tooling
