Friction sheet feeders

P. 1
of goods due to products falling from the slip sheet ?h?n Multiple sheets feeding or pick up Keep in mind that slip sheets being used in high volume manufacturing and distribution, that any problems arising from slippage or even multiple sheets feeding can aggregate into higher costs. Grip?N Slip

P. 2
Specifications ?h?n Construction: A thin Grip Sheet glued on Kraft liner board ?h?n Type of glue used: PVA ?h?n Color: Brown ?h?n Dimensions: ?h?n Maximum width : 73?? (1854 mm) (including tabs) Maximum length : 100?? (2540 mm) (including tabs) ?h?n Tabs: ?h?n Quantity: 0 to 4 ?h

P. 23
screens fines chutes feeders light duty b limitations b temperature max 80 c min 50 c ik provides wide range low friction sheets to promote bulk materials flow b 23 b

P. 20
properties making it the best choice many applica tions very good wet applications fine particles sliding wear can be installed using square neck bolts clamped position b wg9000 b this is the hardest the three sheetings that sandvik supply the hard surface makes it suitable appli cations where low

P. 22
is high quality flow b b promoting product available various molecular weights its low friction makes it suitable applications fine size bulk materials b b antistatic polyethylene sheeting black b sandvik wg2000 virgin is high performance polyethylene material the best abrasion resistance the three

P. 10
wear plates full steel backing is an allaround wear protection that can be tailormade to fit most applications from light to mediumduty it is mainly used wet applications b b wt9000 b wt9000 is the hardest the three polyurethane wear plates that sandvik supply the hard surface makes it suitable

P. 17
hoppers chutes vibrating feeders transfer points bins silos spouts general wear protection b limitations b do not install applications any amount oil present temperature max 80 c min 25 c high quality wear resistant sheeting 40 60 shore 17

P. 3
-M(V) at any time. Mobile and flexible Multi-Clamp Suction Plate VC-M-SP(V) Safe working Optimized holding forces through special developed friction pads Optimal sealing Special sealing cord, below and above, to compensate for the irregularities of the workbench and the workpiece Flexible adaptation

P. 4
common compressed air supply due to the integrated, pneumatic ejector. Therefore no additional vacuum pump is necessary. Simple to change Clamping lever for attaching and loosing the Multi-Clamp suction plate Easy to connect Hose connection for compressed air supply

P. 6
of tubes with pneumatic quick connector) Friction pads REIB-INS Sealing cord DI-SCHN Article number 10.01.12.02055 10.01.12.02054 10.01.12.02000 10.01.12.02056 Multi-Clamp Accessories Type Complete system Multi-Clamp VC-M* Multi-Base VC-M-B Multi-Clamp suction plate VC-M-SP 160x160 Multi

P. 2
. The lightweight construction of the Multi-Clamp guarantees a maximum degree of flexibility for simple and quick operation. The clamping system can be used on almost any flat surface and consists of the Multi-Clamp suction plate and the Multi-Base which enables to swivel and rotate the workpiece. The complete

P. 5
-Clamp suction plate 160 x 160 mm for flexible usage with almost every workpiece Multi-Clamp suction plate round Ø 210 mm especially for applications with wooden workpieces Multi-Clamp suction plate oval 200 x 55 mm and 300 x 100 mm for clamping of narrow workpieces Vacuum Clamping System Multi-Clamp VC

P. 6
HOKE Metering Valves 5 Micromite® 1600 Series Materials of Construction DESCRIPTION MATERIAL 1 BODY 316 stainless or brass 2 O-RING Fluorelastomer or Buna-N 3 O-RING Fluorelastomer or Buna-N 4 PANEL NUT Brass 5 WASHER Fluorelastomer 6 WASHER 304 stainless 7 STEM AND PIN 316 stainless 8

P. 2
metering valves Milli-Mite® 1300 Series Forged Metering Valves Features & Benefi ts ? Metering accuracy - 18 turn displacement of stem provides unparalleled performance and repeatability ? 1° and 3° stems provide a wide fl ow range with ultra fi ne metering control ? Panel mounting

P. 3
2 HOKE Metering Valves Milli-Mite® 1300 Series Materials of Construction DESCRIPTION MATERIAL 1 Handle, black anodized Aluminum Alloy 2 Set Screw Alloy Steel 3 Graduated sleeve 302 SS 4 Metering Stem 316 stainless 5 Panel nut Brass 6 Upper spacer 316 stainless 7 Dyna-Pak® wafer Tefl on

P. 9
. See fl ow curves for details. ? Panel mounting is standard on all valves ? Bonnet lock prevents accidental disengagement of bonnet. ? Special High Tolerance NPT Thread Typical Applications ? Metering liquids and gases on analytical equipment ? Laboratory sampling ? Gas chromatography

P. 10
HOKE Metering Valves 9 2300 Series Materials of Construction Dimensions Dimensions for reference only, subject to change. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 FLOW PATTERN A & B CONNECTIONS PANEL MOUNTING DIMENSIONS D D? E F F? H H? PANEL THICKNESS HOLE SIZE GLOBE ¼ ? NPT

P. 2
in phase to the main product by using friction and positive placement feeders. Products can be held in place by means of hot melt tipping. ? Newly designed "touch screen" panel for setting all key functions and minimum make-ready. A feature to this system is the production report capability showing

P. 1
- prearrangement for labeling head or inkjet - paper wrap - tightwrap to stretch the film and optimize quality - shrink tunnel - zip code reading system - selective feeding for personalised inserts 2/08 - 1000 - GB www.tipolitografiafg.com 3467 136.49? 1520 59.84? 2500 98.42? 2600 102.36? 1900 74