|
|
A unique hinged design eliminates the need to disassemble the clamp prior to installation and allows the installer to close the pipe clamp with one hand without turning a screw. Once the pipe is installed, simply tighten the screw to secure the pipe in place.
The cleverly designed pipe clamp requires only one screw and hinge. The all steel design of the patented closing mechanism means the strength is not significantly reduced by exposure to heat.
|
|
One-piece, self locking pipe clamp for safe and efficient installation of cables and tubes
- Simple mounting without locking screws
- Fast mounting
- Listed by IAPMO R&T/UPC®
- Approved by KIWA®, UL®
- Halogen free as per IEC-Norm 754-2
- Burning behavior as per UL94 HB
- Clamping range 8 - 127 mm
- Low height
- Different plastic materials possible
Since 1975 the self-locking pipe clamp CLIC has proved itself millions of times. Cables and pipes fixed with «Swiss Quality» are fast and securely fixed throughout the world.
Today, system solutions (pipe clamps, screws, plugs and accessories) are required, for instance in telecommunications. Consulting during the phase of planning, becomes more and more important. A long experience in business and our internal development division have allowed many individual solutions in collaboration with our customers engineers. Our production is able to preassemble tailor-made CLIC systems even at short notice.
CLIC ideally covers the demands for fixing points in sensitive environments. In many tunnels coaxial cables for radio and mobile telephone systems are openly mounted. The performance may not be impaired by interference from metallic parts. The plastic pipe clamp is therefore the best solution for the installation. |
|
Stop Collars with Rubber Bumpers
The unique Threaded Fine-Adjust version makes stroke adjustment even easier! Simply slide along the shaft and clamp in place. Then rotate the knurled portion for up to 1/4" of fine stroke adjustment. Ordinary stop collars are also available.
Available On:
Dual Slides: 5/8" Bore 1" & 1-1/2" Bore
Single Action Slides: 5/8" Bore 1" & 1-1/2" Bore
Gantry Dual Slides: 1" & 1-1/2" Bore |
|
This is the classic product group. You'll still find products here from the early years which are still very popular with the installers and are processed in large quantities to day.
The newer product series of the anchor and C-profile rails with the accompanying clips and yoke clamps have still a high significance in the everyday workflow, too. |
|
| ... products without technical information |
| |
Style 360 Repair Clamp
The Dresser® Style 360® repair clamp offers simplicity and ease of installation. Just wrap the clamp around the pipe, drop the bolts in place and tighten. It's that simple! Moreover, special one-inch long nuts allow the use of a standard deep socket wrench for complete tightening. In the popular 7.5 inch clamp width, there is also a third nut so
the middle nut can be used to pre-tighten the clamp.
Additionally, the smaller sized clamps feature a flexible band which means less holding force is required while tightening.
With the "360" clamp you can repair holes, breaks and splits in the pipeline. You can use it where pipe ends are separated, or where ends are deflected up to 4 degrees or 1/8 inch. Or you can join two pipes with a variation of 1/4 inch outside diameter.
Clamp features include a tapered gasket with a gridded design and the spanner is molded flush with the gasket to prevent "hang up." The "360" has a stainless band, lugs of rugged ductile iron and bolts of corrosion-resistant Dresserloy. |
|
Style 194 Service Saddle
For use on PVC Pipe (IPS, OD)
Offers 360-degree support for taps off plastic mains
Designed with plastic pipe in mind, the Style 194 service saddle provides a low cost efficient means for supporting the pipe where service taps are made.
Check these advantages:
- Simply "wraps" around the pipe. One bolt to tighten.
- Full 360-degree support of the pipe, with designed-in safeguard against overtightening. Cannot deform the pipe.
- Recessed rubber compound gasket is confined, cannot blow-out, or cold-flow to weaken the seal.
- Boss furnished with either corporation or IPT threads, to suit your standards. 3/4" and 1" tap sizes available.
- Rugged malleable iron bodies are galvanized for long service life. Bolt is corrosion-resistant Dresserloy, cadmium plated. |
|
| ... products without technical information |
| |
|
|
