|
|
Using the CENTOR technology, the CENTOR W digital torque gauges have a very large graphic display and show a maximum amount of information for more efficient measuring: they show the current reading and the peak value at the same time, and a bar graph to show the operator whether they are close to their maximum capacity. If necessary, the backlighting can be used to further enhance reading comfort.
Its advanced measurement chain enables it to use a sampling rate of 1,000 Hertz with a resolution of 1/10,000 FS and a total error of less than 0.5% FS.
Many other functions complete the possibilities of the gauge:
the Set point functions can be used to carry out “OK, NOK” tests: a symbol appears on the display.
The fully programmable RS232 output sends the data to a PC. A digimatic output can be used with Mitutoyo statistical printers.
|
|
|
With the boxes of measurement of couple Weber: finished the long discussions concerning the couples of screwing.
|
|
Equipped with a built-in Transducer the EZ serie may be used to calibrate quickly and accurately every kind of fastening tools (torque wrenches, electric and air screwdrivers).
Memorized readings can be easily transfered to any kind of computer or printer through RS 232C port. With The EZ SMART version enjoy extreme measuring flexibility and full traceability of your tools thanks to additional functionalities.
External transducers may be connected to the EZ SMART becoming a small-sized portable torque readout to achieve torque audit along the assembly line!
- Easy to use scroll menu
- Real time clock
- 500 datas FIFO memory capacity
- RS232 output
- Mini/ok/Maxi torque limits
- Peak, first peak, track measuring mode
- Automatic and manual reset
- Calibration display
|
|
|
Proper torque measurement is critical in many assembly operations. AIMCO provides expertise and measurement equipment for all three phases - before, during, and after assembly. Tool testing and capability studies can be easily performed in the tool crib or lab. Fine tuning of torque settings and process verification are achieved on the assembly line with rotary transducers. Use our complete line of electronic wrenches for final residual torque testing.
|
|
Simple and yet complete, the CENTOR First uses efficient technology to simplify force measurements, in tension and compression.
A big display shows the force measured in tension or compression in the unit selected by the operator: newtons, kilograms or pounds. The bar graph completes the measurement.
The 3 keys make it very easy to use this force gauge and access the essential functions: measurement of the peak tension or compression value, resetting to
zero, and changing the measuring units. It is an ideal tool for basic tests during production. Its metal casing, protected by an elastomer overmould, gives it
exceptional strength.
The internal sensor stands up to an overload of 200% of its maximum capacity.
Simple, precise, robust, supplied with its own carrying case, mains adaptor and certificate, ready for use, it is the basic tool for force measurement.
|
|
|
|
|
|
Measuring System PHYSIMETER® 906 MC-B
The measuring system PHYSIMETER® 906 MC-B has been designed for the determination of the mechanical parameters force or torque on the basis of wire strain gauges. The instrument can be supplied with an integrated or an external sensor. For the power supply a block battery of 9 V is required (standard article) or alternatively a plug-in power pack (option). For easy handling the instrument is provided with the functions On/Off, reset and indication of peak value (upper and lower measuring value). In the standard version of the instrument the load introduction takes place at the bottom. Upon request, the load introduction can also be effected on the top of the instrument. The ergonomically designed housing, made of anodised, high-strength aluminium, is provided with threaded bores at the front side so that an unproblematic connection to the ERICHSEN testing machines is guaranteed - as it was also ensured when using the preceding models of the tensile and pressure testing instruments. The instrument is perfectly suitable for mobile as well as for stationary applications.
|
|
Using the Centor technology, the Centor W Easy TM digital torque gauges have a very large graphic display and show a maximum amount of information for more efficient measuring: they show the current reading and the peak value at the same time, and a bar graph to show the operator whether they are close to their maximum capacity. If necessary, the backlighting can be used to further enhance reading comfort.
Mounted with a non removable external mini torque sensor, it allows you to measure very small torque with the high accuracy required.
Its advanced measurement chain enables it to use a sampling rate of 1,000 Hertz with a resolution of 1/10,000 FS and a total error of less than 0.5% FS.
Many other functions complete the possibilities of the gauge:
- The Set point functions can be used to carry out “OK, NOK” tests: a symbol appears on the display.
- The fully programmable RS232 output sends the data to a PC.
- A digimatic output can be used with Mitutoyo statistical printers.
|
|
|
The Mecmesin range of digital torque gauges and systems is based upon the AFTI display unit, together with an appropriate `smart` torque sensor and gripping fixture.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|
