Special handling and lifting tools

The RGS Linear Rail is a screw driven rail system that offers exceptional linear speed, accurate positioning, a narrow base and long life in a compact, value-priced assembly. The length and speed of the RGS is not limited by critical screw speed, allowing ...

... The ZOLLERN grippers are used for reliable handling in the production process and are used in different application areas. Specially developed for the respective requirement Sturdy gripper design Low-maintenance Maintenance-friendly design Compact ...

... AP&T has a wide range of destackers/stackers that can handle everything from small high speed components to large automotive parts such as doors, roofs, hoods and body sides. Speeds range from 10 to 40 SPM, and we can handle different kinds of materials ...

... Largest selection anywhere Scissor or parallel styles with either rack & pinion or linkage Single gripper lift capacities up to 9.0 lb Repetitive accuracy of 0.2 mm (0.008 inches) ...

... Perfect for partial output. We optimise partial handling with clearing systems specially developed for the fineblanking and forming process to guarantee reliable partial output even at the highest stroke rates. Advantages. No impact points on parts, ...

Load limit: 200 kg - 2,000 kg
Lifting height: 300 mm - 1,200 mm

The EXPERT-TÜNKERS Lift Powered Rollerbeds are an important element of the non-linked body-in-white production. Each station contains two mechanically synchronized lift columns and a rollerbed with an additional drive unit for the horizontal skid transport. ...

... V-Belt Tensioner with Mounted V-Belt Pulley Material: Housings up to Ø 78 mm made of sintered steel, over Ø 78 mm made of grey cast iron GG20, lever St52, V-belt pulley cast steel. Matching narrow V-belts DIN 2215 und DIN 7753.Pulley with sealed ball ...

... The ROSTA tensioning element type SE-B (Boomerang) compensates the slack in extremely long chain drives. The ROSTA tensioning element type SE-B (Boomerang) compensates the slack in extremely long chain drives. The Boomerang with its bended double arm, ...

... Single guide post type -Actual output of cylinder When the air pressure is 0.5MPa, It is Approx, 600 x 0.7 = 420 N. -Other cylinder type (manufacturer) -For operation Refer to the dimension of the casing hole below for installation. ...

... Magnetic Stacking and De-Stacking Conveyors Bunting® Stacking Modules can be configured to take sheets or blanks from your cut-to-length operation and then transfer, index, and stack them at pre-selected destination points. Stampings can be conveyed ...

Grip strength: 5 N - 220 N
Stroke : 140, 85 mm

... Grippers Plug + Play on collaborative robots Eliminate changeovers & reduce tooling costs Pick parts of different size and shapes Automate all your applications with one gripper Program your application in minutes Applications The ...

... About WGS grippers and cylinders Grippers are normally used to pick sprues, but are often also used for parts picking, especially when the surfaces of the parts are not flat enough to use vacuum cups. Gripping pliers have the additional advantage that ...

... Denesting machine for trays and lids, picks products from a loading stack and places them horizontally on a packaging line Clippy Denester is a denester machine, that is a pick and place device especially designed to denest thermoformed trays and ...

... CEILING MOUNTED SYSTEMS use the structure for support, as the rail is mounted either perpendicular or parallel to the ceiling beams. Should overhead obstacles be present, drop rod hangers with sway bracing can be supplied so that the fall protection ...

... WINKEL pallet lifter with chain WPH 1 productfacts -with load frame to suit any conveyor -motor in top position -load capacity 0.5 - 3t with WINKEL bearings -up to 40 m lift height -max. 2 m/sec. lifting speed -low maintenance ...

... Adjustable for different pallet widths. The PalManager Multi is used for stacking of up to 14 pallets or as pallet magazine from where the operator can collect one pallet at a time. The pallet magazine can be set for automatic operation. •Safe ...

... Complete compatibility with conveyor-loading SPEA testers The Automatic Board Handling Equipment – designed and manufactured by SPEA – allows automatic loading of PCB and devices from Rack to Tester, and from Tester to Rack. The handling equipment ...

Rail length: 2,000, 3,000, 1,800, 2,500 mm

Capacity: 50 t

... For increased productivity in complete safety Designed to cater for difficult quick die change conditions, the SERAPID PPS pusher is easy to install on an existing press and allows dies to be handled and positioned accurately, effectively and safely: • ...

Grip strength: 670, 624 N
Stroke : 8 m

... Configuration Options: S: Short stroke B: Ventilation at bottom P: Dust cover IP64 NO/NC: Self-locking form H: High temperature resistance For the standard pneumatic two-finger gripper, FOUK adopts high-strength materials and the surface ...

... Pallet magazines automate pallet supply. Whether stand-alone, mechanical or integrated into your production line, this solution saves time, space and reduces manual handling. It automatically stacks and unstacks up to 40 pallets. Various versions ...

... EMS Waste Transport and Hooklifts - Designed for efficient collection and transportation of municipal solid waste. - Suitable for use in waste transfer trailers, transfer stations, and sorting facilities. - Can be adapted for medical waste sterilization ...

... Foot-pedaled Hydraulic Drum Handlers with U-shaped Base 1. Easy operation of foot pedaled hydraulic pump; 2. Ergonomic solution for lifting, transporting and placing drums; 3. Works with most rimmed drums - steel, poly and fiber; 4. Heavy-duty design ...

The Mobile Transfer Cart is powered by a battery, which serves as the energy source for the flatbed cart. DC power is supplied to the control box, allowing the cart to start, move forward, and reverse through either a wireless remote control or a wired ...

Introducing PacMan’s High-Capacity Tilters: your solution for safe and reliable 90-degree tilting. Engineered for extra-large and heavy equipment, these tilters ensure smooth operations in demanding environments. With robust construction, they effortlessly ...