Voltage: 20, 30 V
Current: 10 mA
Frequency: 10 Hz - 10,000 Hz
Accelerometer Charge Conversion The 55CA Charge Amplifier conditions and amplifies charge-mode accelerometer signals. It is a rugged device designed to be used in engine test cells and other environments where charge-mode ...
Voltage: 1 mV - 4.5 mV
Current: 4 mA - 20 mA
Housed in an IP50 in-line enclosure, Mantracourt’s In-Line Amplifier (ILA) converts strain gauge or load cell inputs into a high stability 4-20 mA output. Its small design enables it to be easily integrated into compact ...
Mantracourt Electronics Ltd
Voltage: 990 V
Current: 630 A
Power: 14, 28 W
... effective MRI Gradient Amplifier for 1.5T high field MRI systems Product features -Cost effective three-axis Gradient Amplifier cabinet -990V / ±630Apk / 230Arms -Immune to condensation ...
Prodrive Technologies
Current: 8 A
Power: 1,912 W
This single-axis, Direct PWM amplifier is designed to fit into a standard 3U UMAC rack. It is intended for driving AC induction, permanent magnet brushless, linear, and brushed DC motors. ...
Current: 20 mA - 2,000 mA
... high speed high voltage amplifier AMP series is an ultra high speed high voltage amplifier. It realized as fast as 700 V/µs even with load, and approximately 2 times faster than existing models. With ...
Voltage: 10 V
... 4mA, 100µA DC, ±2.5V DC, or 2V eff at 5kHz AC for sensor supply - DC or AC decoupled - patent no. 196 52 293 - reusable for other measuring tasks PERFECTLY CONDITIONED. UNIVERSAL. The ...
These transimpedance amplifiers are particularly useful for the measurement of current from photodiodes. The output is a voltage linearly proportional to input current and thus, to input ...
Voltage: 12 V - 30 V
... configurable. Each alarm threshold commands an output relay. Input signal can be retransmitted on the analog output in a Voltage or Current signal, configurable by means of dip-switch on the side of the device. By means ...
Voltage: 10 V - 18 V
... applications: Features Small Size (16 Pin Dual In-Line Package) allows mounting close to the detector. Power required is typically 12 mW. Single power supply voltage. Low noise. Both Pulse Height Analysis ...
Current: 35 A
Power: 131 W
Doble presents F6350 current/voltage amplifiers. Whenever needed, the F6150 can now be converted to set of voltage and current amplifiers. In this operation mode, the ...
Current: 0.1 mA - 10 mA
... Offset Compensation for Input Amplifier and Photodiode Dark Current RoHS Compliant The PDA200C Photodiode Amplifier is ideally suited for ultra low noise amplification of very small ...
Voltage: 15 V - 30 V
Frequency: 100 Hz
... mm Connection Cable, 2.00 m, PUR Switching output PNP/NPN NO/NC programmable Analog output Analog, voltage/Analog, current 0…10 V/4…20 mA Housing material PBT Ambient temperature -10...70 °C Approval/Conformity CE UKCA cULus WEEE IP ...
Voltage: 220 V - 750 V
Current: 1 A - 11 A
Frequency: 40 Hz - 100,000 Hz
The 5725A Amplifier enhances the 5700A Series Multifunction Calibrators in the ac voltage, ac current, and dc current functions. The ...
Voltage: 10 V - 48 V
Current: 0 A - 2 A
Proportional amplifiers actuate proportional solenoid valves by converting an input signal into a corresponding control current. The proportional amplifier type EV is available as ...
Voltage: 10 V
Current: 0 mA
Power: 0 W - 2 W
... VDC of maximum high voltage power in positive, negative, or bipolar polarity configurations. From a 24 VDC input, HVA models deliver up to 2 W of dynamic power. Across the full operation range, HVA models source and sink ...
Current: 4,000 A
Power Amplifier SM-PA series power amplifier is composed of power exchange unit, electric control unit, signal modulation and protection unit, driving ...
Power: 5,000 W
... unit for up to 15 kA current injection The slave Raptor is visually identical to the master unit but lacks the amplifier, the handheld controller and the auxiliary input/output panels. Its mission ...
Power amplifiers, Voltage and Current Channels of the Mentor 12 The MENTOR 12 is a modular system that offers many possible configurations from typical 3V3I to the maximum of 6V6I ...
Voltage: 12 V - 24 V
Current: 60 mA
... overload protection; Features:Optional transmit power and optional output delay; PC+ABS housing material; 2m PVC cable connection type; FD2 series is CE and EAC approved. Description Lanbao fiber amplifier ...
Frequency: 2 Hz - 20,000 Hz
• Designed with state-of-the-art MOSFET transistors • Sine output power up to 1200 VA • Selectable operation in current or voltage mode • Backgroundlit multifunctional display • Safety management ...
Voltage: 0 mV - 150 mV
Current: 4 mA - 20 mA
... Terminals Fixed or Calibrated Gain 5 years warranty AMPBOX Amplifier AMPBOX is a current loop amplifier for the complete range of solar radiometers. Most radiometers have no power ...
The PIB24L165 is a scalable driver board which, for an input of 0 to 10V (or 0 to 20mA), generates a proportional output current of 0 to 165mA. By shorting out jumper JP1 (shorting header not supplied), the control will ...
Voltage: 8 V - 35 V
Current: 2.6 A
Frequency: 140 Hz
The amplifiers can be used both in mobile applications as well as in stationary installations. The voltage range is therefore very broad and varies between 8 and 35 V DC. These amplifiers are very insensitive ...
WEBER-HYDRAULIK GMBH
Voltage: 110 V - 240 V
Current: 4 A
Power: 11 W
... Description The 1-channel switching amplifier AN001 is used for the current supply and signal evaluation of sensors. It has a 24V DC / 300 mA output, DIN rail mounting and is short-circuit ...
Current: 50 A
The CGS-MV_I card is a precision DC measurement amplifier module (limited AC measurement). It is designed to measure, depending on the shunt resistor, up to 50 A continuously. The typical ...
Please specify:
Help us improve:
remaining