Mechanical testers

LTWTC-203H This product is based on the test principle of gravimetric water vapor transmission, and provides a wide range and high efficiency water vapor transmission rate detection test for low, medium and high water vapor barrier materials. ...

... driven equipment test system which automatically generates a condition assessment report indicating existing electrical mechanical and operational faults, time to failure information, recommended corrective actions, ...

IR-628 Infrared Photosensitive Automatic Tester IR628 is used to measure the absolute photoelectric sensitivity and the receiving angle of the photosensitive tube, and can draw the relative sensitivity distribution ...

Pull / Push Adhesion, Electronic Adhesion Tester KN-10 Equipment developed to measure the adhesion of paint films, coatings and building materials on top of any substrate. The pull-out adhesion test determines the ...

... acceleration. It’s suitable for low-frequency vibration testing of specimen includes electronic components, components, mechanical and electrical products, instrumentation, electronic toys, medicine and food packaging ...

Big Sine Force Vibration Test Systems For Automobiles Vibration Testing Applicable Standards: MIL-STD, DIN, ISO, ASTM, IEC, ISTA, GB, GJB, JIS, BS etc. Applications: Automotive parts and systems - qualification testing ...

It is suitable for bending resistance test on headphone cable.USB cable,multicore cable conductor,flat cable and signal line,etc.The test method is as follows:Firstly,clamp one end of the wire rod and fasten it to the rotation clamp. ...

The 266 S by Erichsen is a cylindrical mandrel bending tester which is designed for testing the flexibility and the adhesive properties of coatings. This is tested through a series bending within a tested component. It ...

... Capabilities • MUT Performance during Acceleration & Deceleration • Analysis of MUT’s full dynamic capabilities, without any mechanical load • Simulation of acceleration under load/inertial conditions • Full load ...

... → GB/T18042 Thermoplastic plastic pipes creep ratio test method → GB/T14452 Metallic materials-Determination of bending mechanical properties → GB/T18477.1 Unplasticized polyvinyl chloride (PVC-U) structure wall pipline ...

Universal Surface Tester with high local resolution for deformation, damping, topograpy, microfriction and many more Universal Surface Solution within One System UST® is designed to deliver quantitative mechanical ...

The SAFT instrument is used to test hot-fail temperature in shear of hot melt adhesives. Weights are attached to the shear samples and the temperature is increased with a controlled rate until the samples fail. The ES 07 can test 6 samples ...

... the eddy current sensors will be influenced by deviations from the ideal circular geometry of the respective rotor plane (mechanical runout) and by residual magnetism and variations of the shaft material properties (electrical ...

FT and FT-Touch look similar to the CT, also operated by hand-lever. FT-Touch features a modern TFT-touchscreen with led backlight. FTS as a variant with a crank. /li> Measuring frequency is 10,000 Hz for all models. ...

The Digital Ink Rub Tester is designed to measure scuffing or rubbing resistance. Several tests can be performed including dry rub-the amount of transfer ink from one dry surface to another, wet rub-the amount of transfer ...

The James Bond Tester™ MK III or pull off adhesion test measures the bond strength or tensile strength of concrete, asphalt, tile, concrete repair, or other overlay material by the direct tension or pull off method. By ...

... cleaned surface. This disc is grab by the pull tester using a female slotted adpator which stays at the base of the pull tester. Then the disc is pulled off in direct tension usijng the hand crank of ...

The burst pressure tester for pipes with large diameters is a further mile-stone for burst tests on large test samples. The frequency-controlled pump units can be combined in a number of ways to enable fl ow rates of ...

Pull-off Adhesion Testers Measures adhesion of coatings to metal, wood, concrete and other rigid substrates. • - Select from four Stand-offs - 20 mm, 50 mm, 50x50 mm Tile and 50 mm C1583 • - Environmentally sealed ...

Multimeters are capable of measuring a number of variables. Each instrument can measure voltage and resistance, as well as performing continuity and diode testing as standard. In addition, the individual multimeters also feature extra ...

... Pressure test radiator and cooling systems of most cars and light trucks for leaks with the four most common adaptors included • Tester achieves the required 35 PSI with fewer pump strokes • New comfortable soft grip ...