Voltage: 24 V - 230 V
... The purpose of the isolating amplifier Theta 60I is to electrically insolate input and output signals, respectively to amplify and / or change the signal level or type (current or voltage) of the input ...
... Mango is a unique platform of optical parametric amplifier built to conform to the highest quality standards. This system can deliver any wavelength from 210 nm to 11,000 nm from the same output port with the same polarization for ultimate ...
Voltage: 24 V
Current: 500 mA
... The Piezo Signal Amplifier PSA4 is a digital 4-channel charge amplifier with integrated EtherCAT fieldbus interface for measuring force, tonnage, pressure, acceleration, vibration and torsion using piezoelectric ...
Voltage: 12 V - 24 V
Current: 0 mA - 50 mA
Frequency: 250, 1,500 Hz
... Wavelength - 623 nm Transmitted- signal shape - Pulsed Short circuit protected Fiber optic connection - Clamp Supply voltage UB - 12 ... 24 V, DC Residual ripple - 0 ... 10 %, From UB Open-circuit current - 0 ... 50 mA Voltage ...
... Ampli Light & Sound System Together with the instruments of quality control, we provide systems of signal amplification in order to make it easier for the operator the management of non-compliance. With these systems it is possible, ...
... ratio · Broad frequency response DC to 10 k Hz (913C) Features The DPM-900 Series is a Dynamic Strain Amplifier. The carrier-wave amplifier features highly accurate, excellent stable, and easy setting. ...
Kyowa Electronic Instruments Co.
... gauge amplifier with up to 8 measuring channels • - Connecting with different kind of strain gauge sensors • - Complete system solutions through networking of devices via CANopen Applications • - Universal usable digital strain gauge ...
Voltage: 9 V - 30 V
... The digital Load Cell Amplifier in junction box DBB is a combination of cable box and an analog-to-digital converter. The internal high-precision digital amplifier with 24-bit A/D converter converts the output signals ...
Bosche GmbH & Co. KG
Power: 1 W
... DT-730: DVB-T 30 dBm Power amplifier (1 W) The DT-730 is a high quality 1 W RF power amplifier for COFDM signals, both for single carrier or multicarrier system. The system provides an amplified output ...
Frequency: 0.05 MHz - 500 MHz
... The AP-0.5GZ23 amplifier is a low-noise, wide bandwidth amplifier that can be used with the RFC-101 series RF Current Probes. 2.0 Key Features • High gain and low noise • Wide bandwidth • Standard 50 Ohm input ...
Voltage: 12 V - 24 V
Current: 60 mA
... Lanbao fiber amplifier and optical fibers; Built-in high-speed digital processing chip; Rich functions, easy to set up, and widely used in various applications; NPN and PNP, depends on different part numbers; 12- 24VDC; 4-digit LED digital ...
Voltage: 24 V
Current: 4 mA - 20 mA
... features wide amplification range (gain from 20 to 5,000) and the capability to amplify either strain gage signal 2mV/V or semiconductor gage signal 50 mV/V. •Input voltage: 24 AC/DC •Output voltage: 0 to 10 DC (4 ...
Voltage: 12 V - 24 V
Current: 100, 50 mA
Frequency: 10 Hz - 55 Hz
... Control output The load voltage is below 24V DC, and the load current is below 100mA. NPN open set electric output type (nesidual voltage below 1V) When light in ON /when light out ON, switching mode Automatic on time opération funclon Delay OFF, ...
Voltage: 0 V - 10 V
Current: 4 mA - 20 mA
... designed to amplify a signal to equipment with current loop 4-20mA or 0-10V. For 35mm DIN rail. Features: Range of operation temperature Min:-10ºC / Max: +40ºC. Power supply: 24VDC. Range of input signal: 0 – 30 ...
Ascell Sensor,S.L.
Voltage: 110 V - 200 V
Frequency: 0 Hz - 20,000 Hz
... All DynaLabs vibration shakers come included with an amplifier out of the box. PM-20, PM-100, MS-20 and MS-100 shakers have integrated amplifiers. With this integrated amplifier it is very easy to ...
Voltage: 100 V - 1,200 V
Frequency: 2 Hz - 20,000 Hz
... Backgroundlit multifunctional display • Safety management system monitors temperature, overcurrent, clipping and overtravel • High Signal to noise ratio of >90 dB • Low distortion factor <0.1% • Selectable operation voltage range ...
Voltage: 30 V
... Waveform Amplifier 30 volts pk-pk • Extends the output range of function generators • 30 Volts peak to peak output swing • DC to 1MHz bandwidth • High impedance input, 0dB to +20dB gain • 50 Ohm and 600 Ohm ...
Voltage: 250 V
Current: 1 A
... Galvanic Isolation Simple USB Configuration Port The SEM1630 is a DIN rail mounted trip amplifier which accepts RTD, Thermocouple, mV and passive current signals and provides a dual trip output. Isolation is provided ...
... total energy output, meeting the requirements of dual energy range experimental setups, avoiding the split of the signal on two shaping amplifiers. ...
Power: 6 W
Frequency: 2 MHz
... Laser light with variable wavelengths are available via optical parametric amplifiers. The AVUS Optical Parametric Amplifier (OPA) provides widely tunable high-energy pulses. It is ideal for use with 1 μm femtosecond ...
Power: 60 W
... ERBIUM-DOPED FIBER AMPLIFIER (EDFA) Neptec’s Erbium-doped fiber amplifier (EDFA) modules are designed for optical network signal amplification and long term reliability. Neptec’s EFDA and Polarization ...
neptec optical solutions
Voltage: 0 V - 10 V
Current: 0 mA - 1 mA
... millivolt-level transducer output signals to a 0-to-10 Volt DC signal proportional to tension and a 0-to-1mA signal proportional to tension. Using an iAMP2™ module is a simple alternative to mounting ...
... features TDP is a digital measuring amplifier for strain gauges bridge, including a 24 bit acquisition circuit with programmable gain .Through the Profinet I/O interface it is possible to program all operational parameters of the unit: ...
Celmi
Voltage: 5 mV
Current: 59 mA
... Portable strain gauge amplifier and display About the TR150 Strain Gauge Amplifiers The TR150 is a completely portable, precision instrument packaged in a small, robust IP65 (NEMA 4) enclosure, weighing only 260 grams. ...
Althen sensors
Frequency: 90 Hz - 520 Hz
... The isolation amplifier Transcont TVA-120-U0 is used for galvanic isolation or for conversion of a signal into another signal. The integrated sensor supply allows the direct connection and by this the ...
ACS Control-System GmbH
Voltage: 50, 2 mV
Current: 4 mA - 20 mA
... features wide amplification range (gain from 20 to 5,000) and the capability to amplify either strain gage signal 2mV/V or semiconductor gage signal 50 mV/V. ...
the best suppliers