OverviewThe YG semi-automatic egg tray machine converts waste paper into molded pulp trays via pulping, forming and drying. It is designed for small to mid-scale producers seeking higher output than manual systems while avoiding the investment of fully automatic lines. Pulping and forming are automated; transfer and stacking usually require manual or assisted labour. Compatible with common drying methods (sun, brick kiln, multi-layer dryers).
Who needs this machineSmall or growing egg-tray manufacturers, local egg farms and packaging distributors needing consistent molded-pulp trays with moderate labour and capital expenditure.
Key differences vs other systems- Manual machine: high labour input, low capital cost, limited output.
- Semi-automatic (this product): moderate labour, mid-level cost, typical output 1,500–7,000 pcs/h depending on model.
- Fully automatic machine: low labour requirement, higher capital cost, continuous high output suitable for large-scale operations.
Production & operating notesMatch forming capacity with drying capacity to avoid bottlenecks. Semi-automatic lines commonly run 8–16 hours/day; continuous 24/7 use increases wear and often indicates the need for a fully automatic line. Plan for water handling, drainage and local power compatibility.
Raw material guidance- Recommended: old corrugated cardboard (OCC) for rigidity; kraft paper for strength and appearance; office/A4 paper for smoother surface.
- Use with caution: newsprint (shorter fibres), mixed recovered paper — perform local pulping tests before full adoption.
- Avoid: wax-coated, plastic-contaminated, or mouldy/wet paper.
- Pulp ratio guideline: commonly ~1 part paper to 3–4 parts water in initial pulping; higher water increases drying energy and time.
Drying methods compatible with semi automatic systems- Natural sun drying: lowest equipment cost, weather-dependent, requires large rack area and labour.
- Brick kiln drying room: heated room method, weather-independent, trays dried on carts under controlled heat.
- Multi-layer metal dryer: stacked heated channels (e.g., 6-layer) for consistent moisture control and reduced labour; higher initial cost.
Common buyer mistakes- Comparing only forming-unit prices while excluding pulping system, dryer and auxiliaries.
- Overlooking local electrical standards (voltage/frequency) and site requirements.
- Assuming all recovered paper mixes perform equally — always test locally.
- Underestimating water consumption, drainage and drying capacity.
- Neglecting mold specifications — mold determines cell count and market compatibility.
FAQ (selected)- Can a semi-automatic machine run 24/7? — Typically operated in shifts; continuous 24/7 use accelerates wear and often warrants a fully automatic solution.
- How long to change molds? — Approximately 2–4 hours with trained staff for alignment and checks.
- Delivery time for standard models? — Standard models usually ship in about 30–45 days after order confirmation; custom molds add lead time.
- Training required? — Basic operation can be learned in 2–3 days; advanced maintenance requires further training.
- Can it produce other molded pulp products? — Yes. With appropriate molds it can make egg cartons, fruit trays and similar items (thicker products may need longer drying).
YG Semi Automatic Egg Tray Machine - Standard Models (summary)YG-1500 – 4X1 | 1500 pcs/h | 38 kW | 120 kg paper/h | 240 kg water/h
YG-2500 – 3X4 | 2500 pcs/h | 55 kW | 200 kg paper/h | 400 kg water/h
YG-3000 – 4X4 | 3000 pcs/h | 60 kW | 240 kg paper/h | 480 kg water/h
YG-4000 – 4X8 | 4000 pcs/h | 95 kW | 320 kg paper/h | 640 kg water/h
YG-5000 – 5X8 | 5000 pcs/h | 95 kW | 400 kg paper/h | 800 kg water/h
YG-7000 – 6X8 | 7000 pcs/h | 120 kW | 480 kg paper/h | 960 kg water/h
Technical specifications (summary)- Product type: Semi-automatic molded pulp egg tray line (pulping, forming + manual/assisted transfer & stacking).
- Capacities available: 1,500; 2,500; 3,000; 4,000; 5,000; 7,000 pcs/h.
- Typical power requirements: 38 kW up to 120 kW depending on model.
- Typical paper consumption: ~120 kg/h up to ~480 kg/h by model.
- Typical water consumption: ~240 kg/h up to ~960 kg/h by model.
- Drying options: sun drying, brick kiln drying rooms, multi-layer metal dryers.
- Mold flexibility: interchangeable molds for different cell counts (e.g., 30-cell, 20-cell, 12-cell) and product types; changeover requires alignment checks and qualified staff.
- Shipment/testing: factory test and test report provided; lead times vary with model and mold customization.