Frequency tester

radiocommunicationwireless communication signalbattery

Overview
Accessories for industrial radio remote controls, including monitor testers, anemometers (WIND DIN 2), wireless battery chargers (standard and compact), protective pouches and antennas (UHF, FLAT 870 and WHIP). Original REMdevice accessories for enhanced operation and reliability of radio remote controls.

Monitor Tester
Self-powered display device to be connected to the receiver, designed to read the remote control’s operating data. Supplied complete with 9V battery and connecting cable.

Information displayed

• Working frequency and channel used
• Signal and interference levels
• Number of starts and total hours of operation
• Number of up and down commands
• Number of other commands (T series)
• Relay operation diagnostics
• Active commands

Anemometers (WIND DIN 2)
Omnidirectional digital anemometer for wind-speed measurement, designed for installation on lifting equipment. Available in km/h and mph versions with clear numeric display.

Key features

• 3-cup sensor with vertical rotation axis
• Stainless steel shaft and bearings
• Two programmable alarm thresholds (factory: 50 km/h & 72 km/h; 31 mph & 45 mph for mph version)

Technical specifications (WIND DIN 2)

• Measuring range: 0–99 km/h (0–99 mph)
• Display: 2-digit numeric
• Power supply: 48 Vac
• Enclosure: Modulbox for DIN EN 50022 rail mounting
• Protection grade: IP20
• Dimensions: 70 × 75 × 90 mm (W×H×D)
• Weight: 350 g
• Wind sensor dimensions: 120 × 80 mm (W×H)
• Wind sensor weight: 140 g

Wireless Battery Charger
Patented wireless charging system that removes electrical contacts to increase operator safety and reduce failures caused by dust and moisture. Fully recharges transmitter internal batteries in approximately 5 hours; a 30-minute temporary charge provides sufficient energy for a full working day. Integrated microchip regulates energy delivery for optimal battery efficiency. Compatible with multiple REMdevice transmitter families (Brick, Pail, Genesis).

Technical specifications (standard wireless charger)

• Oscillator with automatic current control
• Supply voltage: 230 Vac (115 Vac version available for American market)
• Current demand: 0.1 A
• Housing protection rating: IP55 – material PA6 GF V0
• Dimensions: 135 × 85 × 190 mm (W×H×D)
• Weight: 790 g (complete with mains cable and A-type USB plug)

Compact charger version
Same performance and features as the standard model in a compact format suitable for vans, trucks and PC USB sockets.

Technical specifications (compact charger)

• Dimensions: 95 × 15 × 120 mm (W×H×D)
• Weight: 120 g (complete with mains cable and A-type USB plug)

Protective pouches
Available with or without belt for Brick and T Series transmitters. Multiple pouch configurations and finishing options to fit different transmitter families.

Antennas
Three antenna families available (model depends on working frequency): UHF, FLAT 870 (panel) and WHIP. Robust, waterproof designs for industrial applications; delivered with cable and connector variants depending on model.

UHF antenna

• Working frequencies: 418 MHz, 433–434 MHz, 870 MHz, 915 MHz
• Gain: 5 dB
• Housing protection rating: IP65, material PA6 FV
• Dimensions: 128 × 72 × 50 mm (W×H×D)
• Weight: 140 g
• Supplied with standard 1.5 m cable and SMA or SMB connector (depending on model)

FLAT 870 (panel antenna)
Panel antenna using microstrip technology to improve directivity and signal-to-noise ratio where the signal must pass around obstacles.

Technical specifications (FLAT 870)

• Configuration: panel
• Working frequency: 863.000 – 870.000 MHz
• Gain: 14 dB
• Dimensions: 240 × 25 × 240 mm (W×H×D)
• Weight: 800 g
• Supplied with standard 3 m cable and SMA connector

WHIP antenna
Designed for installations where the signal must circumvent shielding obstacles; supplied ready for mounting on a pole or equivalent support.

Technical specifications (WHIP)

• Working frequency: 418 MHz, 433–434 MHz, 870 MHz, 915 MHz
• Gain: 8 dB
• Dimensions: 35 × 450 × 35 mm (L×H×D)
• Weight: 310 g
• Supplied with standard 3 m cable and SMA connector

Images and gallery
Multiple product images and galleries available for accessories: monitor tester, anemometers, chargers, protective pouches and antennas.

Specifications

• Monitor tester: self-powered, includes 9V battery and connecting cable; displays frequency, channel, signal/interference levels, counters and relay diagnostics
• Anemometer WIND DIN 2: range 0–99 km/h, 2-digit display, 48 Vac supply, DIN-rail enclosure, IP20
• Wireless charger (standard): 230 Vac supply (115 Vac version available), 0.1 A current demand, IP55 PA6 GF V0 housing, dims 135×85×190 mm, weight 790 g, full recharge ~5 h, 30 min temporary charge for a work day
• Compact charger: dims 95×15×120 mm, weight 120 g
• UHF antenna: frequencies 418 / 433–434 / 870 / 915 MHz, gain 5 dB, IP65, dims 128×72×50 mm, weight 140 g
• FLAT 870 antenna: frequency 863–870 MHz, gain 14 dB, dims 240×25×240 mm, weight 800 g
• WHIP antenna: frequencies 418 / 433–434 / 870 / 915 MHz, gain 8 dB, dims 35×450×35 mm, weight 310 g
• Protective pouches: available with or without belt for multiple transmitter families