|
|
|
The desanders are designed for treating and straining bentonite slurry used in foundation works. The centrifugal hydrocyclone and the vibroscreen separate solid particles during the bentonite mud recovery process.
|
|
The mixer is suitable to mix water and bentonite. The equipment is powered by electric motor or diesel engine that give the movement to a centrifugal pump which mixes the fluid.
The mixer is equipped with manual flow diverters.
|
|
The range of agitators, mixers or mixing units has been designed for all types of job sites. The MR, MA, TMD or UF sets are robust, reliable and simple to use and maintain.
Use
They are generally used for the fabrication of the mud or the slurry of job sites of foundation, ground treatment, of ground consolidation, of sewer or tunnel restoring, or of micro-piles.
Versatility
Fully fluted and laid, manual or automatic with weight reports, the mixers MR, MA, TMD, UF are quickly transported and erected on a job site.
Performance
The mixers cover a large range of mud or slurry fabrication (from 400 gal/h to 6 600 gal/h) adapted to all types of job sites.
Safety
The mixers are equipped with protection covers and an emergency stop at the work
station.
|
|
|
|
|
|
|
GM-20A Drill, a light weight big-hole engineering drill, is im0proved and designed based on GM-20 drill. The new type drill unites the tower and machine body. This type of drill integrates the drill's advantages of the type's turn plates, the power heads and the main shaft drills. The drill has such advantages as high drilling efficiency and precision, powerful torque, wider ranges of speed and smaller coefficient of oversize of hole. It can drill in the ways of forcing feed or reducing bit load drilling by hydraulic system. Oil cylinders of the drill can raise or pull down the tower safely and quickly, move and fit the hole position conveniently. After moving the machine, the bit of two meter diameter can be directly lifted or run in. height of the tower is ten and five meters, which can directly pull down the steel cages. The assistant hoist's capacity is strong. The drill is equipped with step device as to fitting the hole position conveniently. The control handlebars are collected so easy to operating. The drill can be used in the drilling technologies of normal or reverse circulation in the quaternary period gravel or hand rock ground. The drill can be mainly used for big-hole grouting pole holes drilling of high building, port and bridge.
|
|
|
|
|
|
Downhole drilling rig Introduction
The integrated hydraulic downhole drilling rig is widely used in metallurgical, mining, building materials, railway, hydropower construction, national defense construction and earth works, and the blasting hole drilling of open construction. It takes hydraulic drive for track traveling, rotary drill tool forward, drill tower top lifting compensation and drilling rig leveling. It takes compressed air from screw-type air compressors to impact drilling and flush the hole, with air pressure range of 1.05-1.4 M Pa, and dry-type distribution laminar precipitator. The drilling tool takes Ingersoll-Rand high-pressure downhole impactor, with the drilling aperture of 90 ~ 180 mm, and the depth of 30 m vertical or inclined hole. It is the most advanced integrated hydraulic downhole drilling rig in China, with the feature of highly-efficient high pressure downhole drilling system, which facilitate to drill the blasted hole with high-precision and high efficiency. Global purchase, optimal design with the computer, power matching and the development and application of load applicable system contribute to the realization of the overall power load matching from power-pump -load in the power system, which effectively reduces the overall energy consumption and ensures the best performance and the overall high reliability.
|
|
Terex® SKF Rotary Blasthole Drills
The SKF crawler-mounted blasthole drills are designed to drill from 6" to 10 5/8" (152-270 mm) diameter holes with rated pulldown and hoist capacity up to 50,000 lbs. (22,680 kg) and 47,100 lbs. (21,364 kg) respectively, in rotary or down-the-hole applications. 60,000 lbs. (27,216 kg) pulldown optional.
SPECIFICATIONS SKF ROTARY BLASTHOLE DRILL
Hole diameter 6" - 10 5/8" (152-270 mm)
Total hole depth Single-pass 33.2' (10.1 m); Multi-pass 173' (52.7 m)
Rated pulldown capacity Up to 60,000 lbs (27,216 kg)
Power unit Caterpillar, Cummins
Compressor Up to 1,700 cfm @ 100 psi
Compressor Option Up to 1,500 cfm @ 350 psi
|
|
|
Atlas Copco can offer the most comprehensive line of rotary blasthole drills in the industry. With a multitude of configurations to choose from you can find the perfect solution for your needs. Our blasthole products can meet your demands from 4" up to 16" hole diameter, and many models can be configured either for rotary or DTH drilling.
|
|
The Eagle 4500 & 5500 are high production, low maintenance Bucket Wheel Trenchers. The Eagle Foundation Trenchers are the most cost effective way to increase profitability. The trencher digging wheel is mechanically driven for the maximum transfer of horsepower, all other machine functions are hydraulic. All controls are well marked and positioned for ease of operation and optimum operator visibility. G&Z is committed to producing high production, low maintenance trenchers. Eagle Trenchers are the most cost effective way to increase the profitability of your job. The Eagle 4500 and 5500 are excellent choices for a wide variety of applications, such as foundations, utilities, irrigation and fiber optic installations in friable soils.
Key Features
- Hydraulic Crumb Shoe
- Hydraulic Wheel Lift and Tilt
- Bridge Type Boom Frame
- Dozer Blade with Stake Pockets
- Berm Scrapers
- Roll Over Protection Structure (ROPS) Not shown in photos
- Back-Up Alarm
|
|
|
|
|
|
Cable Burster, EXTRACTOR
The TERRA-EXTRACTOR X 400 is a cable burster (wire burster) which replaces old pipes from 1 1/2“ (ID 40 mm) up to 10“ (ID 250 mm). Lengths up to 150 m are possible. Old pipe from cast iron, steel, clayware or PE/PVC can be replaced. New HDPE pipes with outer diameters of 63 – 250 mm are pulled in. The TERRA-EXTRACTOR X 400 is operated via an electric remote control. No operator has to be in the pit or in the manhole during operation. An integrated electric control box changes the direction of the hydraulic cylinder.
The standard version of the TERRA-EXTRACTOR X 400 requires a working pit, which is only 1.70 m long and 1.00 m wide. In spite of this small working pit, the X 400 pulls the bursting tools and the new pipe into its front box and into the working pit, after the pipe renewal job has been finished. This is fast and efficient.
The TERRA-EXTRACTOR X 400 operates at speeds up to 145 m/h. It is equipped with a pulling force of 400 kN (40 tons) which adapts itself automatically to the real working conditions. The TERRA-EXTRACTOR X 400 is powered by a supersilent Diesel power pack which has been designed exactly for this wire burster. As an option remote pressure control is available.
|
|
C800DH - Technical Data
- Max depth: 34 m
- Max diameter: 1600 mm
- Engine power: 400 kW
- Width of crawler: 3500 ÷ 5000 mm
- Shoes width: 1000 mm
- Torque: 358 / 421 kNm
- Drilling speed: 25 / 18 rpm
- Weight in working condition: 130000 Kg
|
|
CFA425 - Technical Data
- Max depth: 25 m
- Max diameter: 900 mm
- Engine power: 214 kW
- Width of crawler: 2500 ÷ 4000 mm
- Shoes width: 700 mm
- Torque: 112 kNm
- Drilling speed: 33 rpm
- Weight in working condition: 42000 kg
|
|
CFA Rotary Rigs
Self erecting hydraulic powered equipment mounted on SOILMEC crawler unit. A number of conversion kits allows the execution of: driven and cast-in-situ piles, prefabricated driven piles, vibrated driven piles, bored piles in rock, drains, continuous flight auger.
|
|
|
|
|
|
The QXR is a track drill with a boom-mounted feed system that drills with a pneumatic DTH hammer.
The QXR 920 drills at sea level from 4 in (101 mm) to 6-1/2 in. (165 mm) diameter holes with a DTH Hammer to a depth of 140 ft. (42.7 m) without reloading the carousel and to greater depth with reloading. The drill is designed to flexibly switch between Production Drilling, Pre-Split or Pre-Shear drilling and with options Reverse Circulation sample drilling.
The QXR 1120 can be used to drill 4 in. to 8 in. (101 mm to 203 mm) holes with a DTH hammer, to a depth of 140 ft. (42.7 m) without reloading the carousel and to greater depth with reloading the carousel. The drill is designed to flexibly switch between Production Drilling, Pre-Split or Pre-Shear drilling and Reverse Circulation sample drilling.
The QXR 1320 can be used to drill 4 in. to 10 in. (101 mm to 255 mm) holes with a DTH hammer, to a depth of 140 ft. (42.7 m) without reloading the carousel and to greater depth with reloading the carousel. The drill is designed to flexibly switch between Production Drilling, Pre-Split or Pre-Shear drilling and Reverse Circulation sample drilling.
|
|
The King of all large diameter hole drilling machines.
Great turning ability in narrow bench,comfortable cabin.Easy to operate.
Advanced drilling system,high pressure high blow compressor,
and high power engine work hard for you at the job-site.
|
|
|
Atlas Copco's range of surface crawlers raises the quality of rock drilling to a new level. The lowest cost per tonne of rock produced comes from the higher productivity; straighter holes and better overall economy are designed into the range. These surface crawlers include several models that are ideally suited for bench drilling. Choose between hydraulic top-hammer, Atlas Copco's patented COPROD system, or down-the-hole drilling methods. The unique SmartRig will help you to drill smarter holes with high shift capacity, low energy consumption, and innovative modules that improve productivity. Atlas Copco's range of crawlers is setting new standards for stability, maneuverability and safety in quarries and contracting work.
|
|
Apafor 440 and 450
Powerful and versatile drilling rigs able to perform all kind of coring, rotary and rotary-percussion dring operations.
Large speed and torque range thanks to the variable volumetric displacement hydraulic motor.
Fully self-sufficient version at disposal with its injection pump fitting.
DEUTZ diesel engine (440) or HATZ diesel engine (450).
Available with reinforced torque, especially for micro-piling (450MP).
Various technical adaptations possible and numerous options available.
|
|
The fully hydraulic TM 255 crawler drill rig has been developed as a down the hole hammer drill rig for small and medium-sized quarries and drilling companies.
This rig is designed for drill-hole diameters from 92-130 mm and for drill-hole depths up to 32 m.
The TM 255 is a fully hydraulic crawler drill rig with a telescopic boom featuring 360° rotation, carriage with revolver magazine, a powerful down the hole hammer and dust collector.
The undercarriage consists of a frame with crawler undercarriage, the corresponding components and body work and a comfortable FOPS-ROPS cabin. The drill is powered by a diesel engine via hydraulic motors and wheel hub drives.
|
|
The fully hydraulic TM105A crawler drill rig has been developed for use in many areas of the construction industry. It is used for disaggregation in quarries, forest road building, slope reinforcement drilling, drilling for blasting, trench drilling, etc.
The TM 105A is a fully hydraulic crawler drill rig with a articulated boom, carriage, hydraulic hammer and dust collector.
The undercarriage consists of a frame with crawler oscillation and corresponding components and bodywork.
The drill is powered by a diesel engine over hydraulic motors and wheel hub drives.
|
|
M3 E/D - Technical Data
- Engine power: 55/45 kW
- Width of crawler: 850/1200 mm
Mast:
- Stroke of rotary head: 700 mm
- Extraction force: 3000 kg
- Crowd force: 3000 kg
Clamps:
- Diameters: 40 ÷ 254 mm
Rotary head:
- Torque: 8,2 kNm
- Speed range: 330 rpm
Weight:
- in working condition: 5740 kg
|
|
C14 - Technical Data
- Engine power: 165 kW
- Width of crawler: 2530 mm
Mast:
- Stroke of rotary head: 12000 mm
- Extraction force: 140 kN
- Crowd force: 140 kN
Clamps:
- Diameters: 90 ÷ 406 mm
Rotary head:
- Torque: 17900 Nm
- Speed range: 223 rpm
|
|
SD 710
* DESCRIPTION
The SD 710 is a track mounted drill with an on board high pressure Booster compressor.
* PERFORMANCE
The SD710 that drills at sea level with a 3 inch, 4 inch or 5 inch DTH Hammer to a depth of 325 ft. (100 m). The drill is designed to flexibly switch between Blasthole Drilling, Grout hole, Pre-Split drilling, Over burden drilling and Reverse Circulation sample drilling.
|
|
Explo 220MPR
Portable drilling machine
Geophysics, geotechnics
Engine: Gasoline 20cv - Weight 325 kg
Available diesel or electric version
Emci proposes to you a range of machine of 18 with 110cv. As a manufacturer, our vast choice of options and equipment for each category of product enable you to choose the adequate drilling machine and to configure it according to your type of activity.
|
|
Emci 300
Drilling machine on chenillard
Engine: Deutz 30cv - Weight 1500kg
Emci proposes to you a range of machine of 18 with 110cv. As a manufacturer, our vast choice of options and equipment for each category of product enable you to choose the adequate drilling machine and to configure it according to your type of activity.
|
|
Optima
Drilling machine on chenillard
Geotechnics, environment, drilling of water
Engine: Deutz 70 cv - Weight 4200 kg
Emci proposes to you a range of machine of 18 with 110cv. As a manufacturer, our vast choice of options and equipment for each category of product enable you to choose the adequate drilling machine and to configure it according to your type of activity.
|
|
Silea
Drilling machine on chenillard
Engine: Hatz 50 cv - Weight 2000 with 2500Kg
Emci proposes to you a range of machine of 18 with 110cv. As a manufacturer, our vast choice of options and equipment for each category of product enable you to choose the adequate drilling machine and to configure it according to your type of activity.
|
|
General-purpose drilling machine Innovated
Drilling machine on chenillard
Engine: Deutz 110cv - Weight 8000kg
Emci proposes to you a range of machine of 18 with 110cv. As a manufacturer, our vast choice of options and equipment for each category of product enable you to choose the adequate drilling machine and to configure it according to your type of activity.
|
|
Emci 230
Light drilling machine on chenillard
Engine: Perkins 23cv - Weight 1150kg
Emci proposes to you a range of machine of 18 with 110cv. As a manufacturer, our vast choice of options and equipment for each category of product enable you to choose the adequate drilling machine and to configure it according to your type of activity.
|
|
The Ultimate combination of performance and economy.
New drifter design with automatic drilling system delivers the highest-possible drilling performance at low running cost..
|
|
HYDRAULIC DRILL RIGS
HBR 609 - Technical Data
- Engine power: 190 kW
- Width of crawler: 2425 mm
Mast:
- Stroke of rotary head: 4950 mm
- Extraction force: 100 kN
- Crowd force: 100 kN
Clamps:
- Diameters: 68 ÷ 254 mm
Rotary head:
- Torque: 6,3 kNm
- Speed range: 80 rpm
Weight:
- in working condition: 21000 kg
|
|
HYDRAULIC DRILL RIGS
HBR 502 - Technical Data
- Engine power: 82 kW
- Width of crawler: 1600 mm
Mast:
- Stroke of rotary head: 3375 mm
- Extraction force: 30 kN
- Crowd force: 30 kN
Clamps:
- Diameters: 27,5 ÷ 143,5 mm
Rotary head:
- Torque: 6,3 kNm
- Speed range: 80 rpm
Weight:
- in working condition: 7900 kg
|
|
|
|
Drilling, Pile driving, Trenching machines
