|
|
Material:
Oval aluminium EN AW-6060
Surface finish:
Black powder-coated, natural colour anodized
Note:
These KIPP Oval Bow Handles are extremely robust and can also be used in any situation where powerful operation is required.
|
|
Aluminium bow-type handles
Made of profiled aluminium, round bar aluminium or chilled casting in different anodizing versions or powder coated. With a big variety of standard-types for 19"-housings.
|
|
|
Innovation 2008 - Galletti of implantation passing, with compass and stud - handle to resumption with compass and stud - pressori to puntale and spring in burnished steel and inox.
|
|
Material: Steel.
Chemical black finish with a black plastic ball knob.
|
|
- Clamping lever for drill jigs
Application:
Any MayTec-connector can be equipped with a clamping lever.
For frequent opening and closing.
- Clamping lever for connector
clamping handle : PA-glass-fiber reinf.
clamping lever : with ratchet lever handle
annular gear : die casted zinc
thread : steel
|
|
LOWER LEVERS
SERIES 100E SERIES 100S
CONTROL LEVERS LA 200 - LV 24 - LV 26 LVS 28 - LV 30
Simple levers in PA66 or white zinc plated and chronium plated levers.
Locked levers with automatic locking or left and right manual locking.
UPPER LEVERS
CONTROL LEVERS DS01 - DS02 - DS03 - DS05 - DS06 - DS07 - DS08
The control can act on a microswitch with electric cable or on a mechanical transmission cable (sheath and wire rope) that allows a cable linear travel. It is largely used as "deadman" lever.
|
|
ADJUSTMENT LEVERS
SERIES AE50 - AE100 - AE200 - AE250 - AE300
The control is composed by a central body in metal and in some series by a plastic piece which a little lever complete with knob rubs against: the knob can be supplied dismounted to facilitate the assembly under bonnets or dasboards.
The device is assembled on a wall by means of two fastening screws.
|
|
Description: Customizable control for automatic transmissions
Transmissions: Sundstrand, Ford
Engine: Construction equipment, hot rods
|
|
ART. E215
CRANK HANDLE WITH THREADED INSERT
AND REVOLVING HANDLE
MATERIAL:
Reinforced polyamide.
Oils and greases resistant.
SURFACE:
Satin.
COLOUR:
Black (RAL 9011).
MAIN INSERT:
Brass blind threaded bush.
(*) Zinc plated steel blind threaded bush.
SIDE INSERT:
Brass right through threaded bush.
SIDE HANDLE:
Revolving handle Art. M144 (see chapter M on page 6).
SPECIAL REQUESTS:
• It is possible to supply the inserts in different
materials, on request and for quantities.
• It is possible to supply arm and handle with colours
as shown in the table at page 15, on request and for
quantities.
|
|
67 - CONCEALED PULLS
- Unique concealed design
- Handle is hidden within enclosure, rotates out for use
- Fully concealed mounting hardware
P1 - FLUSH PULL
- Flush mounted exterior, grip is recessed inside of cabinet
- Provide ample depth for a substantial grip
- Can be used for lifting or pulling
|
|
ART. B221
FIXED HANDLE WITH NUT
MATERIAL:
Reinforced polyamide.
Oils and greases resistant.
SURFACE:
Satin.
COLOUR:
Black (RAL 9011).
MAIN INSERT:
Zinc plated steel nut DIN 934/UNI 5588.
SPECIAL REQUESTS:
• It is possible to supply the nuts with black oxide
treatment, on request and for quantities.
• It is possible to supply colours as shown in the
table at page 19, on request and for quantities.
|
|
Bridge handles
Safety handles
Flush pull handles
Tubular handles
Pull handles
Fixed and revolving handles
Fold-away handles
|
|
Pull Handles
Whatever your application requirements, we have the handle you need. Steel handles for racks and drawers, stainless steel handles for medical or laboratory equipment, aluminum handles for panels and electronic equipment, plastic machine handles, and operating handles for metal cabinets
|
|
|
|
|
|
Front Handle and Lock - Drawer Handles
GSF's front handle and lock mechanism is extensively used on fire truck drawers (straight slide out and slide and tilt). The double handle and push button locking mechanism is located at the centre of the drawer front in order to ensure the operator's gloved hands are kept well away from pinch risks.
The strong aluminium handle enables the operator to exert full control over the movement of what is likely to be a heavy drawer, both when opening and closing, and the locking mechanism can be installed so as to provide a slam-shut lock-in functionality for slide and tilt drawers, as well as a lock-in and lock-out function for conventional straight slide-out drawers when mounted under the drawer pan. The locking mechanism retracts the spring loaded locking bolts, which slot into the slam-shut lock blocks integrally fixed to GSF's award winning slide and tilt front bracket.
The unit is generally supplied without an aluminium drawer front, and at a standard width of 1,500mm. The user would then cut the locking bolts to their own desired width, although the system can be supplied with the locking bolts pre-cut by GSF to the user's specified length.
|
|
Front panel handles, ledge handles and casing feet
For sliding doors, drawers, shelves, 19"-slots or as edge-protection. Casing feet made of plastic or diecasted zinc for high stress and securing against turning down by adjusting.
|
|
No. 4305
This Eberhard Pull Handle offers an attractive appearance plus a substantial grab area for your hand. Material: Zinc Die-Cast Finish: Polished Chrome Weight: .89 lbs.
Eberhard offers a wide range of other size grab handles made out of different materials with differnt finishes, please contact Eberhard for more information on grab handles.
|
|
|
A broad choice in the range of the handles clamps EMILE MAURIN! Dimensions: distance between centres from 86 to 1000 mm Material: cast iron, aluminium, steel, stainless, technopolymère, polyurethane… Form: bent, tubular, off-set, ellipse, widened, punt… Various colours Discover models of handles clamps especially adapted to your constraints: A handle clamp technopolymère with antimicrobic protection which empèche the deposit of the bacteria, mushrooms and mould while ensuring the total cleansing of surfaces. A handle special clamp in technopolymère which makes the handle flexible. It is assembled on curved surfaces having a diameter ranging between 300 and 600 Misters. But also of the handles clamps resistant to high temperatures (200°C), with an oval tube, hollowed out side supports, etc… For all specific demands for handles clamps, consult us…!
|
|
Swing, sliding and lifting doors are operated with handles or grip systems.
The grips are either screwed directly into an inherently stable panel element or they are attached to the profile of the panel frame.
|
|
Material: stainless steel 1.4301 . Polished surface (sandblasted treatment on request).
Applications: pharmaceutical, chemical, food, wine and packaging industry.
|
|
|
|
|
|
with functions:
With mechanical, pneumatical, or electrical function. At the electrical version all connections of buttons, emergency stop and LED will be lead out of the handle, that the customer can use all functions individually.
Aluminium bow-type:
Made of profiled aluminium, round bar aluminium or chilled casting in different anodizing versions or powder coated. With a big variety of standard-types for 19"-housings.
Stainless steel :
For all areas with high corrosive resp. chemical demands as medicine technology, wet areas, chemical installations and the food industry.
Machine and control housing:
Stable aluminium handles with high dimensions for machines and housings in different anodizing versions or powder coated.
Front panel , ledge and casing feet:
For sliding doors, drawers, shelves, 19"-slots or as edge-protection. Casing feet made of plastic or diecasted zinc for high stress and securing against turning down by adjusting.
Clean Line:
A selection of our standard handles in a version for sanitation areas as e.g. medical technology, food industry and hospital equipments.
single elements:
In modern industrial design. Ledge and shanks are made of similar or different materials as aluminium, steel, stainless steel or plastic.
Bow-type of round steel rod:
Bent handles of steel with centrical threaded holes, high glossy chromed, matte chromed or powder coated.
Plastic bow-type:
With high carrying comfort, made of thermo-plastic (glass-ball reinforced polyamide PA6) or highly stressable, heat resistant duroplastic (bakelite).
...
|
|
Japanese manufacturer, Sugatsune, has a wide range of handles and pulls for industrial or furniture applications.
Rust-resistant 316 or 304 Stainless Steel handles
Recessed pulls
Hatch pulls
For more information, please visit our website or view PDF catalogues here.
sugatsune.co.jp (Sugatsune Japan)
sugatsune.com (Sugatsune America)
sugatsune.net (Sugatsune America-Industry)
|
|
|
TriMark handles are developed with "hands on" applications in mind. Handles that are stylish and economically satisfying are trademarks of push button, paddle pull and rotating handles designed and manufactured by TriMark. A wide variety of attractive and functional styles and finishes are available so whatever your requirements. TriMark can deliver.
|
|
Handle Stainless Steel
WDS8549
Material- Handle - Stainless steel BS 970 Gr303S31. Matt gloss finish Screws - Stainless steel Screws and Washers supplied M-Hex Head
|
|
Front Handle
Bridge Handle
Machine Handle 135
Machine Handle 240
Comfort Handle
End Pieces for System Handle
Tubes for System Handle
Customise
|
|
B4 - LIGHTWEIGHT HANDLES
- Lightweight aluminum construction
- Rear-mounting design hides fastener hardware
- Available in multiple sizes to match grip and load requirements
B8 - GRAB HANDLES
- Available in two sizes to satisfy space and strength requirements
- All models provide fully concealed mounting hardware
- Corrosion-resistant materials
|
|
|
Bett Sistemi designs its “Original BETT Sistemi” STANDARD COMPONENTS for application on machines and equipment for the industry. In particular, Bett Sistemi designs, manufactures and markets the B Handles line (handles). As well as forming an integral part of the systems supplied by BETT Sistemi, these products can be adopted on the entire machine because of their functionally and design.
|
|
|
|
Handwheels, Levers, Handles, Maneuvering parts
