|
|
Absolute filtration :
To eliminate dry smoke typical of certain applications where straight oïl is used.
The efficiency level guaranteed is 99.95% MPPS according to EN 1822 (équivalent to H13). Its clogging can be monitored with an optional pressure gauge.
|
|
|
The X-11Q cigarette smoke filter is designed to fit inconspicuously into a drop ceiling, replacing a 2'x4' ceiling tile. The X-11Q filters smoke, dust, pollen and many other irritants with up to 99.8% efficiency without the need to replace filters. Designed with the user in mind, the 3 speed fan found on this air cleaner quietly and efficiently cleans an area using the Coanda airflow pattern.
|
|
|
|
|
|
High efficient activated charcoal adsorption purifier series AKM / AKN
Oil vapour adsorption from compressed air and gases.
Oil aerosols down to a particle size of 0,01 micron can be removed by a ZANDER X grade Microfilter. Modern industry and process plants need compressed air free of oil vapour, which can only be removed effectively by a ZANDER oil vapour adsorber. Design and Operation:The ZANDER AKN activated carbon adsorber is filled with a special grade of activated carbon*1 for the removal of oil vapour from the top to bottom of the vessel. Thanks to an optimum contact time, velocity, bed depth and quality of activated carbon, the remaining oil content is reduced to 0,003 mg/m3. The quality of the air can be monitored by the oil indicator, which is fitted as standard. Experience has shown that a carbon life of 10,000 hours can be achieved, when a ZANDER X grade Microfilter is fitted up-stream. The exact life of the carbon depends on efficiency of the compressor, the type of oil used and the relative humidity of the compressed air.
Capacity from 8 m³/h up to 6100 m³/h, referred to 1 bar and 20° C. Residual oil content: up to 0.003 mg/3. Paint compatible units available!!!
www.zander.de
|
|
CHL Activated-Carbon Filtration Units are made of rugged sheet-metal structures, welded so as to be air-tight. They have been designed for space-saving installation in ventilation ducts, and for wall installation. These units have proved highly appealing to users because the activated-carbon cartridges can be very quickly exchanged.
Special features:
- High degree of separation (owing to long filtration detention times) at low pressure difference
- Use of only washed active carbon
- Ability to exchange the activated-carbon filling of the cartridges
- High degree of operational effectiveness and reliability
- Rugged and stable sheet-metal structure (3 mm)
- Space-saving
- Fast exchange of activated-carbon cartridges
Application:
Filtration of organic gases and vapours, ammonia (NH3), odours, and formaldehyde
|
|
|
|
|
|
Environmental Tobacco Smoke (ETS) air cleaning machine
The ETS –V1 target is Environmental Tobacco, its design has a four stage air purification system:
- Air first enters the disposable pleated pre-filter, which removes coarse dust, lint and fibers, while also prolonging the life of the other particulate filters.
- Afterwards the air enters the v-bag filter capturing the finer dust particles as small as 0.3 microns.
- Then the air flows to the gas filter where the gas contaminants are adsorbed.
- The final filter is a high efficiency HEPA 11 with integral efficiency above 95%
BENEFITS
Highly recommended where dust, smoke and air chemicals are present
Effectively removes irritants, providing a healthier environment for customers and employees
Reduces most of the tobacco and body odors
Reduces maintenance cost, with less dust and color change in walls and furniture
FEATURES
Three stages particles separation system with bacterial filtering capacity.
The most powerful gas purification system in the market, by his wide spectrum and the amount of activated carbon and potassium permanganate pellets.
More than 100,000 cigarettes filtering capacity
SPECIFICATIONS
Materials: Aluminum frame, with stainless steel sandwich panels with 23 mm internal isolation
Dimensions: 2000 x 71,5 (810 with door handle) x 510 mm
Performance: 1350 m3/h with all the filters installed
Motor: 0.370 Kw, 230 v, 1 Ph
|
|
|
For air purification, the XJ-2 is the quietest medical-grade room HEPA air cleaner available that is suitable for hospitals, extended-care facilities, nursing homes and institutional use. This is also a great unit for asthma patient rooms. Optional digital room pressure monitor gives the CDC specified position certification that negative pressure in the isolation room is maintained. The XJ-2 air filtration system is independently lab tested and certified as a whole air cleaner to a minimum of 99.97% efficiency. This is especially important as simply installing a HEPA air filter into an air cleaner cabinet can not guarantee HEPA performance as penetrations into the air cleaner cabinet, leaks around doors and the integrity of the HEPA seal itself must all be taken into consideration and tested to guarantee performance.
|
|
Low Noise, High-Efficiency Cleaning
The Airflow Systems line of high-efficiency air cleaners remove annoying smoke, odors, dust, and dirt from offices, break rooms, cafeterias, and computer rooms. These air cleaning units can be conveniently concealed above ceilings. The non-electrostatic design of these air cleaners eliminates the problem of snapping and popping common with old-fashioned electrostatic models. Washable pre-filters, a primary box filter, and optional HEPA after-filters combine to provide 99.97% filtration efficiency at noise levels as low as 55 dBa.
|
|
The Cyclevent range of mobile adsorbers are designed as a combination of transport vessel and adsorber for air and gas phase applications, principally VOC Removal. This eliminates the requirement for on-site carbon exchange. These units are supplied on a full service (or rental) basis which gives the flexibility for short term problems or as a preliminary system until a dedicated system is installed. Individual units can treat up to 20,000m³/h.
The benefits of the Cyclevent include:
* Simple installation and operation
* Rapid installation
* Low capital expense
|
|
Micro Air's line of commercial air cleaners is designed to control airborne particulate and fumes that are present in commercial facilities. These include cigarette and cigar smoke, paper dust, toner dust, printing odors and solvents, carpet odors or other indoor air pollutants. With options like wall mount, flush ceiling mount, and below or above ceiling we will solve your specific air quality issues.
These Media units utilize a series of filters to collect the particulate. These include pre-filters, media bag filters, HEPA filters, and/or charcoal modules. Micro Air equipment can be configured with various combinations of media to most effectively capture the specific particulate or fume.
|
|
Electrostatic air cleaners and mechanical filters
A highly effective range of mechanical, electrostatic and cartridge filters.
Smoke removal
A two stage electrostatic precipitator, predominantly used for smoke extraction. Contaminated air is drawn into the precipitator where it's screened by a mechanical prefilter removing large particles. The air then passes through a uniquely designed aerofoil ioniser and is subjected to an intense electrostatic field which charges the particles in the airstream. These enter the collecting cell where earthed plates collect the particles.
Fume removal
Mobile mechanical filters are ideally suited for fume removal at various welding workplaces. The mechanical welding smoke filter unit guarantees effective cleaning, with a filter efficiency above 99.9 %.
HSE Regulations
Further information on the following HSE topics can be found through the links below:
L.E.V.
A workers’ pocket guide to LEV
COSHH
|
|
|
|
|
|
MultiMaster Vario Electrostatic Filter E
The large-scale electrostatic filter MultiMaster Vario has a modular design, and is intended for use as an integrative module in ventilation ducts. The electrostatic filter cells are installed in mounting frames made of stainless steel. Installation of the filter elements is next to each other and on top of each other. The MultiMaster Vario Electrostatic Filter sets the standard for advanced electrostatic-filter systems.
Special features:
- High degree of separation, with low differential pressure
- Latest control technology, implemented by circuit boards
- High voltage is automatically controlled to the highest-possible operating point
- Extremely effective and safe in operation
- The purified air has a deodorizing effect on the air-conditioned air
- Can be fitted with a washing system, which minimizes maintenance
- For filtration of problematic oils in process-air engineering, the use of intermediate catch pans is possible
- Insulators made of KER 221
- Possibility of installing pre-filters and post-filters
|
|
BA-2025 and BA-2030
Stationary breathing air purifiers incorporating CO and CO2 removal.
HPBAP Series
High pressure breathing air purifiers incorporating CO and CO2 removal.
Regenerative NBC Filtration for Fixed and Mobile COLPRO Facilities
Modularity and capacity to be integrated into virtually all COLPRO facilities from citadels to complete buildings.
BA-2006
Medium pressure breathing air purifier without CO or CO2 removal.
BA-DME and BAM Series
domnick hunter provide a comprehensive range of breathing and medical air purification systems for use with Respiratory Protection Equipment (RPE) and in medical applications.
|
|
|
BAUER KOMPRESSOREN is recognised as an international leader in the field of high pressure compressors and purification systems. Properly processed air is an essential prerequisite for many processes. Purification aims to reduce the undesirable gas components to a required minimum. Our purification systems are tailored precisely to your needs.
|
|
|
|
|
|
Pneumatic equipment is operated with purified and dried compressed air, which represents an extreme charge for the user of breathing masks during permanent use. Dry and cold compressed air causes dry mucous membranes, which may lead to becoming prone to catching a cold.
In accordance with the DIN directives and physiological and medical aspects, breathing air at the workplace ("IAO") must have the following characteristics:
- Free from dust (DIN 3188)
- Free from harmful gases and vapours
- Free from smell
- Temperature between 20 - 24° C
- Relative humididy between 30 - 70 %
- Air flow speed max. 0.15 m/sec.
In order to achieve an optimum painting result, the compressed air used for painting is filtered, dried and, stripped of oil remainders as far as possible. The compressed air thus purified does not comply with the aforementioned requirements and must therefore be further purified for use with supplied air breathing masks.
The breathing air humidifyer AB1 operated with compressed air (spray air) supplies breathing air complying with all requirements.
Basically, it consists of two functional groups for securing the working conditions of users of supplied air breathing masks:
1. Fine filter and activated charcoal cartridge as well as adjustable pressure regulator
- Purification of the compressed air to obtain breathing air
- Exact adjustment of the breathing air network pressure
2. Air warmer and air humidification unit
- Gradual warming of the breathing air for a pleasant climate
- Increase of the breathing air humidity to approx. 40% relative humidity
|
|
WHY HUMIDIFICATION
Even humidity balance, preservation of high quality products, better room conditions for health, ... HUMIDIFICATION THEORY
How does humidification work?
HIGH PRESSURE HUMIDIFICATION
Humidification – by high pressure vaporization
VAPORIZATION UNITS
for offices, housing spaces, etc.
|
|
JS Humidifiers Special Projects Division works with clients to design and produce bespoke humidification solutions.
For precise control of humidity and temperature, extreme outputs, specialist construction for controlled environments or unusual control, whatever the requirement JS will design and manufacture a solution.
|
|
These are used for degassing resins, compound materials, silicone mixes, etc.
They can achieve vacuum levels of 99.5%
Ideal for model makers and prototype builders
|
|
|
Acrueing gases have to be drained, collected and used. Depending on the gas quantity the gases can be deliverd to an existing gas supply system or can be transfered to a gas burner.
|
|
The DryPac dehumidification systems are specially designed to use low levels of energy and to minimize total energy consumption. The DryPac system maintains the air at a constant, precise humidity regardless of weather conditions or load variations.
Using a DryPac system for air dehumidification usually results in a substantial saving in the running costs of the plant and investment in cooling equipment.
DryPac systems can dehumidify air to a relative humidity (RH) as low as 20%. The DryPac can handle target volumes of air.
|
|
|
|
|
|
Precision and modularity.
Double desiccant tower models, with an airflow rate from 50 to 150 m3/h, supply air at a dew point lower than –50°C. The process air temperature can be set up to 200°C (HT version).
Customer oriented solutions:
Precision:
- Electronic control of the process temperature with self-tuning PID algorithm that ensures high precision.
Easy utilisation:
- Simple and complete operator interface
- Microprocessor control
- Large display available in the operator’s language. It shows the functioning status of the machine as well as any possible alarm or warning message.
- On the main screen the following parameters of the dryer can be monitored: Drying temperature, Set-point, Dew Point value
Flexible and modular configuration:
- The operator can simply and easily increase the number of hoppers at any time. Hoppers capacity from 30 to 400 dm³; single or centralised systems.
Intelligent Energy Supervisor:
- In accordance with the effective requirements of the processing machine, the IES system optimises and adjusts the energy utilisation
- Intelligent Material Drying: optimises and adjusts the energy utilisation to prevent material thermal degradation or over-drying.
|
|
Recusorb R-series
2 600 - 13 500 m3h*
R-series is comprised of R-062,-082,-102, -122. They have double wall insulation and in built heat recuperation. R-series is used amongst other applications for manufacturing and storage within the pharmaceutical industry and within food and confectionary manufacturing.
The R series is supplied with the high capacity SSCR Ultra ceramic-silica gel rotor, G3 panel filters, process and reactivation fans and all essential controls.
|
|
F-YHC12X
Hybrid type
Intelligent humidity control
Anti-bacteria and super alleru-buster filter
Timer (2/4 hours)
Dehumidifying capacity = 12L/day
|
|
|
|
|
|
The new Piovan Dryers of the DPA Series use compressed air for the treatment of hygroscopic polymers. 6 models, with a drying capacity ranging from 0,5 to 25 kg/h and average Dew Point value of -25°C (can be extended up to -40°C in the configuration with desiccant towers).
Energy use optimisation
The control permits to manage the airflow on 7 levels, self-adjusting the dryer’s functioning according to the quantity of material present. The system thus avoids wastage of energy as well as of compressed air.
Can be equipped with the energy saving device Intelligent Material Drying (IMD): it ensures optimal management of the drying process avoiding material over-heating or thermal degradation. It carries out a management of the set point, based on granule consumption and it automatically reduces the airflow in the drying hopper, and consequently the consumption of energy required (Plus function).
Self-adaptation of the working parameters
Thanks to the Material Database included in the standard configuration, the control automatically regulates the process conditions once the material has been selected and the hourly throughput has been set. The open Material Database, containing 50 materials complete with pre-defined set values for optimal processing, can be modified, customised and integrated with new data in line with the customer’s production.
Control of correct dehumidification. The electronic system of the DPA dryers includes the Drying Control function. It continuously checks the loading times of the drying hopper and the drying times, and it signals critical events.
|
|
|
Bry-Air's MiniPAC® dehumidifier is the ideal dehumidification solution for smaller facilities in need of reliable humidity control or mold and mildew protection. The MiniPAC® can be installed as a stand-alone unit, or attached to any central air conditioning system to enhance the system's dehumidification capability. A small, yet powerful unit that combats the effects of moisture in up to 8,000 sq. ft. is ideal for a wide variety of applications.
|
|
Recusorb R-51/61R
10 kg/h*
Mid-range industrial desiccant dehumidifiers for medium volume dry air stores and sports halls, museums, small clean rooms and manufacturing processes.
Manufactured in 2333 stainless steel, these units include internal heat recovery, electric reactivation and Auto-Manual mode switching. Pre-wired for simple humidistat control as standard, units are also available for two 2 step binary control (from EH4 2 step controller) or linear capacity control (from EH3 PI controller or BMS control signal).
|
|
F-Y601ZH
Dehumidifier - Desiccant Type ( F-Y601ZH )
Desiccant type
Automatic humidity control
Minus ion
Anti-bacteria and super alleru-buster filter
Timer (2/4/8 hours)
Dehumidifying capacity = 6L/day
F-YZB10X
Dehumidifier - Desiccant Type ( F-YZB10X )
Desiccant type
Automatic humidity control
Mega active ion
Anti-bacteria and super alleru-buster filter
Timer (2/4 hours)
Dehumidifying capacity = 10L/day
|
|
With thirteen standard rotor sizes and a wide variety of packaging options, the Bry-Air Desiccant Cassette can be tailored to match the specific requirements of the challenging applications. With the Bry-Air Desiccant Cassette you will get:
* The latest technology
* Solid welded aluminum construction
* Thirteen standard sizes from 300 to 30,000 CFM of dehumidified air
* Low cost of ownership
* Easier maintenance
* Ultimate flexibility of application
* A machine built to last
|
|
RU and RUF
700 m³/h till 41 500 m³/h*
The standard industrial dehumidifier range from Seibu Giken DST is generally sufficient to cover the majority of drying applications. However, this may not always be the most practical solution.
These high quality stainless steel desiccant rotor cassettes provide greater flexibility to AHU manufacturers who require air to be supplied at dewpoints lower than can be effectively and efficiently achieved using cooling coils.
Specifically designed for use in customised air handling units, all cassettes include the SSCR silica gel rotor, geared drive motor, rotor drive system, radial and peripheral seals
|
|
Evaporative humidifiers provide very economic humidification as, unlike steam humidifiers, the water does not need to be heated. JS' evaporative humidifier range includes models that fit inside ducts/AHUs as well as units for suspended ceilings.
Running costs can be 150 times less than steam systems requiring only a single phase power supply. Many operating features make these humidifiers extremely hygenic and safe to use.
|
|
MinAir
Compact mini-humidifier at the highest level: ideal to complete central dwelling ventilation eg. in low energy houses and in any other application, where a small quantity of steam only is required, eg. in laboratories, etc.
Advantages:
Steam capacity from 0.4 to 2 kg/h
User friendly
LED-display to show set-point and actual relative humidity
Integrated humidity controller
|
|
|
|
Air treatment: Purifiers, Humidifiers, Dehumidifiers
