|
|
| The E-PDISO16 has one built-in 10/100 BASE-T auto-negotiation, high-speed communication port. With the Ethernet interface, you can remotely access and configure your E-PDISO16 from anywhere on the network. Only one computer can control the E-PDISO16 at one time. The networking protocol is TCP/IP. You can send your data over 100 meters at data speeds of up to 100 Mbps using only one Ethernet cable connected to your computer. |
|
Accurate conversion of physical parameters, such as temperature, pressure, and strain, into digital data is a challenging task.
VXI Technology combines superior accuracy, high-density, and modularity specifically targeting these applications.
Essential features such as integrated signal conditioning, internal self-calibration, open signal path detection, and flexible open standard programming interfaces are standard. |
|
The 5810 ethernet interface is a module that connects to the VM-1 controller's system bus to provide 10baseT ethernet connectivity using a Cirrus Logic CS8900A ethernet controller IC.
It can be plugged into a board such as the 5811 Module Board.
An on-board EEPROM, accessed via the I2C Bus, is available for storing the 48 bit ethernet (MAC) address and other configuration information.
Two LEDs on the module can be used to indicate a valid ethernet link and data activity, or can be programmed for other purposes by software commands. |
|
TD-SM LAN G3 is an Ethernet module (10/100BT) offering a cost effective solution.
Universal design to comply with all embedded systems requirements.
Ready to implement: no need to redesign the system to add the telecommunication capability |
|
Semaphore offers a new range of affordable Ethernet Remote Modules of compact size and monoblock construction that can be fixed easily on DIN rail.
The modules connect a wide variety of electrical, electronic, and mechanical devices and sensors -- such as pumps, temperature and pressure transmitters, motors, and more - to computers and applications over standard Ethernet networks (Modbus/TCP), RS485 (Modbus RTU), or other controllers and PLCs.
Each remote I/O module has its own Ethernet Modbus TCP/IP port making it easy to connect the modules to each other with up to 100 meters of CAT5 cable, or even longer distances using fiber optic switches.
There are several types of Ethernet remote I/O modules available with different I/O formats.... |
|
The BradControl family of I/O modules provides a reliable solution for connecting industrial controllers communicating on industrial networks to I/O devices. Both in-cabinet and on-machine harsh environment applications are supported.
In-Cabinet:
The BradControl Block I/O system is an effective way to connect industrial I/O devices to a PLC or PC controller over Ethernet. The BradControl interface solution is comprised of a network adapter and up to 32 expansion modules mounted in an enclosure close to the field devices.
On-Machine:
BradControl I/O modules provide a reliable solution for connecting industrial controllers communicating on Ethernet to I/O devices in harsh environments. Rated for IP67 environments, BradControl I/O modules can be machine mounted and are able to withstand areas where liquids, dust or vibration may be present.
|
|
| ... products without technical information |
| |
The new NETLink PRO for programming, configuring and visualization of programmable controls from Siemens is plugged directly into the CPU of the programmable controller via its 1.2 m connecting cable.
The connecting cable is an active cable and therefore
does not influence the MPI/PROFIBUS. The second
programmer (PG) jack enables connection of a further device to the CPU of the programmable controller.
The new NETLink PRO can optionally also be powered from an external 24 V DC power source.
At the controller end, the NETLink PRO permits the full transmission rate of 12 Mbps via MPI and PROFIBUS. The transmission rate of the TCP network of 10 Mbps or 100 Mbps is automatically detected by the device. At the MPI end, the NETLink PRO enables 12 simultaneous links. Moreover, the new NETLink PRO features automatic baudrate detection and flexible configuration, such as DHCP and a Web interface.
An Ethernet jack instead of a permanently affixed Ethernet cable permits flexible connection.
The 3 m Ethernet connecting cable (straight) is provided with the NETLink PRO.
The MPI/PROFIBUS is electrically isolated from the external 24 V DC power source and from the Ethernet interface (functional separation).
New is the support for RFC 1006 protocol (ISO on TCP).
The firmware is always updateable to the newest volume with the included update-program SHTools.
|
|
|
|
