|
|
|
|
|
|
The Webster DHM 3 Series Digital Hydraulic Multimeter is an all-in-one unit designed to test the performance of hydraulic pumps, motors, valves and hydrostatic transmissions.
The easy-to-use design allows the operator to just switch on and test, without complex setup or special training.
The DHM measures flow, pressure and temperature. In addition, the DHM holds the peak pressure value as well as calculating hydraulic power and volumetric efficiency using the unique P-Q test button.
The DHM is the ideal tool for pinpointing hydraulic system faults, reducing downtime, and helping in preventative maintenance. The design builds on the very successful Webster DHT range of portable testers with the addition of a large digital display and a built-in pressure transducer.
The turbine flow meter with built-in loading valve is bi-directional and specifically designed to enable the operator to simulate the maximum working pressure safely during normal machine operation.
The loading valve has safety discs built-in to protect the operator and the multimeter in the event of excessive pressure, allowing oil to bypass the loading valve INTERNALLY with no spillage of oil from the hydraulic circuit, eliminating any danger to the operator or environmental hazards.
|
|
The Webster HT 2 Series Analogue Hydraulic Testers are designed for testing hydraulic pumps, motors, valves and hydrostatic transmissions. This easy to use diagnostic unit can pin point hydraulic system faults, reducing downtime and help in preventive maintenance.
Accurately measuring flow, pressure and temperature, testers are ideal for conveniently checking, hydraulic system performance or locating faults while operating directional control valves or adjusting valve settings. Webster turbines are designed for continuous monitoring or intermittent use commissioning and servicing hydraulic systems up to 480 bar, 7000 psi pressure.
The pressure loading valve with internal by-pass safety discs, allows progressive build up of pressure to check the flow throughout the working range.
|
|
The Webster DHT 1 Series Digital Hydraulic Testers accurately measure flow, pressure and temperature. Webster testers are designed to conveniently check the performance of hydraulic pumps, motors, valves and hydrostatic transmissions.
This easy to use diagnostic tester has simplified controls and can pin-point hydraulic system faults, reducing downtime and helping in preventive maintenance. The tester comprises a turbine flow block and a large easy to read digital display which indicates both flow and temperature.
The tester has a built-in loading valve to simulate the working pressure during normal machine operation. The built-in safety discs protect the machine and operator in event of excessive pressure, allowing oil to safely bypass the loading valve INTERNALLY with no spillage of oil from the hydraulic circuit, eliminating clean-up costs and environmental hazards.
|
|
The PFM6 Series is a compact, lightweight digital
portable tester designed for fast diagnostic
troubleshooting of all types of mobile or
stationary hydraulic systems and components.
These self-contained testers feature laboratory
accuracy and provide fl ow, pressure and
temperature measurements simultaneously
from one point.
Carrying handle for improved portability
Bi-directional model available
|
|
|
|
|
|
Hydraulic pressure testing system that monitors and diagnoses fluid systems in a snap. Snap-Check enables machinery manufacturers to test system pressure quickly, easily, and leak-free. In the case of larger equipment, Snap-Check enables system pressure to be checked both after it is assembled at the factory and following reassembly at customer locations. The low-profile system identifies operating pressure and surges, without the need for a permanently installed gauge or transducer.
Requiring only one hand for connection and disconnection, CEJN Series 358 couplings and nipples make up the most user-friendly pressure testing system available. The Snap-Check system offers:
- Working pressures up to 60 MPa
- Smooth operation in temperatures from -40 F to +212 F
- Standard red plastic dust caps or optional metal screw-on caps that keep the system clean and free from grit and dirt when not in use
- Variety of thread configurations, including NPT, BSP, BSPT, metric, and SAE
- Long-lasting, reliable, test-port fittings and couplings for numerous applications, such as mobile hydraulic off-road equipment
Snap-Check liquid-filled pressures gauges are available in a wide variety of sizes and pressure ranges.
|
|
|
|
|
|
The Webster DHM 3 Series Digital Hydraulic Multimeter is an all-in-one unit designed to test the performance of hydraulic pumps, motors, valves and hydrostatic transmissions.
The easy-to-use design allows the operator to just switch on and test, without complex setup or special training.
The DHM measures flow, pressure and temperature. In addition, the DHM holds the peak pressure value as well as calculating hydraulic power and volumetric efficiency using the unique P-Q test button.
The DHM is the ideal tool for pinpointing hydraulic system faults, reducing downtime, and helping in preventative maintenance. The design builds on the very successful Webster DHT range of portable testers with the addition of a large digital display and a built-in pressure transducer.
The turbine flow meter with built-in loading valve is bi-directional and specifically designed to enable the operator to simulate the maximum working pressure safely during normal machine operation.
The loading valve has safety discs built-in to protect the operator and the multimeter in the event of excessive pressure, allowing oil to bypass the loading valve INTERNALLY with no spillage of oil from the hydraulic circuit, eliminating any danger to the operator or environmental hazards.
|
|
The Webster HT 2 Series Analogue Hydraulic Testers are designed for testing hydraulic pumps, motors, valves and hydrostatic transmissions. This easy to use diagnostic unit can pin point hydraulic system faults, reducing downtime and help in preventive maintenance.
Accurately measuring flow, pressure and temperature, testers are ideal for conveniently checking, hydraulic system performance or locating faults while operating directional control valves or adjusting valve settings. Webster turbines are designed for continuous monitoring or intermittent use commissioning and servicing hydraulic systems up to 480 bar, 7000 psi pressure.
The pressure loading valve with internal by-pass safety discs, allows progressive build up of pressure to check the flow throughout the working range.
|
|
The Webster DHT 1 Series Digital Hydraulic Testers accurately measure flow, pressure and temperature. Webster testers are designed to conveniently check the performance of hydraulic pumps, motors, valves and hydrostatic transmissions.
This easy to use diagnostic tester has simplified controls and can pin-point hydraulic system faults, reducing downtime and helping in preventive maintenance. The tester comprises a turbine flow block and a large easy to read digital display which indicates both flow and temperature.
The tester has a built-in loading valve to simulate the working pressure during normal machine operation. The built-in safety discs protect the machine and operator in event of excessive pressure, allowing oil to safely bypass the loading valve INTERNALLY with no spillage of oil from the hydraulic circuit, eliminating clean-up costs and environmental hazards.
|
|
The PFM6 Series is a compact, lightweight digital
portable tester designed for fast diagnostic
troubleshooting of all types of mobile or
stationary hydraulic systems and components.
These self-contained testers feature laboratory
accuracy and provide fl ow, pressure and
temperature measurements simultaneously
from one point.
Carrying handle for improved portability
Bi-directional model available
|
|
Air reference dead-weight tester BL1R Oil reference dead-weight tester BL1H
Fields:
- Chemical and Petrochemical Industry
- Food and Beverage Industry
- Pharmaceutical and Biotechnical Industry
- Heating, Ventilation and Air Conditioning
- Machine and Process Industry, Power Plants and Distribution, Automotive Industry
Type: BL1R, BL1H
Application: Calibration of pressure monitoring systems
|
|
Model: SHT5205P; SHT5305P; SHT5506P; SHT5605P; SHT5106P; SHT5206P
Capacity: 200kN; 300kN; 500kN; 600kN; 1000kN; 2000kN
Features:
SHT5000P series are based on SANS SHT5000 series servo hydraulic testing system and improved with side action grips.
This series adopts international advanced side action grip technology and solve the problem of load dropping during large force test and high frequency batch test. Gripping force is auto controlled and stable for tensile test of high strength, high hardness materials, stranded wire, and other hard-to-clamp specimens.
Dual side action allows synchronous clamping specimens and ensures precise center alignment. This deign can also eliminate lateral force on specimens before test which is common in wedge action grips.
|
|
Model: SHT4305W, SHT4605W, SHT4106W
Capacity: 300kN, 600kN, 1000kN
Features:
1. Dual test space provides compression in lower space and tensile test in upper space.
2. Half-open hydraulic grips is easy to place specimens and has high rigidity.
3. Lower crosshead is driven by worm wheel with high stability.
4. Spoke shape load cell is connected with piston, which ensures high precision measurement.
|
|
|
|
|
|
The 600 kN Hydraulic Testing System with Single Side-Acting Hydraulic Grips is completly customizable, the grips are ideal for tensile testing of stranded wire or cable and uniquely feature longer jaw faces to better accommodate gripping. These longer jaw faces are extremely important for tensile testing, as strands can easily slip from conventional grips, ultimately affecting the integrity of the test and test results.
Cost-effectively designed with multiple testing system configurations including tension, compression, bend, shear and flexure, Instrons KN Series Universal Hydraulic Testing Systems allow for a flexible single test space. The versatility of design also enables the user to easily add test stroke or increase the test opening and the testing space is easily accessible due to upper actuator design.
For increased operator and equipment safety, Instrons KN Series ensures that the actuator does not travel past the limits of its design. Superior accuracy is provided by Instrons load cell system and zeroing capability. The variable pressure power pack provides pressure on demand, reducing heat generation for increased oil life, decreasing maintenance and eliminating the need for water cooling.
|
|
Servo-Hydraulic Testing Machines
The ExPress line of machines are a bold new approach to servo-hydraulic machines for static testing. Manufactured to exacting standards, these machines are accurate, tough and cost less than conventional hydraulic testing machines. ExPress frames employ strain gage load cells for direct measurement of force. No need to compensate for piston friction and other non-linearities, these frames offer exceptional accuracy and precision while reducing long-term calibration and service costs.
ExPress frames feature a simple design based upon off-the-shelf components for lower cost, faster delivery and long-term availability. Our conservative design is based upon continuous testing to maximum load for years of maintenance free operation. The hydraulic power supply and electronics are integral with the frame thereby saving valuable lab space.
|
|
Hydraulic universal testing machine
Thousands of applications worldwide prove that the hydraulic universal testing machines are with top quality, high accuracy and high reliability. It is ideal products for Q.C, Q.A. and R&D.
From the applications, the load frame includes:
1.Actuator at bottom
2.Top actuator
3.Load cell measured
4.Pressure transducer measured
5.Dual testing spaces
6.One testing space
7.Load capacity from 50kN up to 3000kN
Whenever you need quick operation or high accuracy servo control test, there is one suitable machine that can meet your requirement for different materials.
|
|
|
|
|
|
1. Performance Characteristic:
The resolution is 500000 Codes, Satisfy the related material experiments the method standard, Control and show automatically in experiment process, Have various control methods and curve forms(Include the true stress-strain), The trial report is programmable.
2. Basic configuration:
One host machine, one servo oil source, one computer of the upscale brand, one A4 color Ink-jet printer, one Germany DOLI EDC-120 apparatus for measuring and controlling, one displacement transducer, MOOG servo valve, one extensometer, one table for meter, accessories.
3. Main Specifications:
3.1. Max. testing tensile force:2000kN
3.2. Range of load measurement:20-2000kN
3.3. Accuracy of testing force reading:1%
3.4. Accuracy of displacement reading: 1%
3.5. Load resolution:250000 steps
3.6. Displacement resolution: 2%u03BCm
3.7. The speed of the piston:0-150mm/min
3.8. Rated pressure of pump:25Mpa
3.9. The max tensile space:0-1200mm
3.10. Amount of column:4 pole
3.11. Stroke of piston: 350
3.12. Dia. Of gripping for round specimen: %u03A615-70
3.13. Thickness of gripping for flat specimen: 5~50mm
3.14. Size of down and up flat: 280280mm
3.15. Dimension of frame:14009205060mm
3.16. Hydraulic resource dimension: 11009001200mm
|
|
|
|
|
|
Electro-hydraulically driven Weld Seam Testing Machine, Model 138
A testing machine made to the demand of several customers, to determine the properties of weld seams of Tailored Blanks. These are sheets "made-to-measure" enabling the production of components with optimum weight and function used to a great extent in the manufacture of automobiles to reduce weight. The high-strength metal sheets used require a high punch force for the deep-drawing test. The weld seam testing machine is a special version of our Universal Sheet Metal Testing Machine, Model 142-20, and is provided with a drawing force of max. 200 kN. The four-column frame with integrated test tool enables the test of sheets up to 300 mm wide. The infinitely variable blank holder force can be read on a pressure gauge whilst the deep-drawing index and the required drawing force are displayed digitally. The sensitivity of the integrated crack detector can be adjusted to the sheet metal quality by way of a potentiometer. After specimen failure the machine returns automatically to its initial position. To evaluate and store the measured data, it is possible to connect the machine to a PC using the corresponding interfaces. The Windows based software calculates and displays the measured values from the ERICHSEN cupping test, e. g. index E, elongation at rupture E in %, tensile strength E, n-value E. Furthermore the force-displacement diagram is recorded. Several tests can be shown in a chart.
|
|
|
|
|
|
|
The machines adopt main unit, which is exported to Shimadzu Corporation Japan for the production of UH-F100A.It use Electrohydraulic Servo oil source, and servo valve imported from Japan. With reasonable construction, beautiful out-looking and high stability. With PC control system, they can realize the close loop control of test load, deformation of specimen, displacement of piston and test processor, and the screen display function of test load, peaking value, specimen deformation, piston displacement. The data processing result can be printed out and can be stored on disk in form of ASCII and can be transmitted through network. Especially the machine is supplied with analogue intelligent setting specialist system. The machine is mainly used to do tensile, compression, bending and shearing test for metal and non-material materials. The customer could set the test control mode automatically according to their requirement so as to conform the customers' special requirement.This series is mainly designed for compression and bending test of building material items, such as concrete, cement specimen and component, etc, also used for compression performance test of rubber pad and top forge test of metal.
|
|
|
Hydraulic static universal materials testing machines with seven different frame capacities to a max of 3,000 kN
|
|
|
|
|
|
This machine is mainly used for metal and non-metal of tension test, compression test, bending test and shearing test.
The oil cylinder is set on the bottom in this machine, the test space can be adjusted automatically by motor, hydraulic damp automatically, and with 4 adjustable columns.
The reading accuracy is 1% , the accuracy of extensometer is 0.5% ,Auto process data of Experiment with a computer, Satisfy the related standard of material experiments , Dynamically display load, elongation, load speed and real time trial curves, automatically calculate Rm (%u03C3b), %u03C3s, ReH (%u03C3su), ReL (%u03C3sl), Rp0.01 (%u03C3p0.01), R p0.05 (%u03C3p0.05), Rp0.1 (%u03C3p0.1), Rp0.2 (%u03C3p0.2), E and so on, can print on trial report and curves. Adopt digital frequency conversion to load, the speed is steady, consume of power is small, the noise is low, oil temperature is low for working long hours, operation is simple, safe and dependable.
Basic configuration:
One host machineCone oil source like piano ,one computer of the upscale brand, one A4 color Ink-jet printer, one load cell ,one extensometer , one table for meter, accessories for extension, compression and bend, , one high quantity pump, one auto hydraulic grip.Have not shearing clamp in test machine of 2000kN
|
|
These series are mainly designed for tensile, compression, bending and shearing test of metallic and non-metallic materials. With special accessory, they can complete mechanics performance test of rubber, belt, chain, steel, cable, cement, brick, concrete and other materials. They are wildly used in machinery, building engineering and material, space flight & aviation, railway, metallurgical, textile, petrochemical and production industry, scientific research institute, college, university and other fields.
|
|
|
|
|
|
Flo-Check USB represents the next generation of hydraulic test equipment. This technologically advanced device simultaneously measures flow, pressure, temperature and power within a hydraulic system. Data is displayed and logged through a custom Windows-based software application; data is received from the Analyzer through a standard USB cable (both software and cable are included with the unit). The unit is bi-directional, provides an accuracy of 1% of full scale, and includes a low-resistance load valve and internal pressure relief discs.
The Flo-Check USB Hydraulic System Analyzer can be used as a stationary or portable tester for both industrial and mobile hydraulic system diagnostics, and analysis of the prognostic health of a hydraulic system. It features flow, pressure, and temperature sensors that are monitored by a data acquisition module. This module records the operating parameters of the system and transfers them to the users laptop via the USB port. It can log up to 12 hours with option to capture data manually or continuous monitoring. Data can be exported to Microsoft Excel and other spreadsheet programs.
Flo-Check is powered through the USB port of a PC, making it easy to setup and ideal for portable applications. Interfaced to the PC application, the device offers a straightforward method of monitoring system parameters complete with data acquisition.
|
|
|
Flo-tech portable testers are the leaders in state-of the-art hydraulic testing equipment. Offered in three models in a variety of sizes, the compact testers are designed for fast, diagnostic troubleshooting of both mobile and stationary hydraulic systems and components. The PFM6 measures flow, pressure, and temperature simultaneously from one point, while the PFM8 series provides an additional dynamometer for power calculation (HP and kW). In addition to portable testers, Flo-tech manufactures a wide variety of in-line turbine flow meters for hydraulic fluids.
|
|
|
The Flo-Check USB represents the next generation of hydraulic test equipment. The device simultaneously measures flow, pressure, temperature and power within a hydraulic system. This data is displayed and logged through a custom Windows-based software application; data is received from the Analyzer through a standard USB cable (both software and cable are included with the unit). The Flo-Check USB is ideal for testing, troubleshooting and diagnosis in mobile and industrial hydraulic applications, and for setting hydraulic components such as pumps, valves and motors. The unit is bi-directional and includes a low-resistance load valve and internal pressure relief discs.
|
|
|
Flo-tech portable testers are the leaders in state-of the-art hydraulic testing equipment. Offered in three models in a variety of sizes, the compact testers are designed for fast, diagnostic troubleshooting of both mobile and stationary hydraulic systems and components. The PFM6 measures flow, pressure, and temperature simultaneously from one point, while the PFM8 series provides an additional dynamometer for power calculation (HP and kW). In addition to portable testers, Flo-tech manufactures a wide variety of in-line turbine flow meters for hydraulic fluids.
|
|
|
The Flo-Check USB represents the next generation of hydraulic test equipment. The device simultaneously measures flow, pressure, temperature and power within a hydraulic system. This data is displayed and logged through a custom Windows-based software application; data is received from the Analyzer through a standard USB cable (both software and cable are included with the unit). The Flo-Check USB is ideal for testing, troubleshooting and diagnosis in mobile and industrial hydraulic applications, and for setting hydraulic components such as pumps, valves and motors. The unit is bi-directional and includes a low-resistance load valve and internal pressure relief discs.
|
|
|
|
