|
|
Spinner-Grip Flange Lock Nut
Spinner-GripTM Flange Lock Nuts are the latest innovation in locking nuts. Free Spinning installation eliminates the need to "wrench" the nut down the thread.
Grade 8 strength and quality, but will work with any grade of fastener.
Does not damage threads or plating on fasteners.
Locks to the part - not to the threads. (Exceptional performance in applications with heavy vibration)
Greater temperature range than nylon insert locknuts.
Hardness of 28 - 38 HRc - More effective at maintaining clamp load under vibration.
Not limited to 5 reuses, as with most other torque lock nuts.
|
|
Special fastening components SEAL LOCK® sealing nuts and HELICOIL® lock nuts
Special fastening components are manufactured on fully automatic production and assembly systems:
SEAL LOCK® sealing nuts, the cost-effective solution for reliable sealing of nut and bolt connections in threads and under head presentation against gaseous and liquid media under high pressure. (hydraulic systems, fuel systems and pneumatic systems)
The HELICOIL® lock nut with integrated HELICOIL® SCREWLOCK® is the solution for heavy-duty threaded joints with resistance to torque loss.
HELICOIL® nuts satisfy the high requirements with regard to corrosion, temperature loads, low thread friction and the reusability of threaded parts.
|
|
AS, AC, LAS, LAC
Floating action compensates for mating hole misalignment. Available with locking or non-locking threads. Thread sizes #4 to 1/4" and M3 to M6.
LK, LKS, LKA
The PEMFLEX® design provides MIL-N-25027 locking performance without damaging mating threads. Thread sizes #2 to #10 and M2.5 to M5.
WN, WNS
Unique PEM design prevents burnouts and eliminates the need for indexing and retapping to remove weld spatter. Thread sizes #4 to 1/4" and M3 to M6.
|
|
KPS6 Used in plated thru-holes in multi-layer P.C. boards. The self-expanding shank ensures positive contact with plated thru-holes. Thread sizes #4 to #10 and M3 to M5.
SOAG, SOSG Used to ground P.C. boards to steel or aluminum chassis. Annular projecting teeth eliminate the need for serrated or starwashers to make good electrical contact with the circuit foil. Thread sizes #4, #6, and M3, M4.
KFE, KFSE
Standoffs available with or without threads for mounting into P.C. boards, for spacing or stacking.Thread sizes #4, #6 and M3.
|
|
... see all the products in the category
Nuts
|
AS, AC, LAS, LAC
Floating action compensates for mating hole misalignment. Available with locking or non-locking threads. Thread sizes #4 to 1/4" and M3 to M6.
LK, LKS, LKA
The PEMFLEX® design provides MIL-N-25027 locking performance without damaging mating threads. Thread sizes #2 to #10 and M2.5 to M5.
WN, WNS
Unique PEM design prevents burnouts and eliminates the need for indexing and retapping to remove weld spatter. Thread sizes #4 to 1/4" and M3 to M6.
|
|
KPS6 Used in plated thru-holes in multi-layer P.C. boards. The self-expanding shank ensures positive contact with plated thru-holes. Thread sizes #4 to #10 and M3 to M5.
SOAG, SOSG Used to ground P.C. boards to steel or aluminum chassis. Annular projecting teeth eliminate the need for serrated or starwashers to make good electrical contact with the circuit foil. Thread sizes #4, #6, and M3, M4.
KFE, KFSE
Standoffs available with or without threads for mounting into P.C. boards, for spacing or stacking.Thread sizes #4, #6 and M3.
|
|
|
... see all the products in the category
Inserts
|
|
|
