push-fit fitting / cylindrical / stainless steel
push-fit fitting
DN 65 - 200, PN 10 | 924

Diameter: 50 mm - 300 mm

This product is ideal for pipe coupling for PE pipes (restraint). It also supports liner of stainless steel for PE pipes. Use a support liner for thin-walled PE pipes. Note: Don't apply any grease or soap on the pipe ...

push-in fitting / straight / stainless steel / pneumatic
push-in fitting
F 100/x FLASH

Diameter: 4 mm - 12 mm

Push-in pneumatic fittings Usable with these pipes: pa6,pa11,pa10.12, pa12, ptfe, polyethylene , polyurethan Available in: (with gauged diameter): ø4mm ø6mm-ø8mm-ø10mm-ø12mm

See the other products
Olab
push-in fitting / elbow / stainless steel / pneumatic
push-in fitting
F 100/xx FLASH

Diameter: 4 mm - 12 mm

Push-in pneumatic fittings Usable with these pipes: pa6,pa11,pa10.12, pa12, ptfe, polyethylene , polyurethan Available in: (with gauged diameter): ø4mm – ø6mm-ø8mm-ø10mm-ø12mm Pneumatic ...

See the other products
Olab
double-ferrule fitting / straight / stainless steel
double-ferrule fitting
1/8 - 1" | UTR

Diameter: 0.13 in - 1 in

The UTR two-ferrule compacting fittings are utilized to join two metric or partial containers of the same or different outside measurement without either thread or welding. The resulting union is totally hermetic, both ...

See the other products
TECVAL, S.L.
ring fitting / T / double / stainless steel
ring fitting
1/8 - 1" | CHT

Diameter: 0.13 in - 1 in

The CHT two-ferrule layering tees are utilized to amass a threated or welding end to a metric or fragmentary tube. The resulting union is totally hermetic, both for high pressure and temperature. The characteristics include - run "RU" ...

See the other products
TECVAL, S.L.
union fitting / double-ferrule / elbow / stainless steel
union fitting

Diameter: 1.6 mm - 28 mm
Operating pressure: 250 bar

For high and extreme requirements * Unions, valves, couplings * 1.6 - 28 mm * max. 250 bar * -110 to +300 C * for aggressive air, gases, liquids and oils in an aggressive environment * e.g. in chemical plants, ...

union fitting / straight / stainless steel / high-pressure
union fitting
L series

Diameter: 6 mm - 18 mm
Operating pressure: 400 bar

... corrosion resistant - compact design - radial dismounting - minimal dead space - very good resistance to vibration Material Stainless steel 1.4571 with the alloy X 6 CrNiMoTi 17 12 2, DIN EN 10216-5 ("H AISI 316 Ti). Nominal ...

weld fitting / elbow / stainless steel
weld fitting
90 °, 1/4 - 6 " | TEG2C series

PRODUCT: Stainless Steel fittings comply with ASME BPE standards. Gaskets are made from compounds which are FDA approved and USP 87, 88 Pharmaceutical Class VI certified. SIZES: Stainless Steel ...

See the other products
EGMO LTD.
weld fitting / elbow / stainless steel
weld fitting
45 °, 1/4 - 6 " | TEG2K series

PRODUCT: Stainless Steel fittings comply with ASME BPE standards. Gaskets are made from compounds which are FDA approved and USP 87, 88 Pharmaceutical Class VI certified. SIZES: Stainless Steel ...

See the other products
EGMO LTD.
threaded fitting / straight / stainless steel
threaded fitting

The AWH features its product to be highly reliable and cost efficient. Every product had undergone series of advance processes and standards to ensure the quality service of the product gives. All materials are accessible with WAZ 3.1 ...

See the other products
Armaturenwerk Hötensleben GmbH
threaded fitting / conical / stainless steel
threaded fitting
DIN 11851

... AD2000-W2, if requested. They include various union parts, DIN 11851 and DIN/ISO and DIN/inch, female and male connections and fittings, rotating union parts, hose union parts, bellows, SMS, IDF,RJT and DS unions, clamp ...

See the other products
Armaturenwerk Hötensleben GmbH
threaded fitting / cross / steel / stainless steel
threaded fitting
FS2650-FG Series

Diameter: 0.17 mm - 1.92 mm

... 0.85 9/16-18 0.85 0.850 0.172 0.562 FS2650-06-06-06-06-FG 3/8 Steel Forged 11/16-16 11/16-16 0.264 0.264 0.980 0.264 11/16-16 0.98 11/16-16 0.98 0.980 0.264 0.750 FS2650-08-08-08-08-FG 1/2 Steel Forged 13/16-16 13/16-16 0.378 0.378 1.100 0.378 13/16-16 1.100 ...

See the other products
BRENNAN Industries
threaded fitting / straight / stainless steel / for tubes
threaded fitting
0404 series

Diameter: 0.25 in - 2 in

... D DRILL T WIDTH 0404-04-02 1/4 Steel 0.562 0.256 1/8-27 0.500 0.188 0.19 0404-04-02-SS 1/4 Stainless Steel 0.562 0.256 1/8-27 0.500 0.188 0.19 0404-04-04 1/4 Steel 0.812 0.256 1/4-18 0.625 0.172 0.25 0404-06-04 3/8 Steel 0.812 0.381 1/4-18 0.625 0.281 ...

See the other products
BRENNAN Industries
flange fitting / elbow / stainless steel
flange fitting
0.75" - 4", 45° | E45 series

Diameter: 0.75 in - 4 in

UHV vacuum rating approx. 1x10-13 torr Temperature range from -200oC up to 450oC Manufactured from 304L stainless steel Radius elbow design

See the other products
A&N Corporation
flange fitting / elbow / stainless steel
flange fitting
0.75" - 6", 90° | E90

Diameter: 0.75 in - 6 in

UHV vacuum rating approx. 1x10-13 torr Temperature range from -200oC up to 450oC Manufactured from 304L stainless steel Radius elbow design

See the other products
A&N Corporation
weld fitting / cylindrical / stainless steel
weld fitting
1/4 - 6" | ART. 110 series

Diameter: 0.25 in - 6 in

According to Table: DT-22 Sulfur: ≤ 0,017% SF-1 Int. finishing: Ra ≤ 0,4 µm Machined Finish Ext. finishing: Ra ≤ 0,8 µm Machined Finish SF-4 Int. finishing: Ra ≤ 0,4 µm Electropolished Ext. finishing: Ra ≤ 0,8 µm Electropolished

See the other products
RATTIINOX SRL
weld fitting / cylindrical / stainless steel
weld fitting
1/2 - 6" | ART. 115 series

Diameter: 0.5 in - 6 in

SF-1 Int. finishing: Ra ≤ 0,4 µm Machined Finish Ext. finishing: Ra ≤ 0,8 µm Machined Finish ML Int. finishing: Ra ≤ 0,4 µm Machined Finish Ext. finishing: Ra ≤ 0,8 µm Mirror Polished

See the other products
RATTIINOX SRL
weld fitting / straight / stainless steel
weld fitting
FG4DIN, FG4DINR-I

See the other products
TECOFI
ring fitting / T / stainless steel
ring fitting
FG4DINT3M-I

DIN FITTINGS DIN male tees. Body material: Stainless Steel

See the other products
TECOFI
threaded fitting / straight / stainless steel
threaded fitting
DN6 - DN51, 1/4 - 2"

threaded fitting / straight / stainless steel
threaded fitting
-273° C/+ 450° C, 1/4" - 1" | ZeroCon®-Crown

... and is a threaded connection system that is ideal for use in pipe joints and welded systems in the food, pharmaceutical, and steel industries. The unit consists of a pressure joint and a threaded joint together with ...

double-ferrule fitting / straight / stainless steel
double-ferrule fitting
3 000 - 8 000 psi | Dynatube®

... envelope over all other types of aerospace fittings. The fitting is a dual seal fitting that provides a self-locking feature. The original “beam seal” fitting designed ...

threaded fitting / male / elbow / stainless steel
threaded fitting
MX 16 xx xx

See the other products
HNC GROUP A/S
threaded fitting / T / stainless steel
threaded fitting
MX 21 xx xx

See the other products
HNC GROUP A/S
compression fitting / straight / stainless steel / for the pharmaceutical industry
compression fitting
TRI-CLAMP: BS-DIN, ISO

The Tri-clamp is a reliable solution for a range of applications in pharmaceutical facilities, food processing plants, and chemical-related industries. All of its contributing component adheres to BS, DIN and ISO standards. This set ...

bulkhead fitting / splined / straight / stainless steel
bulkhead fitting
600 series

... complete range of swaged style hose end fittings. Meeting the demanding requirements of the world's top racing professionals has allowed us to offer this full range available in JIC, Metric & BSP banjo and three way ...

See the other products
GOODRIDGE FLUID TRANSFER SYSTEMS
threaded fitting / T / stainless steel
threaded fitting
S5135-03C

... complete range of swaged style hose end fittings. Meeting the demanding requirements of the world's top racing professionals has allowed us to offer this full range available in JIC, Metric & BSP banjo and three way ...

See the other products
GOODRIDGE FLUID TRANSFER SYSTEMS
threaded fitting / reducing / hexagonal / stainless steel
threaded fitting
5.B

Hexagonal glass-shape reduction INOX steel Body material: Stainless steel

threaded fitting / reducing / conical / stainless steel
threaded fitting
10.D

Conical reduction INOX steel Body material: Stainless steel

male fitting / ring / elbow / stainless steel
male fitting
DN 4 - 6, 24°

See the other products
Fritsche GmbH & Co. KG
threaded fitting / elbow / stainless steel
threaded fitting
DN 4 - 6

See the other products
Fritsche GmbH & Co. KG
threaded fitting / elbow / stainless steel
threaded fitting
FG20 series

CONNECTION • B.S.P. female thread Rp1/s-Rp4 (DIN 2999) • B.S.P. male thread Außengewinde, RVs- R4 (DIN 2999) PRESSURE RANGE Up to nominal pressure PN 10 By unions with PTFE-sealing (only by Art. FG42xx, FG43xx, FG50xx, FG51xx and FG53xx) ...

See the other products
END-Armaturen GmbH & Co. KG
threaded fitting / T / stainless steel
threaded fitting
FG24 series

CONNECTION - B.S.P. female thread Rp1/s-Rp4 (DIN 2999) • B.S.P. male thread Außengewinde, R1/a-R4 (DIN 2999) PRESSURE RANGE Up to nominal pressure PN 10 By unions with PTFE-sealing (only by Art. FG42xx, FG43xx, FG50xx, FG51xx and FG53xx) ...

See the other products
END-Armaturen GmbH & Co. KG
splined fitting / straight / stainless steel
splined fitting
DN 40 - 150 | 101 series

Morsello Inox's Garolla's fittings of the 101 series serve as half rubber hose adapters. They are short, and can be made in sizes: 40, 50, 60, 70, 80, 100, 120 and 150. They can be made out of AISI 304 TIG stainless ...

See the other products
Morsello Inox srl
splined fitting / straight / stainless steel
splined fitting
40 x 20 - 120 x 100 mm | 102/A series

Morsello Inox's Garolla fittings are stainless steel welded pipes according to AISI 304 TIG standards. It is designed after going through various mechanical phases, including cold forging, turning and ...

See the other products
Morsello Inox srl