|
|
EPS cartridges are designed to meet the special needs of the electronics and high purity chemical industries. Polyethersulfone membrane cartridges are resistant to most acids and bases and capable of handling strong sanitization agents. High flow rates make Polyethersulfone a good choice for central DI water systems. This membrane will also handle elevated process temperatures in compatible fluids. To minimize extractables, each cartridge module is pulse, power flushed until the rinse effluent reaches 17+ Megohm-cm and less than 3 ppb TOC. Each cartridge module is also individually tested.
|
|
Application
Filtration of water, cooloing agents, process water, aqueous solutions, aggressive and chemical liquids
Special characteristics
Filtration direction from inside to outside, in case of change of elements the contamination cannot reach the clean side. Easy change of elements without getting in touch with the medium.
Design / technical data:
In-line filter / duplex-filter, nominal width beteen 25 and 500 max.
Working pressure: 40 bar at 90°C, materials: steel; coated steel, stainless steel
|
|
690 Marine Bronze Duplex Strainer
Size: 3"
Strainers provide positive and inexpensive protection for costly pumps, meters, valves,
and other similar mechanical equipment by straining foreign matter from the connected piping
system. Installation of a strainer before mechanical equipment can ensure trouble free service
and avoid costly shutdowns for repair or replacement of equipment damaged by foreign
matter. The size of the perforation or mesh in the basket screen will determine the smallest
particles captured. See Strainer Information section of the Mueller Steam Specialty
Engineering binder for detailed information including sizes and materials available.
Typical Service
As with all duplex strainers, these are used where flow cannot be shut down for basket cleaning.
These sight glass duplex strainers are typically used in engine cooling water systems in seawater and heat exchanger applications.
When supplied with fine mesh lined baskets, they can be used to clarify potable water supplies.
Features
Clear acrylic basket chambers allow direct visual inspection of the fluid flow and basket condition.
Flow diversion is accomplished by a single tapered plug diverter that moves 90°, thereby opening one chamber while closing the other.
Sight glass chambers and baskets are accessed for easy cleaning, inspection, and replacement by removal of two wing nuts. |
|
You need cartridge filters with long life, high efficiency and low total operating cost and that's what you get from GE Water and Process Technologies. With an extensive range of filters to meet all of your microfiltration needs:
- RO pre-treatment
- Pure water filtration
- Food and Beverage
- Electronics
- Oil and gas
- Chemical processing
- Pharmaceuticals
- Medical
- General industry
GE provides, and continues to develop, high-performance products backed by years of experience. Our cartridge filters are made with no wetting agents, solvents, anti-static agents, or binders. FDA-compliant filters are available for food and beverage contact. |
|
On-Site Pack Making:
SPX Cooling Technologies' extensive knowledge and experience in manufacturing Marley cooling tower PVC film-fill carries over into PVC media production for the biomedia market. Our capabilities in fill production include the ability to manufacture adhesive bonded packs at the jobsite. In some cases, the ability to manufacture fill on-site means a lower cost to the customer and assures the highest quality product available and eliminates the dependency on freight carriers.
This ability also assures a timely delivery of packs at the jobsite potentially
reducing construction downtime and labor costs.
Construction Services:
As a single-source supplier for cooling tower components, SPX Cooling Technologies extends the same philosophy to water waste treatment/biomedia installation. Construction is an integral part of the teamwork responsible for function and performance of your biological wastewater treatment. MARPAK biomedia is installed under the supervision of trained and experienced personnel-in most cases the entire crew are full-time SPX employees. Our superintendents are trained in the proper procedures for Marley fill pack installation-their many years of experience enables them to spot potential problems during the construction phase. SPX Cooling personnel installing Marley components on a regular basis insures consistency and quality. |
|
| ... products without technical information |
| |
Oil and Water Vapor Adsorbers (25-2,200 scfm)
Oil vapor can be very detrimental to many products and processes including food, pharmaceutical, instrument, hospital and electronics applications. In these cases an oil adsorber should be installed downstream of both lubricated and non-lubricated air compressors as hydrocarbon vapors are found in ambient air and can be concentrated in the compressed air stream. Oil adsorbers use a charge of activated carbon to remove unwanted hydrocarbon vapors. These adsorbers can be used as single tower water vapor adsorbers with a charge of activated alumina.
Stainless steel diffuser and adsorbent support screens for superior corrosion resistance.
Down flow design for less fluidization and longer adsorbent life.
ASME section VIII designed, manufactured and stamped (where applicable) for certified quality assurance
Specially selected carbon and aluminum adsorbents for low pressure drop.
Separate fill and drain ports for ease in adsorbent replacement.
|
|
| ... products without technical information |
| |
Filters separator diesel water/gas oil RACOR
Description:
- A broad range of filters for the protector of the engines with the series SPIN ONE of Parker RACOR conceived for the systems of modern injection.
- Flow of 57 with 600l/h.
- Filtration of 2,10 or 30 microns
Advantages:
- Almost indestructible transparent Bowl, resistant to UV and winter temperatures.
- Powerful pump of starting and heaters integrated in the head of the filter.
- Filter Media hydrophobic Aquabloc.
- Water Presence detector.
Applications:
- Filtration of diesel biodesel and gasoline for TP, Bus, Truck, Agriculture, Mobile, Navy, Generator sets |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
Oil and Water Vapor Adsorbers (25-2,200 scfm)
Oil vapor can be very detrimental to many products and processes including food, pharmaceutical, instrument, hospital and electronics applications. In these cases an oil adsorber should be installed downstream of both lubricated and non-lubricated air compressors as hydrocarbon vapors are found in ambient air and can be concentrated in the compressed air stream. Oil adsorbers use a charge of activated carbon to remove unwanted hydrocarbon vapors. These adsorbers can be used as single tower water vapor adsorbers with a charge of activated alumina.
Stainless steel diffuser and adsorbent support screens for superior corrosion resistance.
Down flow design for less fluidization and longer adsorbent life.
ASME section VIII designed, manufactured and stamped (where applicable) for certified quality assurance
Specially selected carbon and aluminum adsorbents for low pressure drop.
Separate fill and drain ports for ease in adsorbent replacement.
|
|
System of Extraction and
decantation of Abrasive Muds
SEBA
Eductor continues abrasive deposit for
installations of cutting jet of water:
It is using a particular drain that the abrasive deposit is continuously aspired, in a simultaneous and reliable way, at various places of the basin of cutting and guided towards a container of decantation with one or two Big Bags. The water which runs out by Big Bags is filtered and repompée towards the places of aspiration of the basin of cutting by means of a system of washing to counter-current to guarantee a cycle of aspiration. The fine sands deposited in the tank Re-are also pumped in the basin of cutting. Doors simplify the withdrawal of Big Bags filled.
Advantages:
Better profitability thanks to a reliable process and with a reduction of the expenses of evacuation of the deposit.
Process of aspiration and washing with completely automatic counter-current.
High rate of decantation thanks to the use of second Big Bag.
Return of water filtered to the basin of cutting.
Possible process of decantation until a distance of 5 m of the basin of cutting.
Extension simplified for static basins of cutting until 2x3 m2
Volume of evacuation decreased thanks to the deposit drying oven.
Handling facilitated for an effective transport of Big-Bags |
|
| ... products without technical information |
| |
|
|
