Active electronic filters

The Motor filters DIL M12-XMSM is a suitable resolution for the clampdown of interference with three-phase motors. The device diminishes the voltage peaks and high frequency components caused by strident voltage rises. ...

Current: 30 A - 400 A
Voltage: 480, 400 V
Frequency: 60, 50 Hz

... filtered for maximum filter effectiveness Power factor correction both inductive and capacitive Phase current balancing, improvement of consumption in neutral (4W model) If higher filtering capabilities ...

... currents (capacitive). These filters offer a configurable function priority for an optimal use of the filter capabilities according to the installation needs. n case of higher filtering ...

Voltage: 400, 480 V
Frequency: 50, 60 Hz

FAR-Q filters have been designed for Power factor correction purposes in networks with an average harmonic distortion, i.e., in networks where the objective is to improve the power factor and filter harmonics ...

Current: 1 A - 20 A
Voltage: 250 V
Frequency: 400 Hz

Rated currents up to 20 A Excellent performance/size ratio Optional medical versions (B type) according to IEC/EN 60601-1 Snap-in versions (S and S1 type) Hot inlet versions (HI type) Optional overvoltage protection (Z type) Operating ...

Current: 1 A - 10 A
Voltage: 250 V
Frequency: 400 Hz

Rated currents up to 10 A Integrated dual fuse holder Optional reduced leakage current versions (A/B type) Complies with IEC/EN 60601-1 Snap-in versions (S type) High attenuation performance Voltage : ≤ 250 V Operating frequency ...

Current: 2, 5, 8 A
Voltage: 350 V
Frequency: 60 Hz

Voltage rating up to 350 VAC Current rating 2 A, 5 A and 8 A Offers attenuation fitting to lighting application Compact, space-saving design Cable outlets with enhanced length give freedom for flexible installation Operating frequency ...

Current: 1,000 A
Frequency: 45 Hz

... interference filters Drives with rectifier supply produce low and high frequency system interference with their pulse-type charging currents, which are limited by EMC regulations. Compliance with standards is ensured ...

Frequency: 45 Hz - 65 Hz

Harmonic filters are KEB's innovative solution to reducing network harmonics. The units can be planned simply as a power choke right from the design stage of an electrical switchboard, for compliance with many of the ...

Frequency: 100 Hz - 400 Hz

... COMBILINE sine wave filters limit loads to the admissible limit values and provide the necessary protection of enamel insulation and winding heads on long motor lines and special motors. Protection by sinusoidal ...

Frequency: 100 MHz - 3,000 MHz

... band pass filters and band reject filters (also referred to as band-stop filters or band-rejection filters) are bench top units designed for lab use where they are an ...

Current: 600 A
Voltage: 520 V

Delta EMI filter offer varied voltage range, single phase 115/250Vac, 3 Phase520Vac and up to 600A maximum rated current. Different kind of connection also available. Delta EMI filter can associate customer ...

Our common-mode filters, for example, are suitable for high-speed differential signal interfaces in IT and communications devices such as USB 3.0, DVI, HDMI, and Serial-ATA. The common-mode filters for ...

Current: 1, 2 mA
Voltage: 115, 250 V
Frequency: 50, 60 Hz

• Rated voltage : 115/250 VAC • Power line frequency : 50/60 Hz • Climatic category : HMF 25/100/21 • Max. leakage current for standard version each line to ground @ 115VAC 60Hz: 1,0mA @ 250VAC 50Hz: 2,0mA • Hi-pot rating ...

Current: 1, 4 mA
Voltage: 440 V
Frequency: 50, 60 Hz

• Rated voltage : 440 VAC • Power line frequency : 50/60 Hz • Max. leakage current for standard version each line to ground @ 10 A 250VAC 50Hz: 1,0mA @ 20 A 250VAC 50Hz: 4,0mA • Hi-pot rating (1 minute) Line to ground ...

Voltage: 115, 250 V
Frequency: 50, 60 Hz

Electrical specifications •Rated voltage : 115/250 VAC • Power line frequency : 50/60 Hz • Climatic category : HPF 25/085/21 • Max. leakage current for standard version each line to ground

Frequency: 1 Hz - 15,000 Hz

... frequency due to load factors. Variants BP/04/N provides narrow band frequency filtering between 1 Hz - 15 kHz. BP/04/W provides wide band frequency filtering between 1 Hz and 15 kHz.

Current: 30 A - 200 A
Voltage: 380, 600 V
Frequency: 50 Hz

With the development of power electronic technology, the application of power electronic equipment, such as all kinds of rectifier, is widely used in industry, traffic and domestic appliance, and the ...

The series of Harmonic filter reactors, which is manufactured by Entes, is device that is suitable for use in serial connection with capacitor banks in power factor correction components. By utilizing these kinds of reactors, ...

The VLT Advanced Active Filter from Danfoss is made for places where many drive assemblies have to be managed. This will review a signal and will adjust it to make it more efficient in the event that ...

The sine wave filters are suitable for various applications, especially those that require the provision of sinusoidal motor voltage, in a phase-to-phase manner, as well as the reduction of insulation stress and the elimination ...

Frequency: 1 Hz

Key Facts - Automatically tuned - Medium RF power - Medium selectivity - Bypass for distress frequencies - Stationary and mobile use Features & Benefits - Compact 19" design, 3 HU - Combined VHF/UHF ...

ST has many EMI filters and protection units that work in many interfaces for different communication needs and can work for microphones, memory cards and many other interfaces. These are used with interfaces that use ...

This product is a comprehensive solution for harmonic filtering around the world. It can be used as a displacement power factor correction device individually or in combination with harmonic mitigation. This device not ...

Voltage: 380 V - 690 V
Frequency: 50, 60 Hz

Active Harmonic Filters (Harmonic Correction Units — HCU2) provide dynamic harmonic correction by actively injecting the required currents into the customer's electrical distribution system that cancel ...

Frequency: 2,350 MHz

... Single-ended operation Small size: 1.4 x 1.2 x 0.46 mm Chip scale package RoHS compliant, Pb-free Qorvo's advanced LowDrift™ filters provide industry-leading, ultra-stable temperature performance and an enhanced ...

Suppressor modules from Murrelektronik ensure machine availability. The benefits of suppressor technology are enormous and far outweigh the measures linked with its deployment. For a small price, you can prevent malfunctions or faults ...

Current: 1 A - 16 A
Voltage: 250 V
Frequency: 50 Hz - 60 Hz

... temperature max. 45 °C Degree of protection IP 20 Advantages For general requirements Single‑stage filter concept Efficient filter effect against line‑bound interference emissions ...

Current: 0.5 A - 6 A
Voltage: 250 V

0.5Ato 6A, 250VAC EMI Filters Features ♦ Low Cost (Than RSAL Series) ♦ Lug orWire Terminations ♦ Low Earth Leakage Current Option ♦ Conforms to UL, CSA and EN Safety Agency Certifications

Current: 4 A
Voltage: 24 V

Product information High insertion loss over a broad frequency range Optimised against interferences in the lower frequencies Extra slim enclosure design, only 22.5 wide Self-extinguishing polycarbonat housing acc. to UL94V1 Suitable ...

Current: 50 A - 60 A
Voltage: 120 V - 690 V

Arteche offers two types of harmonic filters for use with 1-phase non-linear loads. Type SLPF is a low pass filter that attenuates all harmonic frequencies and Type THF is a 3rd Harmonic blocking filter ...

ON Semiconductor offers LC, RC, and common mode filters for a wide variety of audio and data interfaces.

Frequency: 70 MHz - 168 MHz

Shoulder Electronics presents BF series Surface acoustic wave (SAW) filter. For solder heat resistance, the equipment terminals should be dipped into the solder bath for 10±1 sec. The temperature should ...

... fundamental frequency. The filters are commonly created with serial filters made by the capacitors which are conformed at the harmonic frequency that should be phased out. The rectifiers are the generators ...