Adjustable LED drivers
Electrical power: 10.8 W - 25.2 W
Input voltage: 24 V
Primary current: 350, 500, 300, 600, 700 mA
... driving high power LEDs. It features high efficiency, wide input voltage range, high operating temperature, PWM and analogue dimming, remote ON/OFF control, and SMD package which facilitates the installation. It ...
Electrical power: 3.3 W - 43.2 W
Input voltage: 24 V
Primary current: 1,000, 1,200 mA
KC24H series is step-down constant current sources for driving high-power LED featured in high efficiency and wide range of input voltage, high operating temperature, and act in PWM dimming, analogue dimming and remote ...
Electrical power: 3 W
Input voltage: 5 V
Primary current: 80 mA
... Up Type DC/DC Converter for White LED The TB62763FMG is a high efficient Step-Up Type DC/DC Converter specially designed for constant current driving of White LED. This IC can drive 2-6 Hi-current ...
... the LED itself 2. Thermal management of the heat generated by the LED 3. The electrical supply to the LED The driver is the device used to control the electrical supply ...
Input voltage: 220 V - 240 V
Primary current: 0 A - 1.5 A
... are theoretically determined values, which does not guarantee the lifetime of the product or of the electrolytic ) h •Unit: LED •Input current: 300 mA •DC output: connecting bracket 0,5...1,5 mm² •Output voltage tolerance: ...
Electrical power: 1.9 W - 3 W
... Designed for compact LED replacement lamps, LinkSwitch-PL enables very small and low cost TRIAC dimmable, single-stage, power factor corrected, constant current drivers for solid state lighting. LinkSwitch-PL ...
Electrical power: 32 W
Input voltage: 4.5 V - 36 V
Primary current: 0.13 A
The MAX20444 is a 4-channel backlight driver with boost controller for automotive displays. The integrated current outputs can sink up to 130mA LED current each. The device accepts a wide 4.5V to 36V ...
Electrical power: 40 W - 600 W
Input voltage: 100 V - 305 V
... options: output adjustable via potentiometer; 3 in 1 dimming (1~10Vdc or 10V PWM signal or resistance); timer dimming Type “HL” LED drivers for use in Class I, Division 2 hazardous ...
Input voltage: 8 V - 24 V
Primary current: 7 mA
... PWM dimming allows LED currents to be controlled in 500:1 ratio. The LED sink current is set by an external R_ISET resistor (see chart at right). More than one LED sinks can be combined ...
Input voltage: 0 V - 100 V
Primary current: 120 A - 1,000 A
The AL5801 combines a 100V N-channel MOSFET with a prebiased NPN transistor to make a simple, small footprint °C driver. The °C current is set by an external resistor connected from REXT pin (4) to GND pin (6). The internal ...
Electrical power: 9 W
Input voltage: 100 V - 240 V
Primary current: 350, 700, 550 mA
Single Dimming Series | Wireless Driver SPECIFICATION Rated Power 9W Input 100-240V ~ 50/60Hz Output-(Option) A-350mA 35-45V DC B-550mA 18-28V DC C-700mA 12-22V DC Max. Tc. 75⁰C Max. Ta. 50⁰C Min. Ta. -15⁰C Size W131*D45*H27.3 ...
Electrical power: 80 W - 200 W
Input voltage: 108 V - 305 V
Primary current: 0.7 A - 2.8 A
... 100,000hrs •Type HL LED Driver for use in Class I Division 2 Hazardous Location Luminaires •All-Round Protections: Short Circuit/ Over Voltage/ Over Temperature •Safety: Meet IEC61347-2-13, UL8750 ...
Your suggestions for improvement:
Receive updates on this section every two weeks.